SPK Installation Instructions

ManualsBrandsGoodman ManualsAccessoriesSingle Point 40 Wiring Kit

Attention Installing Personnel

As a professional installer, you have an obligation to know the

product better than the customer. This includes all safety precau-

tions and related items.

Prior to actual installation, thoroughly familiarize yourself with this

Instruction Manual. Pay special attention to all safety warnings.

Often during installation or repair, it is possible to place yourself in

a position which is more hazardous than when the unit is in opera-

tion.

Remember, it is your responsibility to install the product safely

and to know it well enough to be able to instruct a customer in its

safe use.

Safety is a matter of common sense...a matter of thinking before

acting. Most dealers have a list of specific good safety

practices...follow them.

The precautions listed in this Installation Manual are intended as

supplemental to existing practices. However, if there is a direct

conflict between existing practices and the content of this manual,

the precautions listed here take precedence.

Description

The following installation instructions supplement is for the SPK

Single Point Wiring kits for installation in the following models:

*P**CH**41

*P**HH**41

*PC****H41

*PH****H41

*P**CM**41

*P**HM**41

*PC****M41

*PH****M41

Horizontal

Models

Multi-Position

Models

These instructions should be used only as a supplement to the

installation instructions provided with the above units.

SPK SINGLE POINT WIRING KITS

INSTALLATION INSTRUCTIONS

WARNING

HIGH VOLTAGE!

DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING

THIS UNIT.

MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE

TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR

DEATH.

CAUTION

TO AVOID POSSIBLE PERSONAL INJURY, USE EXTREME CAUTION IF USING

POWER TOOLS TO REMOVE THE SMALL BREAKER MOUNTING BRACKETS.

BRACKETS MAY QUICKLY ROTATE AND CAUSE INJURY.

Remove the contents of the SPK from the box and check inventory

with Table 1 before starting.

Part Qty.

Single Point Assembly 1

- Mounting Plate 1

- Cover 1

- Distribution Block 1

- Breaker 1

- Black Electric Heat Wires 5

- Unit Wire Harness 1

- Wire from Block to Breaker 2

Literature Bag 1

- Installation Instructions 1

- Wiring Diagram 1

- 1/4" Male Multiplier Terminals 2

- Cutting Screw 1

- Blunt Tip Screw 1

- Wire Ties 4

Table 1

IO-797A

9/2013

Summary of content (4 pages)

PAGE 1
SPK SINGLE POINT WIRING KITS INSTALLATION INSTRUCTIONS WARNING Attention Installing Personnel As a professional installer, you have an obligation to know the product better than the customer. This includes all safety precautions and related items. Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual. Pay special attention to all safety warnings.
PAGE 2
Horizontal Models 1. Bring unit harness to control box through grommet here. Disconnect all power to the unit. WARNING Cut appropriately sized hole in this area. HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. M ULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE - OR - TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR Use knock-out on the bottom left side of the unit. DEATH. 2. Remove control box door and blower door (Figure 1). Figure 3 6. 7. Control Box Door 8. 9.
PAGE 3
16. Place the cover on the kit as shown in Figure 4. Drive the cutting screw provided with the single point kit to attach the cover using the hole shown in Figure 4. Once the hole is made, remove the cutting screw and replace with the blunt tip screw also provided with the kit. NOTE: Breaker for single point kit must be in the OFF position, for the cover to fit correctly. Use Cutting Screw to attach kit cover. Single Point Breaker Figure 6 5. Figure 4 17. Flip single point breaker to the ON position.
PAGE 4
12. Route the remaining 4 black and one green electric heat wires to the electric heat compartment. 13. Connect the green wire to the ground lug on the electric heat kit. 14. For heat pumps, connect the 2 wires coming from the middle lug on the distribution block to the L1 lugs on the breakers of the electric heat kit (1 wire per breaker/smaller gauge wire on smaller amperage breaker).