Installation Manual

ManualsBrandsGoodman ManualsCentral Air & Heating3 Ton 15 SEER Heat Pump Variable Speed Air Conditioner System - Horizontal

TTENTION

NSTALLING

ERSONNEL

As a professional installer, you have an obligation to know the product better than the customer. This includes all safety

precautions and related items.

Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual. Pay special attention to all safety

warnings. Often during installation or repair, it is possible to place yourself in a position which is more hazardous than

when the unit is in operation.

Remember, it is your responsibility to install the product safely and to know it well enough to be able to instruct a

customer in its safe use.

Safety is a matter of common sense...a matter of thinking before acting. Most dealers have a list of specific good safety

practices...follow them.

The precautions listed in this Installation Manual are intended as supplemental to existing practices. However, if there is

a direct conflict between existing practices and the content of this manual, the precautions listed here take precedence.

AFETY

RECAUTIONS

The following symbols and labels are used throughout this manual to indicate immediate or potential safety hazards. It

is the owner’s and installer’s responsibility to read and comply with all safety information and instructions accompanying

these symbols. Failure to heed safety information increases the risk of personal injury, property damage, and/or product

damage.

HKR / HKA / HKP

ELECTRIC HEAT KIT

INSTALLATION INSTRUCTIONS

IO-365D

11/2014

HIGH VOLTAGE !

ISCONNECT

ALL

POWER

BEFORE

SERVICING

ULTIPLE

POWER

SOURCES

MAY

PRESENT

. F

AILURE

MAY

CAUSE

PROPERTY

DAMAGE

PERSONAL

INJURY

DEATH

WARNING

ONLY

INDIVIDUALS

MEETING

THE

REQUIREMENTS

“E

NTRY

EVEL

ECHNICIAN

”

SPECIFIED

THE

ONDITIONING

, H

EATING

AND

EFRIGERATION

NSTITUTE

(AHRI)

MAY

USE

THIS

INFORMATION

TTEMPTING

INSTALL

REPAIR

THIS

UNIT

WITHOUT

SUCH

BACKGROUND

MAY

RESULT

PRODUCT

DAMAGE

PERSONAL

INJURY

DEATH

WARNING

HIS

APPLIANCE

MUST

INSTALLED

FOLLOWING

THE

ANSI/NFPA

70 (N

ATIONAL

LECTRIC

ODE

)

AND

OTHER

APPLICABLE

CODES

WARNING

AILURE

THESE

INSTRUCTIONS

CAN

CAUSE

FIRE

EXPLOSION

ELECTRICAL

SHOCK

PROPERTY

DAMAGE

PERSONAL

INJURY

DEATH

WARNING

AVOID

POSSIBLE

PERSONAL

INJURY

USE

EXTREME

CAUTION

USING

POWER

TOOLS

REMOVE

THE

SMALL

BREAKER

MOUNTING

BRACKETS

. T

BRACKETS

MAY

QUICKLY

ROTATE

AND

CAUSE

INJURY

DEATH

CAUTION

Summary of content (8 pages)

PAGE 1
HKR / HKA / HKP ELECTRIC HEAT KIT INSTALLATION INSTRUCTIONS ATTENTION INSTALLING PERSONNEL As a professional installer, you have an obligation to know the product better than the customer. This includes all safety precautions and related items. Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual. Pay special attention to all safety warnings.
PAGE 2
RISQUE D'EMPOISONNEMENT AU MONOXYDE DE CARBONE Advertencia especial para la instalación de calentadores ó manejadoras de aire en áreas cerradas como estacionamientos ó cuartos de servicio. Las emisiones de monóxido de carbono pueden circular a través del aparato cuando se opera en cualquier modo. CO can cause serious illness including permanent brain damage or death.
PAGE 3
Steps 4 through 7 and 10 pertain to kits that contain circuit breakers. 4. Remove the circuit breaker mounting bracket, leaving the circuit breakers connected. 5. AR, ARUF, ARPF, AEPF, ASPF, AVPTC, MBVC, MBE and MBR models. Mount the circuit breaker mounting bracket as shown using the supplied screws. Insert two of the screws through the blower deck from the blower side. Insert the remaining screws in the holes provided on the upper right side of the jacket.
PAGE 4
“H” SERIES PACKAGE UNIT INSTALLATION NOTE: A separate power supply is required for the HKR/HKP heater kits. WARNING 1. Disconnect all power to the unit, both indoor and outdoor. HIGH VOLTAGE ! 2. Remove the control box cover and blower panel. STRAIN RELIEF AND CONDUCTOR PROTECTION MUST BE 3. Remove cover to the electric heat kit box. 4. Break out appropriate knockout for electric heat kit based on kW of element (# of elements). 5. Remove heater kit from packaging. 6.
PAGE 5
8. Attach contactors to included “H” model vertical contactor plate (Figure 4). Ensure contactor lugs are pointed inward towards each other. 9. Slide the heater kit into the slot following the direction of airflow decal for package unit operation attached to the heater faceplate and secure with screws provided. FIGURE 4 10. Install two of the four mounting screw on heaterkit (Figure 5). 11. Place vertical contactor bracket behind corner post. 12.
PAGE 6
NOTE: To replace the electric heat kit cover, slightly tip the cover and insert only the notches under the flanges on the top and bottom of the box. Secure with screws. See Figure 7. ATTACH CIRCUIT BREAKER MOUNTING BRACKET WITH PROVIDED SHEET METAL SCREW FLANGE CIRCUIT BREAKER KNOCKOUTS 18. Ensure breaker is in the ON position. Replace blower panel cover and check operation through the room thermostat. TIP IN SLIGHTLY AND SECURE NOTCHES BEHIND FLANGE 19. RESTORE POWER. 20.
PAGE 7
. Install heater element(s) with the four (4) pointed screws included in the unit literature bag. Note the air flow direction label located on the heater element base shown in Figure 10. Orient the heating element base to match airflow direction on package unit blower assembly. Ensure scews attaching horseshoe contactor plate fit into relief cuts of package unit. 8.
PAGE 8
NOTE: On earlier (M) models it may be necessary to notch or cut heater kit shroud to accomodate screws in heater (Figure 14). FIGURE 14 NOTE: To accomodate 6-gauge wires, it may be necessary to make cuts as shown on the heater kit cover. Ensure grommet edging is used along sharp edges to prevent injury (Figure 15). FIGURE 15 NOTE: If necessary to connect line power to unit, drill a 1” hole at the coordinates provided in Figure 16.