Installation Guide

ManualsBrandsGood Earth Lighting ManualsCeiling LightsSmart LED Flat Panel 24-in Brushed Nickel Traditional LED Flush Mount Light

Model / Model / Modelo #: FP1247-AL5-24LFW-G

Required/ Nécessaire/ Obligatorio

Hardware kit* / Trousse de quincaillerie* /

Kit de aditamentos*

DDx3CCx4AAx2 BBx4 EEx4 FFx2

1/8 in.

0,3 cm

GGx1

LED Flat Panel

Panneau plat à DEL

Panel de luces LED plano

Mounting plate

Plaque de montage

Placa de montaje

* Actual hardware may differ from illustration

* La quincaillerie incluse peut être différente de l’illustration.

* Los aditamentos reales pueden diferir de los que se muestran en la ilustración.

Support wire hooks

Crochets des fils de support

Ganchos de alambre de soporte

SAVE AND ATTACH RECEIPT HERE

2 ft. x 2 ft. LED Flat Panel (Page 1)

Panneau plat à DEL de 0,6 m x 0,6 m (Page 2)

Panel plano de luces LED de 0,6 m x 0,6 m (Página 4 )

WARNINGS AND CAUTIONS

WARNING: SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE PANEL

BEFORE REMOVING THE OLD FIXTURE OR INSTALLING A NEW ONE.

SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE

PANEL BEFORE REMOVING THE OLD FIXTURE OR

INSTALLING A NEW ONE.

Read entire installation procedure before you begin and save

instructions for future reference.

THIS FIXTURE IS DIMMABLE USING THE GOOD EARTH LIGHTING APP.

(INSTRUCTION SHEETS INCLUDED)

If unsure if the electrical box is properly grounded, or the box is plastic

and has no ground wire, or are unfamiliar with the methods of properly

grounding fixture, consult a qualified electrician.

IMPORTANT SAFETY INFORMATION

1. Do not look directly at LEDs for extended period of time.

2. For INDOOR use only.

3. Turn power off before servicing.

4. Do not leave bare wires exposed.

5. For electrical requirements, see fixture. Minimum 90°C

supply conductors.

INSTALLATION

Remove mounting plate from LED panel by

sliding into the direction of the slots closest to

the mounting screws (AA), and then lifting up.

Hold the mounting plate up to the junction box

in the desired fixture mounting orientation.

Pull black, white and ground supply wires

from electrical box through the hole in center

of mounting plate. Ground wires can be either

green or bare copper. Attach mounting plate

to the electrical box using mounting screws

(AA) provided.

AAx2

TURN POWER OFF AT BREAKER BOX/FUSE BOX. TURN WALL SWITCH TO JUNCTION BOX OFF

BBx4

CCx4

DDx4

DRYWALLWOOD

Locate the open holes for mounting at the corners of the mounting plate and drill 1/8 in. pilot hole in the center. If a wooden stud is encountered, use the wood screws (BB) and

washers (CC) provided to secure the mounting plate directly to stud.

If no stud is encountered, place the drywall anchors (DD) in the pilot holes and screw them into place until flushed with surface of drywall. Place washer (CC) over the mounting

hole and drive long screws (BB) into drywall anchor until snug. DO NOT OVERTIGHTEN. NOTE: Main support for mounting plate is electrical box when it is secured properly. If

the electrical box is not properly secured, alternative mounting methods such as toggle bolts (not included) should be used to secure mounting plate.

CCx4

1/8 in.

0,3 cm

1/8 in.

0,3 cm

Summary of content (6 pages)

PAGE 1
SAVE AND ATTACH RECEIPT HERE 2 ft. x 2 ft.
PAGE 2
4 3 Hot Neutral EEx3 Ground 3 4 Hold fixture up to secured mounting plate and attach the two support wire hooks from the backside and the one from the front side of fixture to the specially designed slots in the mounting plate to temporarily hold fixture for wiring. Fixture must be properly grounded. Connect fixture ground wire to ground wire in electrical box using a wire nut (EE). Ground wires can be either green or bare copper.
PAGE 3
METTEZ HORS TENSION AU NIVEAU DU DISJONCTEUR OU DU PANNEAU DE FUSIBLES AVANT DE RETIRER L’ANCIEN LUMI- NAIRE OU D’EN INSTALLER UN NOUVEAU. AVERTISSEMENTS ET MISES EN GARDE METTEZ HORS TENSION AU NIVEAU DU DISJONCTEUR OU DU PANNEAU DE FUSIBLES AVANT DE RETIRER L’ANCIEN LUMI- NAIRE OU D’EN INSTALLER UN NOUVEAU. Lisez toute la procédure d’installation avant de commencer, et conservez les instructions en vue de référence future.
PAGE 4
5A 5A 5B 5B Tout en maintenant les crochets des fils de support fixés à la plaque de montage, soulevez le panneau à DEL en faisant attention de ne pas rayer le plafond. Alignez et insérez les 2 languettes métalliques (situées du même côté de la plaque de montage que les fils de support) dans les fentes correspondantes du panneau à DEL. Tout en maintenant les 2 premières languettes métalliques insérées, faites pivoter le panneau vers le haut et insérez les 2 autres languettes du côté opposé.
PAGE 5
DESCONECTE LA ALIMENTACIÓN ELÉCTRICA EN EL PANEL DE CORTACIRCUITOS O DE FUSIBLES ANTES DE RETIRAR EL ACCESORIO DE ILUMINACIÓN VIEJO O INSTALAR UNO NUEVO. ADVERTENCIAS Y PRECAUCIONES DESCONECTE LA ALIMENTACIÓN ELÉCTRICA EN EL PANEL DE CORTACIRCUITOS O DE FUSIBLES ANTES DE RETIRAR EL ACCESORIO DE ILUMINACIÓN VIEJO O INSTALAR UNO NUEVO. INFORMACIÓN DE SEGURIDAD IMPORTANTE Lea todo el procedimiento de instalación antes de comenzar y guarde las instrucciones para referencia futura. 2.
PAGE 6
5A 4 Línea Neutro EEx3 Tierra 4 la caja eléctrica y la placa de montaje utilizando una tuerca para cables (BB). Los cables de conexión a tierra pueden ser verdes o de cobre pelado. Conecte el hilo de suministro negro al cable negro del accesorio para iluminación y el hilo de suministro blanco al cable blanco del accesorio para iluminación, utilizando tuercas para cables (BB). Sujete firmemente las tuercas para cables de manera adecuada para impedir que los cables se aflojen.