Operation Manual

ManualsBrandsGolmar ManualsBackupT1220ML

RÉSOLUTION DES PROBLÈMES

O Rien ne fonctionne.

w Vérifier la tension de sortie entre les bornes ' - ' et ' + ' de l'alimentation. Celle-ci doit être

comprise entre 18Vc.c. Si ce n'est pas le cas, déconnecter l'alimentation de l'installation et

mesurer la tension. Si elle est maintenant correcte, c'est qu'il y a un court-circuit dans

l'installation. Débranchez le transformateur du réseau et vérifiez l'installation.

w Vérifier la polarité du câblage est correct.

w Vérifier le pontet de configuration JP2 de la plaque et le poste/s d'appel sont correctement

configurés, (voir page 19 ).

O Le poste d'appel ne reçoit pas d'appels.

w Vérifier la tension de sortie entre les bornes ' - ' et ' + ' de l'alimentation. Celle-ci doit être

comprise entre 18Vc.c. Si ce n'est pas le cas, déconnecter l'alimentation de l'installation et

mesurer la tension. Si elle est maintenant correcte, c'est qu'il y a un court-circuit dans

l'installation. Débranchez le transformateur du réseau et vérifiez l'installation.

w Vérifier la polarité du câblage est correct.

w Vérifier le pontet de configuration JP2 de la plaque et le poste/s d'appel sont correctement

configurés, (voir page 19 ).

O Volume de la mélodie d'appel dans le poste d'appel n'est pas satisfaisant.

w Vérifiez le réglage de volume d'appel dans le poste d'appel, (voir page 23).

O Le volume audio n'est pas satisfaisant.

w Régler le niveau audio comme expliqué page 19.

O L'intercommunication ne fonctionne pas.

w Rappelez que cette fonction est seulement possible dans des installations avec plus d'un poste

d'appel.

w Vérifiez la fonction d'intercommunication, a été correctement réalisé, (voir page 23).

O La commande de gâche ne fonctionne pas.

w Rappelez que cette fonction est seulement active avec le combiné

w Vérifiez la gâche électrique ainsi que son câblage.

pour la plaque et page 23 pour le poste d'appel

décrocher, sans avoir une

réception d'appel ou durant un procès de communication

Audio

door entry system

kits

2 wires installation

AS-1220 SII

Instructions manual

Cod. 50124519

T1220ML

rev.0213

Summary of content (16 pages)

PAGE 1
T1220ML rev.0213 Audio door entry system kits 2 wires installation AS-1220 SII Instructions manual Cod.
PAGE 2
9 INTRODUCTION First of all we would like to thank and congratulate you for the purchase of this product manufactured by Golmar. The commitment to reach the satisfaction of our customers is stated through the ISO-9001 certification and for the manufacturing of products like this one. Its advanced technology and exacting quality control will do that customers and users enjoy with the legion of features this system offers.
PAGE 3
0 SYSTEM CHARACTERISTICS O O O O O O O O O O O O O O Audio door entry system with simplified installation (polarised 2 wire bus). Up to 1 access door panel. Up to 2 apartments (Necessary setting configuration, see page 33 & 37 for door panel & telephone). Up to 4 telephones per installation. Installations with one apartment, maximum 4 telephones. Installations with two apartments, maximum 2 telephones per apartment. 'Long' acoustic call acknowledgment signals.
PAGE 4
31 DOOR PANEL DESCRIPTION D oor panel description PES-1220. l d g f 1user 2 users Solo abrepuertas de corriente contínua only d.c lock release C NO CV CV P- P+ j h e c k b d i a a. b. c. d. e. f. g. h. i. j. k. l. Screws of fixation of the aluminium front (x2). Call push button for one or two apartments, (see page 39). Label push button. Wall attachment hook (x2). Wiring input hole. Telephone audio adjustment. Door panel audio adjustment. Installation terminals. Microphone. Speaker.
PAGE 5
32 DOOR PANEL INSTALLATION D oor panel positioning. 1850 1450 1650 The upper part of the door panel should be placed at 1,65m. The surface door panel dimensions are the next: . W H D 96 mm. 181 mm. 20 mm. . The door panel has been designed to be placed under most of the environmental conditions. However it's recommended to take additional cautions, like the use of the supplied rainproof cover or the installation under a covered place. R emove the aluminium front.
PAGE 6
33 DOOR PANEL INSTALLATION P lace the door panel. Face the door panel to the wall by placing the top at 1,65m. height and insert the installation wires through the cables entry. 1 user 2 users Drill two holes of 6mm. diameter and insert the wallplugs. Fix the door panel with especified screws. D oor panel wiring. Connect the installation wires to the terminal connector, according to the installation diagrams. c onfiguration jumper 'JP2'.
PAGE 7
34 DOOR PANEL INSTALLATION P ush button label. To costomize the push button label, insert a flat screwdriver to accede to the label, remove the push button front cover, see picture A & B . The label is now accesible to mark a text, see picture C . Replace the push button front cover, making a light pressure until listenning a click in both sides of the front cover, see picture D . A B D C Text Text C lose the door panel. Finish the door panel assembly by replacing the aluminium front.
PAGE 8
35 POWER SUPPLY INSTALLATION D etail of the FA-133 power supply installation and technical features. 3,5 x 25 DIN-7971 The power supply must be installed in a dry and protected place. It's recommended to protect the power supply by using a thermo-magnetic circuit breaker. To install the power supply directly on the wall, drill two holes of Ø6mm. and insert the wallplugs. Fix the transformer with the specified screws.
PAGE 9
36 TELEPHONE DESCRIPTION D escription of the T-1772VD telephone. b d a c a. Telephone handset. b. Speaker grille. c. Microphone hole. d. Subjection hole. e. Telephone cord connectors. f. Door release push button/aux. function. g. Hook switch. h. Intercommunication push button. i. Volume control. e f h i g e F unction push buttons.
PAGE 10
37 TELEPHONE DESCRIPTION C all volume control. MAX The telephone allows to regulate the call volume with a maximum, medium and off value. With the help of the switch of three positions placed in the right front of the telephone. OFF C onfiguration jumper 'JP2'. JP2 Only if the door panel has been configurated for a system of 2 apartments (see page 33), the JP2 configuration jumper of the telephone, allows to link the telephone of the apartment to a call push button of the door panel.
PAGE 11
38 TELEPHONE INSTALLATION F ix the telephone to the wall. It is necessary to open the telephone for wiring and fixing purposes. To open the telephone, insert a plain screwdriver into the slots and gently lever as shown in the drawing. Avoid placing the telephone near sources of heat, in dusty locations or smoky environments. The telephone can be fixed using an electrical embedding box or directly on the wall, as shown on the picture.
PAGE 12
39 INSTALLATION DIAGRAM C onnection to (1 apartment). Apartment 1 T-1772VD T-1772VD JP2 T-1772VD JP2 P+ P- + _ JP2 P+ P- + _ T-1772VD FA-133 JP2 P+ P- + _ P+ P- + _ SEC PRI _ + ~ ~ 230Vc.a. (1) PES-1220 (1) Call push button: JP2 Call to apartment 1. Call to apartment 1. C NO CV CV P- P+ 12Vc.c. * IMPORTANT: Configure the JP2 jumper for one or two apartments (see page 33 for the door panel and page 37 for the telephone). C onnection to (2 apartments).
PAGE 13
40 INSTALLATION DIAGRAM S ections chart. Distance up to 20m. Terminal P+, P- 50m. 1,00mm² _ 1,50mm² CV, CV 1,50mm² +, 100m. 1,50mm² C onnection of an a.c. lock release by using TF-104 transformer and SAR-12/24 relay. PES-1220 TF-104 NC NA C SAR-12/24 SEC PRI IN C NO CV CV P- P+ ~ ~ ~ ~ IN 230Vc.a. C 12Vc.a. onnection of an auxiliary device or control for gate automation. Auxiliary device PES-1220 Control for gate automation PES-1220 TF-104 PRI SEC ~ ~ ~ ~ 230Va.c.
PAGE 14
TROUBLESHOOTING HINTS 41 O Nothing operates. w Check the output power supply voltage between '–' and '+' is of 18Vd.c. Otherwise, disconnect the power supply from the installation and measure again. If its correct now, it means there is a short circuit in the installation. Disconnect the power supply from the mains and check the installation. w Check the polarity wiring.
PAGE 15
42 NOTAS/NOTES
PAGE 16
golmar@golmar.es www.golmar.es Golmar se reserva el derecho a cualquier modificación sin previo aviso. Golmar se réserve le droit de toute modification sans préavis. Golmar reserves the right to make any modifications without prior notice.