CAPFA Installation Guide

ManualsBrandsGoodman ManualsEvaporator CoilsAlumaFin7 1.5 Ton, Cased Evaporator Coil (21" W x 21" D x 18" H)

19001 Kermier Rd, Waller, TX 77056

www.goodmanmfg.com

1. ImportantSafetyInstrucons

The following symbols and labels are used throughout this manual

to indicate immediate or potenal safety hazards. It is the owner’s

and installer’s responsibility to read and comply with all safety in-

formaon and instrucons accompanying these symbols. Failure

to heed safety informaon increases the risk of personal injury,

property damage, and/or product damage.

HIGH VOLTAGE!

DISCONNECT ALL POWER BEFORE SERVICING OR

INSTALLING

THIS UNIT. MULTIPLE POWER SOURCES

MAY

BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY

DAMAGE

, PERSONAL INJURY OR DEATH.

ONLY PERSONNEL THAT HAVE BEEN TRAINED TO INSTALL, ADJUST, SERVICE OR

REPAIR (HEREINAFTER

, “SERVICE”) THE EQUIPMENT

SPECIFIED

IN THIS MANUAL

SHOULD SERVICE THE EQUIPMENT. THE MANUFACTURER WILL NOT BE RESPONSIBLE

FOR ANY INJURY OR PROPERTY DAMAGE ARISING FROM IMPROPER SERVICE OR

SERVICE

PROCEDURES. IF

YOU SERVICE THIS

UNIT,

YOU ASSUME

RESPONSIBILITY

FOR ANY INJURY OR PROPERTY DAMAGE

WHICH

MAY RESULT. IN ADDITION,

JURISDICTIONS THAT REQUIRE ONE OR MORE LICENSES TO SERVICE THE EQUIPMENT

SPECIFIED

THIS MANUAL

, ONLY LICENSED

PERSONNEL

SHOULD SERVICE THE

EQUIPMENT. IMPROPER INSTALLATION, ADJUSTMENT, SERVICING OR REPAIR OF

THE EQUIPMENT SPECIFIED IN THIS MANUAL, OR ATTEMPTING TO INSTALL, ADJUST,

SERVICE OR REPAIR

THE EQUIPMENT SPECIFIED IN THIS MANUAL WITHOUT PROPER

TRAINING MAY RESULT IN PRODUCT DAMAGE,

PROPERTY

DAMAGE, PERSONAL

INJURY OR DEATH.

Cancer and Reproducve Harm -

www.P65Warnings.ca.gov

PROP 65 WARNING

FOR CALIFORNIA CONSUMERS

0140M00517-A

WARNING

2. ShippingInspecon

Upon receiving the product, inspect it for damage from shipment.

Shipping damage, and subsequent invesgaon is the responsibility

of the carrier. Verify the model number, specicaons, and accesso-

ries are correct prior to installaon. The distributor or manufacturer

will not accept claims from dealers for transportaon damage or

installaon of incorrectly shipped units.

2.1 Handling

Use cauon when transporng / carrying unit.. Do not carry unit

with hooks or sharp object. The preferred method of carrying

the unit aer arrival at the job site is to carry by two-wheel

hand truck from the back or sides or by hand by carrying at the

cabinet corners.

UPFLOW/DOWNFLOW COILS

INSTALLATION INSTRUCTIONS

3. Codes&Regulaons

This product is designed and manufactured to comply with naonal

codes. Installaon in accordance with such codes and/or prevailing

local codes/regulaons is the responsibility of the installer. The

manufacturer assumes no responsibility for equipment installed

in violaon of any codes or regulaons.

The United States Environmental Protecon Agency(EPA) has

issuedvariousregulaonsregardingtheintroduconanddisposal

ofrefrigerants.Failuretofollowtheseregulaonsmayharmthe

environmentandcanleadtotheimposionofsubstanalnes.

Should you have any quesons please contact the local oce of

the EPA.

4. Replacement Parts

Inspect the unit to verify all required components are present and

intact. Report any missing components immediately to the manu-

facturer or to the distributor. Make sure to include the full product

model number and serial number when reporng and/or obtaining

service parts. Replacement parts for this product are available

through your contractor or local distributor. For the locaon of your

nearest distributor consult the white business pages, the yellow

page secon of the local telephone book or contact:

HOMEOWNER SUPPORT

GOODMAN MANUFACTURING COMPANY, L.P.

19001 KERMIER ROAD

WALLER, TEXAS 77484

877– 254 – 4729

5. Pre-InstallaonInstrucons

5.1Preparaon

Keep this document with the unit. Carefully read all instrucons

for the installaon prior to installing product. Make sure each

step or procedure is understood and any special consideraons

are taken into account before starng installaon. Assemble all

tools, hardware and supplies needed to complete the installa-

on. Some items may need to be purchased locally. Make sure

everything needed to install the product is on hand before

starng.

5.2 Clearances

Refrigerant lines must be routed depending on conguraon

of unit to maintain the required 24” minimum clearance for

service. Consult all appropriate regulatory codes prior to deter-

mining nal clearances. In installaons that may lead to physical

damage (i.e. a garage) it is advised to install a protecve barrier

to prevent such damage. Always install units such that a posive

slope in condensate line (1/4” per foot) is allowed.

IOG-4010C

03/2020

Summary of content (8 pages)

PAGE 1
UPFLOW/DOWNFLOW COILS INSTALLATION INSTRUCTIONS 1. Important Safety Instructions 3. Codes & Regulations The following symbols and labels are used throughout this manual to indicate immediate or potential safety hazards. It is the owner’s and installer’s responsibility to read and comply with all safety information and instructions accompanying these symbols. Failure to heed safety information increases the risk of personal injury, property damage, and/or product damage.
PAGE 2
6. Application Information If the uncased coil is to be installed on top of a gas furnace, allow enough space between the top to the furnace and the bottom of the plastic coil drain pan to have a free flow of air. A minimum of 2.0” distance from the top of the furnace and the bottom of the coil pan is required. NOTE: The coil must be installed with the line set and drain openings to the front of the furnace.
PAGE 3
9.3 Brazing Braze joints should be made only with the connections provided external to the cabinet. Do not alter the cabinet nor braze inside the cabinet. To avoid overheating after brazing, quench all brazed joints with water or a wet rag. APPLYING TOO MUCH HEAT TO ANY TUBE CAN MELT THE TUBE. TORCH A CHASSIS WITH 80% HEAT REQUIRED TO BRAZE TUBES OF VARIOUS SIZES MUST BE PROPORTIONAL TO THE SIZE OF THE TUBE. SERVICE PERSONNEL MUST USE THE APPROPRIATE HEAT LEVEL FOR THE SIZE OF THE TUBE BEING BRAZED.
PAGE 4
10. Supply Duct Connection 8. AFTER THE TAILPIECE HAS COOLED, confirm position of the white Teflon® seal and hand tighten the 13/16 nut. 1. Top flanges can be bent for ease in installation to the duct flanges. (See Figure 6) CAUTION EXCESSIVE TORQUE CAN CAUSE ORIFICES TO STICK. USE THE PROPER TORQUE SETTINGS WHEN TIGHTENING ORIFICES. 9. Torque the 13/16” nut to 10-20 ft-lbs. or 1/6 turn past hand tight. Unfolded View 10. Replace suction line grommet and insulation. Top Flange Detail View 9.
PAGE 5
12. Sealing Along The Panel Gap 2. A duct flange kit can also be purchased from your distributor. (See Figure 7) IMPORTANT NOTE: To prevent cabinet sweating and airflow leak, apply field provided insulation tape along all joining surfaces between the coil, gas furnace, duct work and panels. See Figure 8. • 14 inch chassis - CLDUCTFLGA • 17.5 inch chassis - CLDUCTFLGB • 21 inch chassis - CLDUCTFLGC • 24.5 inch chassis - CLDUCTFLGD Apply Insulation Tape 13.
PAGE 6
THIS PAGE WAS LEFT BLANK INTENTIONALLY 6
PAGE 7
THIS PAGE WAS LEFT BLANK INTENTIONALLY 7
PAGE 8
CUSTOMER FEEDBACK We are very interested in all product comments. Please fill out the feedback form on one of the following links: Goodman® Brand Products: (http://www.goodmanmfg.com/about/contact-us). Amana® Brand Products: (http://www.amana-hac.com/about-us/contact-us). You can also scan the QR code on the right for the product brand you purchased to be directed to the feedback page. PRODUCT REGISTRATION Thank you for your recent purchase.