User's Manual

7
Playing Compact Disc / MP3 Disc
 Getting start
1. Switch on the unit by pressing the On/Standby button (2), then press Function button (8) to change to “ CD ” mode and the LED
will have “ - - - - “ flashing.
2. Push the CD tray open (7) to open the CD tray.
3. Place a CD with the printed side facing up and then close the CD tray.
4. Focus search will performing and the LED display will have “ - - - - “ flashing. Once the focus search is completed, the unit will
start playback of CD automatically. The LED display will first show the total number of track and then change to the number of
track and then display the playback time for the first 5-10 seconds. The display will finally show the time.
5. Press the Volume knob (3) to the desired volume level.
 Play / Pause mode
1. To interrupt, press the Play/Pause button (9) once, the playing time will freeze on the LED display for a while, then change
to the time display. Press again to resume normal playback.
 Stop mode
1. If the Stop button (11) is pressed during play or when the music is paused the system will stop.
 Skip mode (skip up / skip down )
1. In play mode, if the SKIP up button (10) is pressed, the track number of the next track will be displayed and the track will
play.
2. In play mode, if the SKIP down button (10) is pressed, the track number of the previous track will be displayed and the
track will play.
Important: When you press the CD function button during time display, the unit will first show up the number
of current track. Please press again the same CD function button to confirm the operation. This is a normal
operation.
 Repeat function
A. Repeat 1 mode
Press the Repeat button (5) during playback once to enable repeat the current track. And the Rep 1/all/Snooze LED indicator (18)
will flash for a while and then will disappear. Press the Repeat button (5) twice more to cancel the repeat mode.
B. Repeat All mode
Press the Repeat button (5) during playback twice to enable repeat all the track of the CD. And the Rep 1/all/Snooze LED indicator
(18) will light up for a while and then will disappear. Press the Repeat button (5) once more to cancel the repeat mode.
(1) repeat 1 (indicator flashing) (2) repeat all track (indicator light up) (3) off mode
Important: You may press any CD function buttons (play/pause, Skip up /down button) to check the
status of the repeat mode.
CD programming
Up to 20 tracks can be programmed for disc play in any order. Before use, be sure to press the Stop button (11).
1. Set in CD mode & stop the CD playback.
2. Press the Mem/Pre button (12) and “ P01 ” will appear on LED display with flashing Bluetooth/MEM LED indicator (17).
3. Select a desired track by pressing Skip up /down button (10).
4. Press the Mem/Pre button (12) to store the track into memory.
5. Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.
6. When all the desired tracks have been programmed, press Play/Pause button (9) to play the disc in assigned order.
7. Press Stop button (11) to stop playback, press Stop button again to clear all stored memory.
 The programming mode will automatically stop if no button is being pressed in a period of about 10 seconds after pressing the
Mem/Pre button (12). Display will show “FULL” if stored program track is full.
Bluetooth Connection
1. Switch on the unit by pressing the On/Standby button (2), then press Function button (8) to change to “ bt ” (Bluetooth) mode
and the Bluetooth/MEM LED indicator (17) will flash meaning the unit is searching and waiting to connect to Bluetooth.
2. Switch the Bluetooth function of your Bluetooth device on (such as a mobile phone) and select the Bluetooth equipment
code “V50-250” to connect.
3. When the Bluetooth device has connected successfully, the LED display will show “ bt “ and the Bluetooth/MEM LED
indicator (17) will no longer flash but be static.
4. Start playback of the music on your Bluetooth device and enjoy the music through the speakers of this unit.
5. Press the Volume knob (3) to the desired volume level.