GPG16M Installation Instructions

2
REPLACEMENT PARTS
ORDERING PARTS
When reporting shortages or damages, or ordering repair parts,
give the complete unit model and serial numbers as stamped on
the unit’s nameplate.
TROUBLESHOOTING ............................................. 17
I
GNITION CONTROL ERROR CODES .............................17
F
AULT RECALL ............................................... 17
A
BNORMAL OPERATION - HEATING ............................ 17
INTERNAL CONTROL FAILURE ............................... 17
EXTERNAL LOCKOUT ...................................... 17
P
RESSURE SWITCH STUCK OPEN ........................... 17
PRESSURE SWITCH STUCK CLOSED ......................... 18
P
RIMARY LIMIT ............................................ 18
FLAME DETECTED WITH GAS VALVE CLOSED .............. 18
LOW FLAME SIGNAL ....................................... 18
A
BNORMAL OPERATION - COOLING ............................ 18
S
HORT CYCLE COMPRESSOR DELAY ........................18
H
IGH PRESSURE SWITCH/LOSS OF CHARGE SWITCH ......... 18
MAINTENANCE.................................................... 19
F
ILTER REPLACEMENT OR CLEANING ........................... 19
C
ABINET FINISH MAINTENANCE ................................ 19
C
LEAN OUTSIDE COIL (QUALIFIED SERVICER ONLY) ........... 19
C
ONDENSER, EVAPORATOR, AND INDUCED DRAFT MOTORS ......19
F
LAME SENSOR (QUALIFIED SERVICER ONLY) .................. 19
F
LUE PASSAGES (QUALIFIED SERVICER ONLY) ................. 19
CLEANING FLUE PASSAGES (QUALIFIED SERVICER ONLY) ....... 19
M
AIN BURNER FLAME (QUALIFIED SERVICER ONLY) ............ 19
C
LEANING BURNERS ........................................... 20
ACCESSORIES AND FUNCTIONAL PARTS ..................... 20
S
HEET METAL ACCESSORIES ................................... 20
F
UNCTIONAL PARTS .......................................... 20
G
ENERAL INFORMATION ....................................... 20
APPENDIX .......................................................... 21
I
GNITION CONTROL DIAGNOSTIC INDICATOR CHART .............21
H
EATING TIMING CHART ...................................... 21
C
OOLING TIMING CHART ......................................21
U
NIT DIMENSIONS ............................................. 22
W
IRING DIAGRAM ............................................. 23
MINIMUM CLEARANCES ........................................24
R
ECOMMENDED FILTER SIZES .................................. 24
B
LOWER PERFORMANCE ....................................... 25
S
TART-UP CHECKLIST ................................... 27-28
REPLACEMENT PARTS............................................ 2
ORDERING PARTS .............................................. 2
SAFETY INSTRUCTIONS .......................................... 3
UNIT LOCATION ................................................... 4
A
LL INSTALLATIONS: ........................................... 4
G
ROUND LEVEL INSTALLATIONS ONLY: .......................... 4
R
OOFTOP INSTALLATIONS ONLY: ................................ 5
R
OOF CURB INSTALLATIONS ONLY: ............................. 5
GENERAL INFORMATION ......................................... 5
T
RANSPORTATION DAMAGE ..................................... 5
RIGGING DETAILS .................................................. 6
GAS PIPING ......................................................... 6
H
IGH ALTITUDE DERATE (U.S. INSTALLATIONS ONLY) ......... 6
P
IPING ........................................................ 6
G
AS PIPING CHECKS ........................................... 7
PROPANE GAS INSTALLATIONS ................................. 7
T
ANKS AND PIPING ............................................. 8
ELECTRICAL WIRING.............................................. 8
THERMOSTAT LOCATION ....................................... 8
S
INGLE STAGE THERMOSTAT .................................... 9
U
NIT VOLTAGE ............................................... 10
H
EAT ANTICIPATOR SETTING ................................... 10
CIRCULATING AIR AND FILTERS ............................... 11
A
IRFLOW CONVERSION ........................................ 11
D
UCTWORK .................................................. 11
FILTERS ...................................................... 11
VENTING ........................................................... 11
I
NSTALLATION - FLUE HOOD EXHAUST ........................ 11
I
NSTALLATION - COMBUSTION AIR INTAKE HOOD ............... 12
CONDENSATE DRAIN............................................. 12
C
ONDENSATE DRAIN CONNECTION ............................. 12
NORMAL SEQUENCES OF OPERATION ........................ 12
H
EATING ..................................................... 12
COOLING ..................................................... 12
F
AN ONLY ................................................... 13
STARTUP, ADJUSTMENTS, AND CHECKS ..................... 13
H
EATING STARTUP ............................................13
C
OOLING STARTUP ............................................ 16
INDEX
Replacement parts for this appliance are available through your
contractor or local distributor. For the location of your nearest
distributor, consult the white business pages, the yellow page
section of the local telephone book or contact:
HOMEOWNER SUPPORT
GOODMAN MANUFACTURING COMPANY, L.P.
19001 KERMIER ROAD
WALLER, TEXAS 77484
[phone]