User's Manual
the next faster speed settings. During the set up process, LED 1 lights up to indicate for level 1, LED 2 lights up to indicate
for level 2, LED 3 to indicate for level 3, LED 4 lights up to indicate level 4
Flicks the left thumb stick to set up the left thumb stick sensitivity
Flicks the right thumb stick to set up the right thumb stick sensitivity
Once power off, all thumb sticks returns to default with 100% setting
D) Power Management System
The GC2PS3 game pad turns off if it is connected to the PS3 console and is not used for 10 minutes.
The GC2PS3 game pad automatically turns off if it is not connected to the PS3 console for 10 seconds.
To turn off the GC2PS3 game pad, press and hold Home button for 15 seconds to force it to turn off.
To turn on the GC2PS3 game pad, press Home button once. The GC2PS3 game pad turns on and the LED lights.
E) Low battery indication
When the built-in Li-ion battery in low power, the corresponding port LED flashes in 4Hz, and shuts down the motors,
to remind user to recharge the battery.
F) Battery charging indication
When the GC2PS3 game pad is connected to PS3, the corresponding port LED flashes in 1Hz.
When charging is finished, the LED lights on.
When the GC2PS3 game pad is not connected to PS3, the 4 LEDs flash in 1Hz during charging.
The 4 LEDs will be turned off when the charging is finished.
When the GC2PS3 game pad is not connected to PS3 and is connected to a USB port with power only, the 4 LEDs
remains turned off during charging and when charging is completed.
G) Troubleshooting
i) The game pad does not response when another Bluetooth headset is connected to PS3
Please make sure only the GC2PS3 Bluetooth game pad is linked to PS3.
ii) The game pad does not wake up when USB cable is connected
The USB port is for battery charging only. It does not wake up the game pad.
iii) In the BT mode, the USB cable does not improve the wireless interference problem
The USB cable is for battery charging. The wireless data communication with PS3 remains through the Bluetooth.
iv) The thumb stick sensitivity resets to normal during power up
The thumb stick sensitivity reset to default every time the controller is power up
v) The programmed button with turbo feature functions without turbo feature
All buttons programmed with turbo feature are reset to default without turbo during power up
vi) Cannot set up thumb stick sensitivity
To continue the thumb stick sensitivity set up, the [Turbo] button must be pressed and hold during the set up.
The set up process is terminated whenever the [Turbo] button is released.
vii) The Player ID LED indication is incorrect
The LED indicates the Player ID at all times except during the thumb stick sensitivity programming.
During the thumb stick sensitivity set up process, the LED indicates the different sensitivity level.
LED 1 represents normal in 100%. LED 2 represents 1.5 times faster, LED 3 represents 2 times faster, LED 4 epresents
4 times faster.
Left and right thumb sticks sensitivity setting will be indicated through the 4 LEDs separately during the sensitivity set
up process.
viii) The motors do not vibrate during game play.
Please check the LED indication. If it is flashing in 4Hz, then it is in low battery level and motor will not vibrate when
battery is in low level
Warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment
NOTE:THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device
et appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux
deux conditions suivantes: (1)cet appareil ne doit pas provoquer d’interférences et (2)cet appareil doit accepter toute
interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil.
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian
interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.