CAPFA Installation Manual

ManualsBrandsGoodman ManualsEvaporator CoilsAlumaFin7 1.5 Ton, Cased Evaporator Coil (21" W x 21" D x 18" H)

5151 San Felipe, Suite 500, Houston, TX 77056

1. Important Safety Instructions

The following symbols and labels are used throughout this

manual to indicate immediate or potential safety hazards. It is

the owner’s and installer’s responsibility to read and comply with

all safety information and instructions accompanying these sym-

bols. Failure to heed safety information increases the risk of

personal injury, property damage, and/or product damage.

HIGH VOLTAGE!

ISCONNECT

ALL

POWER

BEFORE

SERVICING

INSTALLING

THIS

UNIT

. M

ULTIPLE

POWER

SOURCES

MAY

PRESENT

. F

AILURE

MAY

CAUSE

PROPERTY

DAMAGE

PERSONAL

INJURY

DEATH

NLY

PERSONNEL

THAT

HAVE

BEEN

TRAINED

INSTALL

ADJUST

SERVICE

REPAIR

(

HEREINAFTER

, “

SERVICE

”)

THE

EQUIPMENT

SPECIFIED

THIS

MANUAL

SHOULD

SERVICE

THE

EQUIPMENT

. T

MANUFACTURER

WILL

NOT

RESPONSIBLE

FOR

ANY

INJURY

PROPERTY

DAMAGE

ARISING

FROM

IMPROPER

SERVICE

PROCEDURES

. I

YOU

SERVICE

THIS

UNIT

YOU

ASSUME

RESPONSIBILITY

FOR

ANY

INJURY

PROPERTY

DAMAGE

WHICH

MAY

RESULT

. I

ADDITION

JURISDICTIONS

THAT

REQUIRE

ONE

LICENSES

SERVICE

THE

EQUIPMENT

SPECIFIED

THIS

MANUAL

ONLY

LICENSED

PERSONNEL

SHOULD

SERVICE

THE

EQUIPMENT

. I

MPROPER

INSTALLATION

ADJUSTMENT

SERVICING

REPAIR

THE

EQUIPMENT

SPECIFIED

THIS

MANUAL

ATTEMPTING

INSTALL

ADJUST

SERVICE

REPAIR

THE

EQUIPMENT

SPECIFIED

THIS

MANUAL

WITHOUT

PROPER

TRAINING

MAY

RESULT

PRODUCT

DAMAGE

PROPERTY

DAMAGE

PERSONAL

INJURY

DEATH

2. Shipping Inspection

Upon receiving the product, inspect it for damage from shipment.

Shipping damage, and subsequent investigation is the responsi-

bility of the carrier. Verify the model number, specifications,

and accessories are correct prior to installation. The distributor

or manufacturer will not accept claims from dealers for trans-

portation damage or installation of incorrectly shipped units.

2.1 Handling

Use caution when transporting / carrying unit.. Do not carry

unit with hooks or sharp object. The preferred method of

carrying the unit after arrival at the job site is to carry by two-

wheel hand truck from the back or sides or by hand by carry-

ing at the cabinet corners.

3. Codes & Regulations

This product is designed and manufactured to comply with na-

tional codes. Installation in accordance with such codes and/or

prevailing local codes/regulations is the responsibility of the in-

staller. The manufacturer assumes no responsibility for equip-

ment installed in violation of any codes or regulations.

UPFLOW/DOWNFLOW COILS

INSTALLATION INSTRUCTIONS

The United States Environmental Protection Agency (EPA) has

issued various regulations regarding the introduction and dis-

posal of refrigerants. Failure to follow these regulations may

harm the environment and can lead to the imposition of sub-

stantial fines. Should you have any questions please contact the

local office of the EPA.

4. Replacement Parts

Inspect the unit to verify all required components are present

and intact. Report any missing components immediately to the

manufacturer or to the distributor. Make sure to include the full

product model number and serial number when reporting and/

or obtaining service parts. Replacement parts for this product

are available through your contractor or local distributor. For

the location of your nearest distributor consult the white busi-

ness pages, the yellow page section of the local telephone book

or contact:

HOMEOWNER SUPPORT

GOODMAN MANUFACTURING COMPANY, L.P.

19001 KERMIER ROAD

WALLER, TEXAS 77484

877– 254 – 4729

5. Pre-Installation Instructions

5.1 Preparation

Keep this document with the unit. Carefully read all instruc-

tions for the installation prior to installing product. Make sure

each step or procedure is understood and any special consid-

erations are taken into account before starting installation.

Assemble all tools, hardware and supplies needed to com-

plete the installation. Some items may need to be purchased

locally. Make sure everything needed to install the product is

on hand before starting.

5.2 Clearances

Refrigerant lines must be routed depending on configuration

of unit to maintain the required 24” minimum clearance for

service. Consult all appropriate regulatory codes prior to de-

termining final clearances. In installations that may lead to

physical damage (i.e. a garage) it is advised to install a protec-

tive barrier to prevent such damage. Always install units such

that a positive slope in condensate line (1/4" per foot) is al-

lowed.

6. Application Information

Coils are designed for indoor installation only and must be in-

stalled downstream (discharge air) of the furnace. The CAPF/CAPT

product line may be installed in upflow or downflow orienta-

tions.

IO-284H

02/2018

Summary of content (8 pages)

PAGE 1
UPFLOW/DOWNFLOW COILS INSTALLATION INSTRUCTIONS 1. Important Safety Instructions The following symbols and labels are used throughout this manual to indicate immediate or potential safety hazards. It is the owner’s and installer’s responsibility to read and comply with all safety information and instructions accompanying these symbols. Failure to heed safety information increases the risk of personal injury, property damage, and/or product damage.
PAGE 2
7. Condensate Drain Piping 8.1 Tubing Size/Length In all cooling applications where condensate overflow may cause damage, a secondary drain pan must be provided by the installer and placed under the entire unit with a separate drain line properly sloped and terminated in an area visible to the owner. This secondary drain pan can provide extra protection to the area under the unit should the primary drain plug up and overflow.
PAGE 3
LIQUID LINE RUBBER GROMMET LIQUID LINE SET Figure 2.2 5. Insert liquid line set into liquid tube expansion and slide grommet about 18" away from braze joint. Figure 1 6. Insert suction line set into suction tube expansion and slide insulation and grommet about 18" away from braze joint. 7. Insert the suction line into the connection, slide the insulation and the rubber grommet at least 18" away from the braze joint. Braze both liquid and suction line joints. 7. Braze suction and liquid line joints. 9.
PAGE 4
11. Plastic Drain Pan Application 2” MIN. DO NOT USE THE COIL PAN SHIPPED WITH THE UNIT ON OIL FURNACES OR ANY APPLICATION WHERE THE TEMPERATURE OF THE DRAIN PAN MAY EXCEED 300°F. A HIGH TEMPERATURE DRAIN PAN SUCH AS KITS HTP-A, -B, -C AND -D FOR NORMAL CABINET WIDTHS OF 14, 17.5, 21 AND 24.5 INCHES, RESPECTIVELY, SHOULD BE USED FOR APPLICATIONS WHERE THE TEMPERATURE EXCEEDS 300°F AND BELOW 450°F. A FIELD FABRICATED METAL DRAIN PAN CAN ALSO BE USED FOR APPLICATIONS WHERE TEMPERATURE EXCEEDS 300°F.
PAGE 5
THIS PAGE WAS LEFT BLANK INTENTIONALLY 5
PAGE 6
THIS PAGE WAS LEFT BLANK INTENTIONALLY 6
PAGE 7
THIS PAGE WAS LEFT BLANK INTENTIONALLY 7
PAGE 8
CUSTOMER FEEDBACK We are very interested in all product comments. Please fill out the feedback form on one of the following links: Goodman® Brand Products: (http://www.goodmanmfg.com/about/contact-us). Amana® Brand Products: (http://www.amana-hac.com/about-us/contact-us). You can also scan the QR code on the right for the product brand you purchased to be directed to the feedback page. PRODUCT REGISTRATION Thank you for your recent purchase.