Installation Guide

ManualsBrandsGoodman ManualsCooling & Air Quality120,000 BTU 96% AFUE Single Stage Gas Furnace - Downflow/Horizontal

5151 San Felipe Suite 500

Houston, TX 77056

www.goodmanmfg.com • www.amana-hac.com







Installer:

Ax all manuals

adjacent to the unit.

s a professional installer you have an obligation to know

the product better than the customer. This includes all

safety precautions and related items.

Prior to actual installation, thoroughly familiarize yourself

with this Instruction Manual. Pay special attention to all

safety warnings. Often during installation or repair it

is possible to place yourself in a position which is more

hazardous than when the unit is in operation.

Remember, it is your responsibility to install the product

safely and to know it well enough to be able to instruct a

customer in its safe use.

Safety is a matter of common sense...a matter of thinking



safety practices...follow them.

The precautions listed in this Installation Manual are

intended as supplemental to existing practices. However,



the content of this manual, the precautions listed here

take precedence.





*NOTE: Please contact your distributor or our website



manual.

Brand is a registered trademark of Maytag Corporation or its related companies

IOG-2020B

7/2019

TABLE OF CONTENTS

 ..................................... 3

 ....................................... 5

 ........... 5

 ........................................... 5

 ........................................ 5

 ............... 6

 ............................ 8

 ............................... 8

 ..................................... 8

 ............ 8

 .....................................10

 .............10

 ......................................10

 ........10

 ....................................10

 ...................................................10

 ....11

 ..................................................11

 .......................................11

 ..............11

 ..................12

 ........12

 ........................12

-

 ........................................................13

 ..................................13

-

 ......................................................14

NLY

PERSONNEL

THAT

HAVE

BEEN

TRAINED

INSTALL

ADJUST

SERVICE

REPAIR

(

HEREINAFTER

, “

SERVICE

”)

THE

EQUIPMENT

SPECIFIED

THIS

MANUAL

SHOULD

SERVICE

THE

EQUIPMENT

. T

MANUFACTURER

WILL

NOT

RESPONSIBLE

FOR

ANY

INJURY

PROPERTY

DAMAGE

ARISING

FROM

IMPROPER

SERVICE

PROCEDURES

. I

YOU

SERVICE

THIS

UNIT

YOU

ASSUME

RESPONSIBILITY

FOR

ANY

INJURY

PROPERTY

DAMAGE

WHICH

MAY

RESULT

. I

ADDITION

JURISDICTIONS

THAT

REQUIRE

ONE

LICENSES

SERVICE

THE

EQUIPMENT

SPECIFIED

THIS

MANUAL

ONLY

LICENSED

PERSONNEL

SHOULD

SERVICE

THE

EQUIPMENT

. I

MPROPER

INSTALLATION

ADJUSTMENT

SERVICING

REPAIR

THE

EQUIPMENT

SPECIFIED

THIS

MANUAL

ATTEMPTING

INSTALL

ADJUST

SERVICE

REPAIR

THE

EQUIPMENT

SPECIFIED

THIS

MANUAL

WITHOUT

PROPER

TRAINING

MAY

RESULT

PRODUCT

DAMAGE

PROPERTY

DAMAGE

PERSONAL

INJURY

DEATH









These furnaces comply with requirements

embodied in the American National Stan-

dard / National Standard of Canada ANSI



Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

PROP 65 WARNING

FOR CALIFORNIA CONSUMERS

0140M00517-A

Summary of content (52 pages)

PAGE 1
Installation Instructions for *MES9* & *CES9* Single-Stage Gas Furnace (Type FSP CATEGORY IV Direct or Non Direct Vent Air Furnace) (Type FSP CATÉGORIE IV Direct ou four á air soufflé non direct) These furnaces comply with requirements embodied in the American National Standard / National Standard of Canada ANSI Z21.47·CSA-2.3 Gas Fired Central Furnaces.
PAGE 2
Standard Furnace Connections.........................14 Vent/Flue Pipe............................................14 Combustion Air Pipe.........................................15 Direct Vent Installations................................15 Non-Direct Vent Installations..........................15 Alternate Vent/Flue Location..........................16 Alternate Combustion Air Provision...................16 Non-Direct Vent (Single Pipe) Piping..................17 Vent/Flue Pipe Terminations.................
PAGE 3
Safety Considerations WARNING Adhere to the following warnings and cautions when installing, adjusting, altering, servicing, or operating the furnace. To ensure proper installation and operation, thoroughly read this manual for specifics pertaining to the installation and application of this product. TO PREVENT PERSONAL INJURY OR DEATH DUE TO IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE, REFER TO THIS MANUAL .
PAGE 4
WARNING FIRE OR EXPLOSION HAZARD Failure to follow the safety warnings exactly could result in serious injury, death or property damage. Never test for gas leaks with an open flame. Use a commercially available soap solution made specifically for the detection of leaks to check all connections. A fire or explosion may result causing property damage, personal injury or loss of life.
PAGE 5
Shipping Inspection 1. Disconnect all power to the furnace. Do not touch the integrated control module or any wire connected to the control prior to discharging your body’s electrostatic charge to ground. 2. Firmly touch a clean, unpainted, metal surface of the furnaces near the control. Any tools held in a person’s hand during grounding will be discharged. 3. Service integrated control module or connecting wiring following the discharge process in step 2.
PAGE 6
Dual certification means that the combustion air inlet pipe is optional and the furnace can be vented as a: Non-direct vent (single pipe) central forced air furnace in which combustion air is taken from the installation area or from air ducted from the outside or, Direct vent (dual pipe) central forced air furnace in which all combustion air supplied directly to the furnace burners through a special air intake system outlined in these instructions.
PAGE 7
• • • • • • • locations and to determine if the piping system from furnace to termination can be accomplished within the guidelines given. NOTE: The length of flue and/or combustion air piping can be a limiting factor in the location of the furnace. Locate the furnace so condensate flows downwards to the drain. Do not locate the furnace or its condensate drainage system in any area subject to below freezing temperatures without proper freeze protection.
PAGE 8
NOTE: In addition to the required clearances to combustible materials, a minimum of 24 inches service clearance must be available in front of the unit. *MES[92 & 96]* MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS (INCHES) POSITION* Upflow Horizontal SIDES 0" 6" REAR 0" 0" FRONT 3" 3" BOTTOM C C FLUE 0" 0" TOP 1" 6" A furnace installed in a confined space (i.e., a closet or utility room) must have two ventilation openings with a total minimum free area of 0.
PAGE 9
WARNING AVERTISSEMENT CARBON MONOXIDE POISONING HAZARD Failure to follow the steps outlined below for each appliance connected to the venting system being placed into operation could result in carbon monoxide poisoning or death. RISQUE D'INTOXICATION AU MONOXYDE DE CARBONE Si les étapes décrites ci-dessous ne sont pas suivies pour chacun des appareils raccordés au système de ventilation au moment de sa mise en marche, cela peut entraîner une intoxication au monoxyde de carbone ou la mort.
PAGE 10
House depressurization can cause back drafting or improper combustion of gas-fired appliances, thereby exposing building occupants to gas combustion products that could include carbon monoxide. When installing a furnace horizontally, additional consideration must be given to the following: Furnace Suspension If suspending the furnace from rafters or joists, use 3/8” threaded rod and 2”x2”x1/8” angle iron as shown in the following diagram.
PAGE 11
Pipe and Combustion Air Pipe for details concerning the conversion to the alternate vent/flue and combustion air connections. Drain Pan A drain pan must be provided if the furnace is installed above a conditioned area. The drain pan must cover the entire area under the furnace (and air conditioning coil if applicable). When using the horizontal alternate vent configuration, you must use the RF000142 vent drain kit. See following illustration.
PAGE 12
Vent/Flue Pipe & Combustion Air Pipe Dual Certification: Non-Direct/Direct Vent This manual will refer to the pipe that discharges products of combustion to the outdoors as the “vent” pipe or “flue” pipe. The pipe that supplies air for combustion to the furnace will be referred to as the “intake” pipe or “combustion air” pipe.
PAGE 13
Proper Vent/Flue and Combustion Air Piping Practices Adhere to these instructions to ensure safe and proper furnace performance. The length, diameter, and number of elbows of the vent/flue pipe and combustion air pipe (when applicable) affects the performance of the furnace and must be carefully sized. All piping must be installed in accordance with local codes and these instructions.
PAGE 14
NOTE: Refer to Location Requirements and Considerations for combustion air contaminant restrictions. For Canadian installations, ABS may be used as a combustion air pipe only. ABS is not an approved vent material in Canada. If ABS is used as a combustion air pipe, it must be CSA certified. Always follow the manufacturer’s instructions in the use of primer and cement. Do not use primer and cement around potential sources of ignition. Do not use primer or cement beyond its expiration date.
PAGE 15
This joint can be rotated on the fitting to establish maximum clearance between refrigerant lines, metering devices, and condensate drain lines, etc. This joint is the equivalent of one 90 deg. elbow when considering elbow count. VENT-DRAIN NOTE: For non-direct vent installations, a minimum of one 90° elbow should be installed on the combustion air intake coupling to guard against inadvertent blockage.
PAGE 16
Alternate Vent/Flue Location *MES92 Direct Vent (2-Pipe) and Non-Direct Vent (1-Pipe) (6) Maximum Allowable Length of Vent/Flue Pipe (1) (2) Number of Elbows (3) (5) The alternate vent/flue location is the large hole directly in line with the induced draft blower outlet. To use the alternate vent/flue location refer to the following steps and the “Alternate Vent/Flue Location” figure. This option is not available with counterflow models.
PAGE 17
*MES96 / *CES96 Direct Vent (2-Pipe) and Non-Direct Vent (1-Pipe) (6) Maximum Allowable Length of Vent/Flue Pipe (1) (2) Number of Elbows (3) (5) PIPE MODEL 1 2 3 4 5 6 7 SIZE (4) *MES960403AN *MES960603BN *MES960803BN *MES960804CN *MES960805CN *MES961004CN *MES961005CN *MES961205DN *CES960603BN *CES960804CN *CES961005CN *CES961205DN Vent/Flue Pipe Terminations NOTE: If either a 90 degree or 45 degree elbow is used for termination, it must be pointed downward.
PAGE 18
10”- 24” TEE (OPTIONAL) COMBUSTION AIR INTAKE (OPTIONAL) *Not required for single pipe installation RO OF 6” MAX 12” MIN HEIGHT DIFFERENCE 4” MIN E LIN 96 12” MIN TO ROOF OR HIGHEST ANTICIPATED SNOW LEVEL AX ”M .- 3 I ”M 90º OR 45° ELBOW N. 12" MIN. TO GRADE OR HIGHEST ANTICIPATED SNOW LEVEL Figure 12 Standard Horizontal Terminations (Dual Pipe) Figure 15 Direct Vent (Dual Pipe) Piping ELBOWS Direct vent installations require both a combustion air intake and a vent/flue pipe.
PAGE 19
Vent/Flue and Combustion Air Pipe Terminations 90° ELBOWS The vent/flue and combustion air pipes may terminate vertically, as through a roof, or horizontally, as through an outside wall. Vertical pipe terminations should be as shown in the following figure. Refer to Vent/Flue Pipe and Combustion Pipe - Termination Locations for details concerning location restrictions. The penetrations through the roof must be sealed tight with proper flashing such as is used with a plastic plumbing vent.
PAGE 20
NOTE: In vertical installations, air conditioning coil condensate may drain into the furnace trap as long as there is a trap between the coil and the furnace trap and the drain pipe is not terminating below the water level of the furnace trap. H oriz ontal Ins tallation Ve rtica l Ins tallation Side Wall Vent Kit Figure 19 #2 #1 #3 Concentric Vent Termination Refer to the directions provided with the Concentric Vent Kit (DCVK) for installation specifications.
PAGE 21
Acceptable area for drain hole. Side Cut-Out 12” Hose #1 Hose #2 3” Right side shown. Figure 21 Field Supplied Drain 45 degree barb-pipe adapter Drain the furnace and air conditioning coil if applicable, in compliance with code requirements. In horizontal or counterflow installations, a field installed rubber coupling will allow the drain trap to be removed for cleaning. The drain trap must be primed before initial furnace start up.
PAGE 22
Upflow Model Installed Horizontally with Left Side Down Minimum 5 1/2” clearance is required for the drain trap beneath the furnace. Hose #11 *Also see Front Cover Pressure Switch Tube Location on page 10. 1. Remove the clamps from the two drain tubes on the trap. 2. Remove the two screws holding the drain trap to the blower deck. 3. Remove the trap and hoses from the blower deck.
PAGE 23
11. (Draining the Collector Box) Remove cap from left side collector box drain port (bottom in horizontal left position) and install it on right side (top) collector box drain port. 12. Install the non-grommet end of hose #11 from outside the cabinet in the upper drain hole. Install on collector box and secure with a silver clamp. 13. Use two silver clamps and secure the hoses to drain trap. The trap outlet faces the front of the furnace.
PAGE 24
Drain Exiting Right Side (See Figure 27) WARNING 1. Remove hose clamps and hoses from trap. 2. Remove trap. 3. (Draining the Vent Elbow) Insert the non-grommet end hose #10 into the cabinet back drain hole. Insert a coupling into the drip leg of the vent-drain elbow and secure with a silver clamp. Secure hose #10 on vent drain elbow barb fitting with a silver clamp. 4.
PAGE 25
1. Remove the factory installed drain trap and hose assemblies. Leave the 100° elbow inserted and clamped in the vent-drain elbow. 2. Remove two 1”plugs from left side of cabinet 3. (Draining the Collector Box) Remove the cap from the left side of the collector box drain port (bottom in horizontal left position) and install it on right side drain port. 4. Place radius end of hose #4 (factory installed) on the collector box drain port and secure with a silver clamp. 5.
PAGE 26
module electronic air cleaner terminals EAC-H is energized with 115 volts whenever the circulator blower is energized. NOTE: Wire routing must not to interfere with circulator blower operation, filter removal, or routine maintenance. WARNING EDGES OF SHEET METAL HOLES MAY BE SHARP. USE GLOVES AS A PRECAUTION WHEN REMOVING HOLE PLUGS. WARNING TO PREVENT PERSONAL INJURY OR DEATH DUE TO ELECTRIC SHOCK, 120 HUM-H EAC-H DISCONNECT ELECTRICAL POWER BEFORE INSTALLING OR SERVICING THIS UNIT.
PAGE 27
Twinning 3. Relocate junction box and associated plugs and grommets to opposite side panel. Secure with screws removed in step Furnaces may be twinned without the use of a twinning kit. Furnaces must be the same model and equipped with PCBBF145 control boards. Follow the diagram provided in this manual. Connection of the “twin” terminals of each control together will allow simultaneous operation of two or more furnace indoor blowers to operate synchronously on a common duct system.
PAGE 28
not be exceeded to prevent unit overfiring. Procedure & Adjustment for use of this control during start up and shut down periods. WARNING Gas Piping Connections TO AVOID POSSIBLE UNSATISFACTORY OPERATION OF EQUIPMENT DAMAGE DUE TO UNDERFIRING OR EQUIPMENT, USE THE PROPER SIZE OF NATURAL /PROPANE GAS PIPING NEEDED WHEN RUNNING PIPE FROM THE METER/TANK TO THE FURNACE.
PAGE 29
TWINNING CONNECTION DIAGRAM 595240 REV.
PAGE 30
Alternate Gas Line Location Manifold Burners Gas Valve Manual Shut Off Valve (upstream from ground joint pipe union) Alternate Union Location *Ground Joint Pipe Union *Ground Joint Pipe Union Grommet in Standard Gas Line Hole Manual Shut Off Valve (upstream from ground joint pipe union) Drip Leg Plug in Alternate Gas Line Hole Drip Leg Grommet in Standard Gas Line Hole Burners *NOTE: Union may be inside furnace cabinet where allowed by local codes.
PAGE 31
Check for leaks using an approved chloride-free soap and water solution, an electronic combustible gas detector, or other approved testing methods. For satisfactory operation, propane gas pressure must be 10” WC at the furnace manifold with all gas appliances in operation. Maintaining proper gas pressure depends on three main factors: 1. Vaporization rate, depending on temperature of the liquid, and “wetted surface” area of the container or containers. 2. Proper pressure regulation.
PAGE 32
external static pressure. The supply duct pressure must be read between the furnace and the cooling coil. This reading is usually taken by removing the “A” shaped block off plate from the end on the coil; drilling a test hole in it and reinstalling the block off plate. Take a duct static reading at the test hole. Tape up the test hole after your test is complete. The negative pressure must be read between the filter and the furnace blower.
PAGE 33
better filtration to protect equipment and the air distribution system than a standard 1” filter and often has lower static pressure loss than a 1” filter. Also a deep-pleated filter will typically require less frequent replacement intervals. Avoid using highly restrictive 1” filters which produce static pressure loss greater than .25” W.C. In some installations the minimum filter size required (consult filter sizing chart above) will not lend itself to a filter installation on the side of the furnace.
PAGE 34
sealant compound or other suitable method to prevent air leakage. For optimal performance verify that all do gaskets are properly in place and replace as needed to prevent air leakage. Drain Trap Priming The drain trap MUST be primed prior to furnace startup. To prime, fill both sides of the drain trap with water. This ensures proper furnace drainage upon startup and prohibits the possibility of flue gases escaping through the drain system. Furnace Operation Purge gas lines of air prior to startup.
PAGE 35
The integrated control will close the gas valve and extinguish flame. Following a 15 second delay, the induced draft blower will be de-energized. The indoor blower will shut down when the time delay expires (selectable on 96% models). 2. Remove the burner compartment door and move the furnace gas valve manual control to the OFF position. 3. Close the manual gas shutoff valve external to the furnace. 4. Replace the burner compartment door.
PAGE 36
6. Turn on power and close thermostat “R” and “W” contacts to provide a call for heat. 7. Measure the gas manifold pressure with burners firing. Adjust manifold pressure using the Manifold Gas Pressure table shown on this page. 8. Remove regulator cover screw from the outlet pressure regulator adjust tower and turn screw clockwise to increase pressure or counterclockwise to decrease pressure. Replace regulator cover screw. 9. Turn off all electrical power and gas supply to the system. 10.
PAGE 37
Circulator Blower Speeds Blower Heat Off Delay Timings This furnace is equipped with a multi-speed circulator blower. This blower provides ease in adjusting blower speeds. The Specification Sheet applicable to your model provides an airflow table, showing the relationship between airflow (CFM) and external static pressure (E.S.P.), for the proper selection of heating and cooling speeds. The integrated control module on 96% models provides a selectable heat off delay function.
PAGE 38
• • • • • • • • Outdoor fan and compressor are energized. Circulator blower is energized on the cool speed. 96% models 115 VAC EAC terminal is energized. Furnace circulator blower and outdoor cooling unit run their appropriate speeds, integrated control module monitors safety circuits continuously. R,Y, G thermostat contacts open, completing the call for cool. Outdoor fan and compressor are de-energized. Circulator blower continues running during a cool off delay period of 65 seconds.
PAGE 39
Diagnostic Chart Maintenance Refer to the Diagnostic Codes chart for assistance in determining the source of unit operational problems. Annual Inspection The furnace should be inspected by a qualified installer, or service agency at least once per year. This check should be performed at the beginning of the heating season. This will ensure that all furnace components are in proper working order and that the heating system functions appropriately. Pay particular attention to the following items.
PAGE 40
Media Air Filter or Electronic Air Cleaner Removal Flame Sensor (Qualified Servicer Only) Follow the manufacturer’s directions for service. Under some conditions, the fuel or air supply can create a nearly invisible coating on the flame sensor. This coating acts as an insulator causing a drop in the flame sense signal. If the flame sense signal drops too low the furnace will not sense flame and will lock out.
PAGE 41
Troubleshooting Chart PCBBF145 Symptoms of Abnormal Operation • Furnace fails to operate. Associated Fault Description(s) Possible Causes LED Code2 NONE • Integrated control module diagnostic LED provides no signal. • No 115 volt power to furnace, or no 24 volt power to integrated control module. • Blown fuse or circuit breaker. • Integrated control module has an internal fault. • Manual disconnect switch OFF, door switch open, or 24 volt wires improperly connected or loose.
PAGE 42
Troubleshooting Chart Symptoms of Abnormal Operation • Circulator blower runs continuously. No furnace operation. • Integrated control module diagnostic LED is flashing FOUR (4) flashes. Associated Fault Description(s) LED Code2 4 4 FLASHES • Induced draft blower and circulation blower runs continuously. No furnace operation. 5 • Integrated control module diagnostic LED is flashing FIVE (5) flashes. 5 FLASHES • Furnace fails to operate.
PAGE 43
*MES92*** Heating Airflow DIP SWITCHE S S2-1 , OFF OFF GMES92 ON OFF* / 0403A ON ON** AMES92 OFF ON** OFF OFF** GMES92 ON OFF* / 0603B ON ON AMES92 OFF ON** OFF OFF GMES92 ON OFF* / 0803B ON ON AMES92 OFF ON OFF OFF** GMES92 ON OFF* / 0804C ON ON** AMES92 OFF ON** OFF OFF** GMES92 ON OFF* / 0805C ON ON** AMES92 OFF ON** OFF OFF** GMES92 ON OFF* / 1004C ON ON AMES92 OFF ON** OFF OFF** GMES92 ON OFF* / 1005C ON ON AMES92 OFF ON** OFF OFF** GMES92 ON OFF* / 1205D ON ON** AMES92 OFF ON * Default & Recommended
PAGE 44
*MES92*** Circulation Airflow DIP SWITCHES MODEL S2-3 , S2-4 OFF OFF* ON OFF 0403A OFF ON ON ON OFF OFF* GMES92 ON OFF / 0603B OFF ON AMES92 ON ON OFF OFF* GMES92 ON OFF / 0803B OFF ON AMES92 ON ON OFF OFF* GMES92 ON OFF / 0804C OFF ON AMES92 ON ON OFF OFF* GMES92 ON OFF / 0805C OFF ON AMES92 ON ON OFF OFF* GMES92 ON OFF / 1004C OFF ON AMES92 ON ON OFF OFF* GMES92 ON OFF / 1005C OFF ON AMES92 ON ON OFF OFF* GMES92 ON OFF / 1205D OFF ON AMES92 ON ON * Default & Recommended GMES92 / AMES92 0.
PAGE 45
*MES92*** Cooling Airflow GMES92 / AMES92 GMES92 / AMES92 GMES92 / AMES92 GMES92 / AMES92 GMES92 / AMES92 GMES92 / AMES92 GMES92 / AMES92 GMES92 / AMES92 * Default DIP SWITCHES MODEL S1-1 , S1-2 , S13 OFF OFF OFF OFF ON ON ON OFF ON ON ON ON 0403A ON OFF OFF ON ON OFF OFF ON OFF OFF OFF ON* OFF OFF OFF OFF ON ON ON OFF ON ON ON ON 0603B ON OFF OFF ON ON OFF OFF ON OFF OFF OFF ON* OFF OFF OFF OFF ON ON ON OFF ON ON ON ON 0803B ON OFF OFF ON ON OFF OFF ON OFF OFF OFF ON* OFF OFF OFF OFF ON ON ON OFF
PAGE 46
Heating Airflow MODEL GCES96/ ACES96/ VCES96 0403B GCES96/ ACES96/ VCES96 0603B GCES96/ ACES96/ VCES96 0804C GCES96/ ACES96/ VCES96 1005C GCES96/ ACES96/ VCES96 1205D GMES96/ AMES96/ VMES96 0403A GMES96/ AMES96/ VMES96 0603B GMES96/ AMES96/ VMES96 0803B GMES96/ AMES96/ VMES96 0804C GMES96/ AMES96/ VMES96 0805C GMES96/ AMES96/ VMES96 1005C GMES96/ AMES96/ VMES96 1205D DIP SWITCHES S2-1 , S2-2 OFF OFF** ON OFF* ON ON OFF ON** OFF OFF** ON OFF* ON ON OFF ON OFF OFF** ON OFF* ON ON OFF O
PAGE 47
*MES96& *CES96 Circulation Airflow MODEL GCES96/ ACES96/ VCES96 0403B GCES96/ ACES96/ VCES96 0603B GCES96/ ACES96/ VCES96 0804C GCES96/ ACES96/ VCES96 1005C GCES96/ ACES96/ VCES96 1205D GMES96/ AMES96/ 0403A VMES96 GMES96/ AMES96/ 0603B VMES96 GMES96/ AMES96/ 0803B VMES96 GMES96/ AMES96/ 0804C VMES96 GMES96/ AMES96/ 0805C VMES96 GMES96/ AMES96/ 1005C VMES96 GMES96/ AMES96/ 1205D VMES96 DIP SWITCHES S2-3 , S2-4 OFF OFF* ON OFF OFF ON ON ON OFF OFF* ON OFF OFF ON ON ON OFF OFF* ON OFF OFF ON ON ON
PAGE 48
*MES96& *CES96 Cooling Airflow DIP SWITCHES MODEL S1-1 , S1-2 , S13 OFF OFF OFF OFF ON ON ON OFF ON GCES96/ ON ON ON ACES96/ 0403B ON OFF OFF VCES96 ON ON OFF OFF ON OFF OFF OFF ON* OFF OFF OFF OFF ON ON ON OFF ON GCES96/ ON ON ON ACES96/ 0603B ON OFF OFF VCES96 ON ON OFF OFF ON OFF OFF OFF ON* OFF OFF OFF OFF ON ON ON OFF ON GCES96/ ON ON ON ACES96/ 0804C ON OFF OFF VCES96 ON ON OFF OFF ON OFF OFF OFF ON* OFF OFF OFF OFF ON ON ON OFF ON GCES96/ ON ON ON ACES96/ 1005C ON OFF OFF VCES96 ON ON OFF OFF ON OFF
PAGE 49
*MES96& *CES96 Cooling Airflow DIP SWITCHES MODEL S1-1 , S1-2 , S13 OFF OFF OFF OFF ON ON ON OFF ON GMES96/ ON ON ON AMES96/ 0603B ON OFF OFF VMES96 ON ON OFF OFF ON OFF OFF OFF ON* OFF OFF OFF OFF ON ON ON OFF ON GMES96/ ON ON ON AMES96/ 0803B ON OFF OFF VMES96 ON ON OFF OFF ON OFF OFF OFF ON* OFF OFF OFF OFF ON ON ON OFF ON GMES96/ ON ON ON AMES96/ 0804C ON OFF OFF VMES96 ON ON OFF OFF ON OFF OFF OFF ON* OFF OFF OFF OFF ON ON ON OFF ON GMES96/ ON ON ON AMES96/ 0805C ON OFF OFF VMES96 ON ON OFF OFF ON OFF
PAGE 50
HIGH VOLTAGE! Disconnect ALL power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury or death. Wiring Diagram *MES92*** (WITH PCBBF145 CONTROL) Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
PAGE 51
Special Instructions for Products Installed in the State of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall VENT/FLUE be sat
PAGE 52
CUSTOMER FEEDBACK We are very interested in all product comments. Please fill out the feedback form on one of the following links: Goodman® Brand Products: (http://www.goodmanmfg.com/about/contact-us). Amana® Brand Products: (http://www.amana-hac.com/about-us/contact-us). You can also scan the QR code on the right for the product brand you purchased to be directed to the feedback page. PRODUCT REGISTRATION Thank you for your recent purchase.