Safety Information

ManualsBrandsGoogle ManualsComputers & AccessoriesWireless device

Jacquard Safety & Regulatory Guide

(Tag)

Using the Jacquard tag

1. Install the APP by visiting the Google Play Store or iTunes Store.

2. Open the APP by tapping the APP icon on your Android/IOS device.

3. Tap “Get Started”.

4. Tap “Enable device”.

5. To pair your device, select the corresponding serial number that matches the label on

the device. Once the device is found, pairing will start automatically.

Safety & Regulatory Guide for Jacquard tag

This booklet provides important safety and regulatory information that you should read before

using your Jacquard tag.

Basic safety

WARNING: HEALTH AND SAFETY INFORMATION

To avoid damaging your device, accessories or any connected devices, and to reduce the risk of

personal injury, discomfort, property damage or other potential hazards, follow the precautions

below:

● Handle your Jacquard tag with care. You may damage Jacquard tag or the battery if you

puncture, burn, deform, crush, drop, modify, attempt to insert foreign objects into or

disassemble them. Do not bend the Jacquard tag unnecessarily. Using a damaged

Jacquard tag may cause battery overheating or injury. Don’t expose your Jacquard tag

to liquids, which can cause a short circuit and overheating. If the tag gets wet, do not

attempt to dry it using an external heat source. The tag is designed to operate in a dry,

indoor environment.

● Jacquard is designed to work best in ambient temperatures between 32° to 95°F (0° to

35°C), and should be stored between ambient temperatures of -4° and 113°F (-20° and

45°C). Do not expose the Jacquard tag to temperatures above 113°F (40°C), such as on

a car dashboard or near a heating vent as this may damage the product, overheat the

battery, or pose a risk of fire. Keep your Jacquard tag away from heat sources and avoid

prolonged exposure to direct sunlight. If the Jacquard tag becomes too hot, disconnect

it from its power source if it is plugged in, move it to a cooler place and don’t use it until

it has cooled.

Summary of content (5 pages)

PAGE 1
Jacquard Safety & Regulatory Guide (Tag) Using the Jacquard tag 1. 2. 3. 4. 5. Install the APP by visiting the Google Play Store or iTunes Store. Open the APP by tapping the APP icon on your Android/IOS device. Tap “Get Started”. Tap “Enable device”. To pair your device, select the corresponding serial number that matches the label on the device. Once the device is found, pairing will start automatically.
PAGE 2
Repair & Service Don’t attempt to repair the Jacquard tag yourself. Disassembling the Jacquard tag may result in loss of water resistance. Disassembling Jacquard may cause injury. Battery The Jacquard tag contains a lithium-ion battery, which is a sensitive component that can cause injury if damaged. Do not attempt to remove the battery. Replacement by non-qualified professionals can damage your device.
PAGE 3
resulting in bodily injury or even death. Observe all notices and signs where these hazards might be present. Proper Handling and Usage Operating Temperatures If the interior temperature of the Jacquard tag exceeds or falls below normal operating temperatures, you may experience the following behaviors while the device tries to regulate its temperature: reduced battery performance and connectivity, inability to charge, lack of LED and vibration notification or device power down.
PAGE 4
Important: This product has demonstrated EMC compliance under conditions that included the use of compliant peripheral devices and shielded cables between system components. It is important that you use compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, televisions, and other electronic devices.
PAGE 5
Innovation, Science and Economic Development (ISED) Canada Regulatory Compliance Innovation, Science and Economic Development Canada (ISED Canada)/Innovation, Sciences et Développement économique Canada Industry Canada/Industrie This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.