INSTRUCTION MANUAL 使用说明书 #1 BY DESIGN 2022 Thank you for choosing Goosky Technology series products. Before entering the remote control world, you must be told a lot of relevant knowledge and precautions to ensure that you can be more comfortable in the learning process. Before starting the operation, please read this manual carefully. We believe it will be of great help to you. Please keep this manual properly for future reference.
INTRODUCTION 前言 Thank you for purchasing Goosky products. In order to use the S2 helicopter easily and conveniently, please read this manual in detail before assembling and operating this helicopter. At the same time, please keep this manual properly for future adjustment and maintenance reference. S2 is a new product developed by Goosky. No matter you are a beginner who needs stable flight or a flight enthusiast who pursues excellent performance, S2 is your best choice.
Precautions before use 使用前须知 FORBIDDEN 禁止 LOCATE AN APPROPRIATE LOCATION 远离障碍物及人群 Helicopter flying has a certain speed, which is relatively potentially dangerous. The choice of venue is also relatively important. Please abide by local laws and regulations and go to a legal remote control flight venue to fly. You must pay attention to whether there are people, high-rises, buildings, high-voltage wires, trees, etc.
EQUIPMENT REQUIRED FOR ASSEMBLY 自备工具 Knife 刀子 Philips Screw Drive 十字螺丝起子 Scissors 剪刀 Diagonal Cutting Pliers 斜口钳 Needle Nose Pliers 尖嘴钳 Hexagon Screw Driver 六角螺丝起子 CA瞬间胶 lubricating oil AB Glue AB胶 胶水使用方法 Instructions of using glue For the assembly steps marked with the following symbols, please use glue or oil to ensure the reliability of use.
Specifications 参数规格 144 440 71.
step 1 步骤一 ! CAUTION Thrust braring and washer for radial bearing are wear items,and thus should be inspected for replacement after every 20 flights. For flights with high headspeed ,the inspection interval should be reduced to ensure flight safety. Concave opening of bearing face inside ase Gre Flat bearing gasket (Ø3*Ø4.5*0.1mm) Ball Bearing-MR63ZZ (Ø3*Ø6*2.5mm)x4 main propeller clip Thrust bearings Ø3*Ø6*2.8mm) Main collet bearing bushing Φ3.1*Φ4.4*1.4mm)x2 Ball Bearing-MR63ZZ (Ø3*Ø6*2.
step 2 步骤二 Socket screw Ball Bearing-681X (Φ1.5*Φ4*2mm) Socket screw Copper sets Copper sets (Φ1.5*Φ2.8*0.4mm) Copper sets Ball Bearing-681X (Φ1.5*Φ4*2mm)x8 Inner ball head seat Copper sets Ball Bearing-681X (Φ1.5*Φ4*2mm) Copper sets FBL control arm Socket screw Copper sets (Φ1.5*Φ2.8*0.4mm)x2 Copper sets Copper sets Socket screw Socket screw Copper sets Ball head screw (Φ3.175*5.7mm-M1.6) Ball head screw (Φ3.175*6.3mm-M1.6) Ball head screw (Φ3.175*15mm-M1.6) Ball head screw (Φ3.175*5.
step 3 步骤三 Ball Bearing-MR104ZZ ( Φ4*Φ10*4 ) Socket screw (M1.6X6) Socket screw Bearing limit carbon plate (M2X6) Socket screw (M2X6) Servo bracket Ball Bearing-MR104ZZ ( Φ4*Φ10*4 ) second floor ! CAUTION Motherboard Ball Bearing-MR104ZZ ( Φ4*Φ10*4 )x2 Socket screw Socket screw (M1.6x6mm)x2 (M2x6mm)x3 M1.6 Nut M1.6 Servo Arm Linkage Ball (Φ3.175*7.3) CCPM舵机 CCPM servo Socket screw M1.6x4mm Socket screw M1.6x4mm ! Socket screw CAUTION M1.
step 4 步骤四 Socket screw M1.6x4mm Frame Widening Mount Socket screw M1.6x4mm Socket screw Socket screw M1.6x3mm M1.6x4mm Frame Widening Mount Socket screw M2x4mm Socket screw Socket screw (M1.6x4mm)x6 (M1.6x3mm)x4 Chassis fixing column Tail Boom Mount Socket screw (M2x4mm)x2 Socket screw (M2.5x6mm) CAUTION ! Main Shaft Motor shaft fixing sleeve Machine screw M3*4mm Socket screw (M2.
step 5 步骤五 cross recessed countersunk head tapping screws (ST1.6x4mm) Body reinforcement cross recessed round head tapping screw (ST1.5X6 ) card buckle right panel cross recessed round head tapping screw Socket screw (M1.6x3mm) cross recessed round head tapping screw left panel motor cable cover (ST1.5X4 ) Socket screw (ST1.5X6)x6 (M1.6x3mm) cross recessed countersunk head tapping screws (ST1.6x4mm)x2 cross recessed round head tapping screw (ST1.5x4mm) Socket screw (M1.
step 6 步骤六 ! CAUTION 步骤 In this step, the M1.6*4 screws fixing the motor components on both sides should not be completely locked in place. Socket screw 六 (M1.6x4mm) ! CAUTION Socket screw 六 (M1.6x4mm) Socket screw 六 (M1.6x4mm)x4 ! CAUTION Socket screw 六 (M1.6x5mm) After assembling the main frame components, fully lock the 4 M1.6*4 screws on both sides of the side panel. Socket screw 六 (M1.6x5mm) Socket screw 六 (M1.6x4mm) Socket screw 六 (M1.6x4mm) Socket screw 六 (M1.6x5mm)x2 EN 11 WWW.
step 7 步骤七 Socket screw Tailpipe (M1.6x4mm) Tailpipe inner mount 尾管内部固定座 Socket screw (M1.6x5mm) Socket screw Tail motor reinforced plate group 尾侧板加强片 (M1.6x4mm)x2 Tail Fin Socket screw (M1.6x5mm)x2 tail rotor Socket screw (M1.6x4mm) M1.6 screw sleeve M1.6 tail motor 尾电机 Socket screw Socket screw (M1.6x4mm)x4 (M1.6x4mm) M1.6 screw sleeve M1.6 EN 12 WWW.GOO-SKY.
step 8 步骤八 Socket screw Socket screw Socket screw M2x12mm-L4 (M2x12mm-L4)x2 Socket screw M2 Nut M2 Socket screw Socket screw M2 Nut M2 EN 13 WWW.GOO-SKY.
step 9 步骤九 Plastic ball link Plastic ball link Plastic ball link Plastic ball link EN 14 WWW.GOO-SKY.
step 10 步骤十 Plastic ball link Plastic ball link Socket screw (ST1.7X6 ) Croduct Phase Panel Set Socket screw (ST1.7X6 ) Socket screw Plastic ball link (ST1.7X6 ) EN 15 WWW.GOO-SKY.
step 11 步骤十一 Flight control 3M shock absorber ! CAUTION Note: 1: First, fully fit the double-sided shock-absorbing sticker to the upper seat of the battery compartment, and then install the flight controller. 2: The edge of the outgoing end of the flight control module is aligned with the edge of the square groove, which is on the upper seat of the bottom battery compartment (as shown in the blue line). And the left and right are centered.
step 12 步骤十二 cross recessed round head tapping screw 十 Canopy spring Canopy button Canopy lower shell cross recessed round head tapping screw 十 cross recessed mechanical Jaw round head screw 圆头十字机械牙螺丝(M1.4X4)x2 Canopy upper shell hook 头罩上壳卡钩 Canopy upper shell 头罩上壳 cross recessed mechanical Jaw round head screw 圆头十字机械牙螺丝 (M1.4X4)x2 EN 17 WWW.GOO-SKY.
step 13 步骤十三 Phillips screws 十 (ST1.5X4 ) Socket screw cross recessed round head tapping screw 十 (ST1.5X4 ) Socket screw cross recessed round head tapping screw 十 (ST1.5x4mm) Socket screw (M1.6x4mm)x2 EN 18 WWW.GOO-SKY.
step 14 步骤十四 M2 Nut M2 Socket screw Socket screw (M2x6mm) (M2x6mm) M2 Nut M2 Socket screw (M2x6mm)x2 EN 19 WWW.GOO-SKY.
step 15 步骤十五 Main propeller Socket screw Flat bearing gasket ( mm) Socket screw M2 screw sleeve M2 screw sleeve Flat bearing gasket ( mm) Flat bearing gasket M2 Nut Main propeller M2 Flat bearing gasket Socket screw ! CAUTION M2 screw sleeve Notice: 1: Each group of main propellers has been selected, weighed and matched before leaving the factory. When there are multiple pairs of main propellers at the same time, multiple groups cannot be mixed and used.
step 16 步骤十六 Press the button to open the lower case ! CAUTION Notice: 1: Press the lower case button to open the lower case; ! CAUTION Notice: 1: Install the battery to the end; 2: Press and hold the lower case button, and close the case upwards to ensure that the case lock is in place; EN 21 WWW.GOO-SKY.
step 17 步骤十七 ! CAUTION How to disassemble the upper case: 1: Disassemble the fixing screws on both sides. 2: The propeller is turned to the side of the fuselage, and the two blades are retracted. 3: Move the upper casing upwards and turn it 90 degrees toward the blade position, and it can be disassembled; EN 22 WWW.GOO-SKY.
step 18 步骤十八 EN 23 WWW.GOO-SKY.
step 19 步骤十九 Data 5V 3.3V Data 5V Data CH3 CH2 CH1 TX RX Flight Parameter Setting lntroduction 飞行参数设置说明 General Flight Mode 一般飞行模式 Throttle 油门 EN IDLE 2 Mode IDLE 2模式 IDLE 1 Mode IDLE 1模式 Screw Pitch 螺距 Throttle 油门 Screw Pitch 螺距 Throttle 油门 Screw Pitch 螺距 5 60 100 11.5° 5 65 100 11.5° 5 73 100 11.5° 4 60 65 5.5° 4 65 50 5.5° 4 73 50 5.5° 3 60 15 1.8° 3 65 5 0.6° 3 73 0 0° 2 60 -5 -0.6° 2 65 -50 -5.5° 2 73 -50 -5.5° 1 0 -20 -2.
Spare parts picture-1 配件-1 Package: Hang tag +PE bag Model: SPH000001 包装方式：吊卡+PE袋 配件编号: SPH000001 Product name: Main rotorhousing set 配件名称: 主轴中心座组 适用机型: RS2 S2 Package: Hang tag +PE bag Model: SPH000002 包装方式：吊卡+PE袋 配件编号: SPH000002 Product name: Damper Rubber 配件名称: 横轴避震套组 适用机型: RS2 S2 单品8PCS Package: Hang tag +PE bag Model: SPH000003 包装方式：吊卡+PE袋 配件编号: SPH000003 Product name: Rotor Holder Set 配件名称: 主桨夹组 压好轴承 Package: Hang tag +PE bag Model: SPH000004 包装方式：吊卡+PE袋 配件编号: SPH000004 Product name:Feathering
Spare parts picture-1 配件-1 Model: SPH000021 配件编号: SPH000021 Product name: Left Panel Set 配件名称: 左侧板组 Package: Hang tag +PE bag 包装方式：吊卡+PE袋 Package: Hang tag +PE bag Model: SPH000022 包装方式：吊卡+PE袋 配件编号: SPH000022 Product name: Right side plate set 配件名称: 右侧板组 适用机型: RS2 S2 装配线卡、过线套 Package: Hang tag +PE bag Model: SPH000023 包装方式：吊卡+PE袋 配件编号: SPH000023 Product name: Upper side panel 配件名称: 上侧板 适用机型: RS2 S2 适用机型: RS2 S2 单品 2PCS Package: Hang tag +PE bag Model: SPH000024 包装方式：吊卡+PE袋 配件编号: SPH000024 Product n
Spare parts picture-1 配件-1 Package: Hang tag +PE bag Model: SPH000041 包装方式：吊卡+PE袋 配件编号: SPH000041 Product name: vertical wing-Green 配件名称: 垂直翼-绿 Package: Hang tag +PE bag Model: SPH000042 包装方式：吊卡+PE袋 配件编号: SPH000042 Product name: vertical wing-blue 配件名称: 垂直翼-蓝 适用机型: S2 Model: SPH000043 配件编号: SPH000043 Product name: Main Blades 配件名称: 主桨组 Package: Hang tag +PE bag 包装方式：吊卡+PE袋 适用机型: S2 Package: Hang tag +PE bag Model: SPH000044 包装方式：吊卡+PE袋 配件编号: SPH000044 Product name: Main rotor holder set 配件名称: 主桨固定配件组
Spare parts picture-1 配件-1 Package: Hang tag +PE bag Model: SPH000059 包装方式：吊卡+PE袋 配件编号: SPH000059 Product name: Canopy Accessories set 配件名称: 机壳配件组 Package: Hang tag +PE bag Model: SPH000060 包装方式：吊卡+PE袋 配件编号: SPH000060 Product name: Canopy Set--yellow red 配件名称: 机头罩--黄红色 适用机型: RS2 S2 Package: Hang tag +PE bag Model: SPH000061 包装方式：吊卡+PE袋 配件编号: SPH000061 Product name: Canopy Set--yellow green 配件名称: 机头罩--黄绿色 适用机型: S2 适用机型: S2 Package: Hang tag +PE bag Model: SPH000062 包装方式：吊卡+PE袋 配件编号: SPH000062 Product n
Transmitter description-1 遥控器说明-1 Remote Control Power Light(Red) 遥控器 (MODEL 2) HOLD IDLE Pose mode Manual mode Manual mode D/R Throttle, Orientation 70% 85% 100% Front Back, Left Right Flying Ring POWER-2 POWER-1 Remote Control Power Light(Red) 遥控器 (MODEL 1) HOLD IDLE D/R Front Back, Left Right Throttle, Orientation Flying Ring POWER-2 POWER-1 EN 70% 85% 100% Pose mode Manual mode Manual mode WWW.GOO-SKY.
遥控 Handle 提手 (Product Model)产品型号：T8 (Diameters)外形尺寸长：L153*W93*H154 (Radio Frequency)无线频率：2.404GHz--2.4475 GHz (Transmit Power)发射功率：< 20 dBm (Weight)重量约：335g (Modulation Mode)调制方式：2FSK (Spread Spectrum Mode)扩频方式：FHSS (Working Voltage)工作电压：3.7V (Remote Distance)遥控距离：300m (Charge Interface)充电接口：TYPE-C (Low Voltage Alarm)低电压报警：3.35V (Battery Type)电池类型：Lithium Polyer Battery (Battery Capacity)电池容规格：2800mAh 3.
Memo 备忘录 EN WWW.GOO-SKY.
Zhongshan Goosky Technology Innovation Co., Ltd. www.goo-sky.
