EN DETAILED INSTRUCTIONS OF THE ELECTRIC PYROLYTIC OVEN www.gorenje.
We thank you for your trust and the purchase of our appliance. This detailed instruction manual is supplied to make the use of this product easier. The instructions should allow you to learn about your new appliance as quickly as possible. Make sure you have received an undamaged appliance. If you do find transport damage, please contact the seller from which you purchased the appliance, or the regional warehouse from which it was supplied.
CONTENTS INTRODUCTION 4 THE ELECTRIC PYROLYTIC OVEN 8 Control unit 10 Technical specifications 11 IMPORTANT SAFETY INSTRUCTIONS 13 Before connecting the oven: 14 BEFORE USING THE APPLIANCE FOR THE FIRST TIME PREPARING THE APPLIANCE FOR THE FIRST USE COOKING STEPS 15 STEPS OF THE COOKING PROCESS (1–6) 15 16 18 21 23 23 Step Step Step Step Step Step 1: SWITCHING ON AND SETTINGS 2: CHOOSING THE COOKING SYSTEM 3: CHOOSING THE SETTINGS 4: SSELECTING ADDITIONAL FUNCTIONS 5: STARTING THE COOKING PROCESS
THE ELECTRIC PYROLYTIC OVEN (DESCRIPTION OF THE OVEN AND EQUIPMENT – DEPENDING ON THE MODEL) The figure represents one of the built-in appliance models. Since the appliances for which these instructions were drawn up may have different equipment, some functions or equipment may be described in the manual that may not be present in your appliances. Control unit Door switch 4 3 Guides - Cooking levels 2 1 Oven door Oven handle PUSH-PULL KNOB Slightly push the knob until it pops out; then, rotate it.
WIRE GUIDES Chrome-plated (silver) and enamel-coated PYROLITIC (black) wire guides. Before pyrolitic cleaning, the chrome-plated (silver) wire guides should be removed from the oven! The wire guides allow preparation of the food on four levels (please note that the levels/ guides are counted from the bottom up). Guides 3 and 4 are intended for grilling. TELESCOPIC PULL-OUT GUIDES Telescopic pull-out guides may be fitted for the 2nd, 3rd, and 4th level. Pull-out guides can be partly or fully extendible.
The GRID is used for grilling or as support for a pan, baking tray or baking dish with the food. There is a safety latch on the grid. Therefore, lift the grid slightly at the front when pulling it out from the oven. The SHALLOW BAKING SHEET is used for baking pastry and cakes. The DEEP BAKING TRAY is used for roasting meat and baking moist pastry. It can also be used as a drip tray.
4 3 With telescopic extendible guides, first pull out the guides of one level and place the grid or the baking tray onto them. Then, push them in with your hand as far as they will go. 2 Close the oven door when the telescopic guides are retracted all the way into the oven. CATALYTIC INSERTS prevent the spraying fat from sticking to sides of the oven cavity. The ROTISSERIE (meat skewer) is used for roasting meat. The set consists of a skewer support, skewer with screws, and a removable handle.
CONTROL UNIT (DEPENDING ON THE MODEL) 16 1 COOKING SYSTEM SELECTOR KNOB 2 CHILD LOCK KEY 3 OVEN LIGHTING ON/ OFF KEY 4 TEMPERATURE KEY NOTE: Symbols of cooking systems may be located on the knob or on the front panel (depending on the appliance model).
16 5 ELECTRONIC TIMER KEY Cooking duration End of cooking 6 START/STOP KEY Use this key to start or stop the program. 7 SETTINGS KNOB (-/+) 8 COOKING INFORMATION AND CLOCK DISPLAY Use this knob to set the time and temperature. Alarm Clock 503555 NOTE: The keys will respond better if you touch them with a larger area of your fingertip. Each time you press a key, a short acoustic signal will be sounded.
TECHNICAL SPECIFICATIONS xxxxxx TYPE: XXXXXX ART. Nr: SER. Nr: XXXXXX The rating plate indicating the basic information about the appliance is located at the edge of the oven and it is visible when the oven door is opened. 503555 10 220-240V ~ 220V-240V, 50/60Hz Pnmax : 3.
IMPORTANT SAFETY INSTRUCTIONS CAREFULLY READ THE INSTRUCTIONS AND SAVE THEM FOR FUTURE REFERENCE. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. During use the appliance becomes hot.
The appliance is intended for household use. Do not use it for any other purpose, such as room heating, drying of pets or other animals, paper, fabrics, herbs etc. as this may lead to injury or fire hazard. Do not line the oven walls with aluminium foil and do not place baking trays or other cookware on the oven bottom. Aluminium foil would prevent air circulation in the oven, hinder the cooking process, and ruin the enamel coating.
Safe use of the oven during pyrolytic cleaning Before activating the automatic cleaning process, remove the grid, the spit roasting kit, glass baking trays, meat probe, and any other cookware that is not a part of oven equipment. During the automatic pyrolytic cleaning process, the oven gets very hot on the outside. Risk of burns! Keep children away from the oven.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME Upon receiving the appliance, remove all parts, including any transport equipment, from the oven. Clean all accessories and utensils with warm water and regular detergent. Do not use any abrasive cleaners. When the oven heats up for the first time, the characteristic smell of a new appliance will be emitted. Ventilate the room thoroughly during the first use.
STEPS OF THE COOKING PROCESS (1–6) STEP 1: SWITCHING ON AND SETTINGS After connecting your appliance or after an extended power outage, 12:00 will flash on the display and the symbol will light up . Set the time of day. SETTING THE CLOCK 1 Rotate the SETTINGS KNOB (-/+) and first set the minutes; then, the cursor will switch to hours. After three seconds, the settings will be saved. Turning the knob farther to the right or to the left will change the settings more quickly.
STEP 2: CHOOSING THE COOKING SYSTEM Rotate the knob (left and right) to select 0 COOKING SYSTEM (see program table). The selected icon will appear on the display. Settings can also be changed during the cooking process. SYSTEM DESCRIPTION SUGGESTED TEMPERATURE °C COOKING SYSTEMS 503555 16 RAPID PREHEAT Use this function if you wish to heat the oven to the desired temperature as quickly as possible. This function is not appropriate for cooking food.
DESCRIPTION SUGGESTED TEMPERATURE °C BOTTOM HEATER AND FAN This is used for baking leavened but low-rising pastry and for preserving fruit and vegetables. 180 PLATE WARMER Use this function to reheat your dinnerware (plates, cups) before serving food in it to keep the food warm longer. 60 DEFROSTING The air circulates with no heaters activated. Only the fan will be activated. This is used to slowly thaw frozen food. Automatic programs also allow defrosting with microwaves (A1 to A5).
STEP 3: CHOOSING THE SETTINGS Each cooking system features basic or default settings which can be adjusted. Adjust the settings by pressing the relevant key (before pressing the START/STOP key). Some settings are not available with some programs; an acoustic signal will remind you of such cases. CHANGING THE COOKING TEMPERATURE 1 Select the COOKING SYSTEM. Selected icon will appear on the display and PRESET TEMPERATURE will flash. 2 Select the COOKING SYSTEM.
TIMER FUNCTIONS First rotate the COOKING SYSTEM SELECTOR KNOB; then, set the temperature. Touch the TIMER key several times to select the desired timer function. The icon for the selected timer function will light up and the adjustable cooking start/end time will flash on the display. Other icons are dimly lit. Press START to start the cooking process. ELAPSED COOKING TIME will be displayed.
Setting the minute minder The minute minder can be used independently of the oven operation. The longest possible setting is 24 hours. During the last minute, the minute minder is displayed in seconds. After the set time expires, the oven will automatically stop operating (end of cooking). An acoustic signal will be heard which you may turn off by touching any key. After one minute, the acoustic signal will be switched off automatically. All timer functions can be cancelled by setting the time to "0".
STEP 4: SSELECTING ADDITIONAL FUNCTIONS Activate/deactivate the functions by pressing the desired key or a combination of keys. Some functions are not available with some systems; an acoustic signal will indicate of such cases. CHILD LOCK Activate it by touching the CHILD LOCK key. The "key" icon will light up on the display. Touch the key again to deactivate the child lock. The icon on the display will disappear.
5sek ACOUSTIC SIGNAL Loudness of the acoustic signal can be set when no timer function is activated (only the time of day is displayed). Press the TEMPERATURE key and hold it for 5 seconds. Two fully lit bars will appear on the display. Rotate the SETTINGS KNOB (-/+) to choose one of the three volume levels (one, two, or three bars). After three seconds, the setting will be automatically stored and the time of day will appear.
STEP 5: STARTING THE COOKING PROCESS Start the cooking process by pressing the START/STOP key and holding it for a while. STEP 6: SWITCHING OFF THE OVEN Turn the COOKING SYSTEM SELECTOR KNOB to position "0". 503555 After the end of the cooking process and after the oven has been switched off, declining temperature is displayed down to 50 °C. All timer settings are also paused and cancelled. Time of day (clock) will be displayed. After one minute of idling, the appliance will switch to standby mode.
DESCRIPTIONS OF SYSTEMS (COOKING MODES) AND COOKING TABLES If your desired food cannot be found in the cooking table, find information for similar food. The information displayed applies to cooking in a single level. An interval of suggested temperature is indicated. Start with a lower temperature setting and increase it if you find the food is not browned sufficiently. Cooking times are rough estimates and may vary subject to some conditions.
COOKING SYSTEMS RAPID PREHEATING Use this function to heat the oven to the desired temperature as quickly as possible. This mode is not appropriate for cooking. Turn the COOKING SYSTEM SELECTOR KNOB to rapid preheating. PRESET TEMPERATURE will be displayed. This temperature setting can be adjusted. 503555 When it is switched on, the oven will begin to heat up. The symbol °C will flash on the display. When the set temperature is reached, preheating is completed and an acoustic signal will be sounded.
UPPER AND BOTTOM HEATER The heaters in the bottom and in the ceiling of the oven cavity will radiate heat evenly into the oven interior. 2 Roasting meat: Use enamel coated, tempered glass, clay, or cast iron pan or tray. Stainless steel trays are not suitable as they strongly reflect the heat. Use enamel coated, tempered glass, clay, or cast iron pan or tray. Stainless steel trays are not suitable as they strongly reflect the heat.
Baking pastry Only use one level and dark baking sheets or trays. In light-coloured baking sheets or trays, the browning of the pastry will be poorer, as such equipment will reflect the heat. Always place the baking trays on the grid. If you are using the supplied baking sheet, remove the grid. Cooking time will be shorter if the oven is preheated.
Tip Use Is the cake done? • Pierce the cake at the top with a wooden toothpick or skewer. If there are no traces on the pick or the skewer when pulled out, the cake is done. Did the cake collapse? • Check the recipe. • Next time, use less liquid. • Note the mixing time when using small mixers, blenders etc. The cake is too light at the bottom? • Use a dark-coloured baking sheet or tray. • Place the baking sheet one guide lower and switch on the lower heater towards the end of the cooking progress.
LARGE GRILL, GRILL When grilling food with the large grill, the upper heater and the grill heater fitted on the ceiling of the oven cavity will operate. When grilling food, the upper heater and the grill heater fitted on the ceiling of the oven cavity will operate. Preheat the infrared (grill) heater for five minutes. Supervise the cooking process at all times. The meat may burn quickly due to high temperature.
Grilling table – large grill Type of food Weight (g) Guide (from the bottom) Temperature (°C) Cooking time (minutes) Beefsteak, rare 180 g / piece 3 240 14-16 Beefsteak, well done 180 g / piece 3 240 18-21 Pork neck fillet 180 g / piece 3 240 19-23 Cutlets/chops 180 g / piece 3 240 20-24 Veal escalope 180 g / slice 3 240 19-22 Grill sausages 100 g / piece 3 240 11-14 Spam (Leberkäse) 200 g / piece 3 240 9-15 600 3 240 19-22 MEAT FISH Salmon steaks/fillets TOASTED
Cooking with the rotisserie (depending on the model) Maximum temperature when using the rotisserie is 240°C. 1 Insert the skewer support into the 3rd guide from the bottom and place the deep tray into the bottom (1st) guide to serve as a drip tray. 2 Impale the meat on the skewer and tighten the screws. 3 Place the skewer handle on the front skewer support and insert the tip into the opening in the right hand side of the rear oven cavity wall (the opening is protected with a rotating cover).
GRILL WITH FAN In this operating mode, the grill heater and the fan operate simultaneously. Suitable for grilling meat, fish, and vegetables. (See descriptions and tips for GRILL.
HOT AIR AND BOTTOM HEATER The bottom heater, the round heater, and the hot air fan will operate. Suitable for baking pizzas, apple pies, and fruitcakes. 2 Food Guide (from the bottom) Temperature (°C) Cooking time (minutes) Cheesecake, short crust 2 150-160 65-80 Pizza * 2 200-210 15-20 Quiche Lorraine, shortcrust 2 180-200 35-40 Apple pie, leavened dough 2 150-160 35-40 Apple strudel, phyllo dough 2 170-180 45-65 503555 2 (See descriptions and tips for UPPER and BOTTOM HEATER.
Roasting with a meat probe (depending on the model) In this mode, set the desired temperature of the food core. The oven operates until the food core reaches the set temperature. Temperature core is measured by the temperature probe. 1 Remove the metal cap (the socket is in the front upper corner of the oven right wall). 2 Connect the meat probe plug to the socket and stick the probe into the food. (If any timer settings were activated, they will be cancelled.
During cooking, the rising temperature of the core will be displayed (the desired core temperature may be adjusted during the cooking process). When the set core temperature is reached, the cooking process will stop. An acoustic signal will be heard which you may turn off by touching any key. After one minute, the acoustic signal will be switched off automatically. Clock will appear on the display. After the cooking process, replace the metal cap of the meat probe socket.
HOT AIR Round heater and the fan will operate. The fan installed in the back wall of the oven cavity makes sure the hot air constantly circulates around the roast or pastry. 2 Roasting meat: Use enamel coated, tempered glass, clay, or cast iron pan or tray. Stainless steel trays are not suitable as they strongly reflect the heat. Provide enough liquid during the cooking process to prevent the meat from burning. Turn the meat during roasting. The roast will remain juicier if you cover it.
Baking pastry Preheating is recommended. Biscuits and cookies can be baked in shallow baking sheets on several levels simultaneously (2nd and 3rd). Note that baking time can differ even with if the baking sheets used are the same. The biscuits in the upper baking sheet may be ready sooner than those in the lower one. Always place the baking trays on the grid. If you are using the supplied baking sheet, remove the grid. For even browning, make sure the biscuits are of the same thickness.
BOTTOM HEATER AND FAN This is used for baking leavened but lowrising pastry and for preserving fruit and vegetables. Use the second guide from the bottom and a rather shallow baking tray to allow the hot air to circulate across the upper side of the dish.
Food Amount (L) T = 170 °C – 180 °C until bubbles appear in the jars / until liquid in the jars starts to simmer Temperature at the start of simmering – when bubbles appeared Resting time in the oven (min) FRUIT Strawberries 6×1 l 40-55 switch off 25 Stone fruits 6×1 l 40-55 switch off 30 Fruit mush 6×1 l 40-55 switch off 35 Pickled gherkins 6×1 l 40-55 switch off 30 Beans, carrots 6×1 l 40-55 120°C, 60min 30 503555 VEGETABLES 39
DEFROSTING In this mode, the air will circulate without any heaters operating. Food suitable for defrosting includes cakes with heavy cream or butter-based cream, cakes and pastry, bread and rolls, and deep-frozen fruit. Turn the COOKING SYSTEM SELECTOR KNOB to defrosting. TIME will be displayed. This time setting can be adjusted. Press the START key. In most cases, it is recommended to remove the food from the packaging (do not forget to remove any metal clamps or clips).
MAINTENANCE & CLEANING Be sure to unplug the appliance from the power supply and wait for the appliance to cool down. Children should not clean the appliance or perform maintenance tasks without proper supervision. Aluminium finish Clean the aluminium finish with non-abrasive liquid cleaners intended for such surfaces. Apply the cleaner onto a wet cloth and clean the surface. Then, rinse the surface with water. Do not apply the cleaner directly onto the aluminium finish.
CONVENTIONAL OVEN CLEANING You may use the standard cleaning procedure to clean stubborn dirt in the oven (using cleaners or an oven spray). After such cleaning, rinse the cleaner residues thoroughly. Clean the oven and the accessories after each use to prevent the dirt from burning into the surface. The easiest way to remove fat is by using warm soapsuds while the oven is still warm. With stubborn dirt and grime, use conventional oven cleaners.
AUTOMATIC OVEN CLEANING – PYROLYSIS For average use of the oven, we recommend running the pyrolysis function once per month. Wipe the oven and the accessories to be cleaned in the oven with a damp cloth! Chunks of food and fat may ignite during the pyrolysis process. Danger of fire! Before pyrolytic cleaning, remove all accessories from the oven. 1 Turn the COOKING SYSTEM SELECTOR KNOB to "P". Cleaning intensity level and time are displayed. 2 Choose the desired cleaning intensity.
REMOVING AND CLEANING WIRE AND TELESCOPIC EXTENDIBLE GUIDES Only use conventional cleaners to clean the guides. A Hold the guides by the bottom side and pull them towards the center of the oven cavity. B Remove them from the openings at the top. Do not clean the extendible guides in the dishwasher.
INSTALLING THE CATALYTIC INSERTS Only use conventional cleaners to clean the guides. Remove the wire guides or extendible guides. 1 Mount the guides onto the catalytic insert. 2 Hang the inserts with guides attached using the holes provided, and pull upwards. When installing fully extendible guides with catalytic inserts, insert one end of the supplied snap locks into the openings at the bottom of the oven cavity wall and insert the other end of the snap locks into the guides.
REMOVING AND INSERTING THE OVEN DOOR SOFT DOOR CLOSING (depending on the model) Oven door is fitted with a system that dampens the door closing force, starting at the 75-degree angle. It allows simple, quiet, and smooth closing of the door. A gentle push (to a 15-degree angle relative to the closed door position) is enough for the door to close automatically and softly. If the force applied to close the door is too strong, the effect of the system is reduced or the system will be bypassed for safety.
DOOR LOCK (depending on the model) Open the door lock by gently pushing it to the right with your thumb while simultaneously pulling the door outwards. 503555 When the oven door is closed, the door lock automatically returns to the initial position.
REMOVING AND INSERTING THE OVEN DOOR GLASS PANE Oven door glass pane can be cleaned from the inside, but it has to be removed first. Remove the oven door (see chapter "Removing and replacing the oven door"). 1 Slightly lift the supports on the left and right side of the door (marking 1 on the support) and pull them away from the glass pane (marking 2 on the support). 2 Hold the door glass pane by the lower edge; slightly lift it so that it is no longer attached to the support; and remove it.
REPLACING THE BULB The bulb is a consumable and therefore not covered by warranty. Before changing the bulb, remove the trays, the grid, and the guides. Use a Phillips (cross) screwdriver. (Halogen lamp: G9, 230 V, 25 W; regular bulb E14, 25 W, 230 V) Use a flat screwdriver to release the bulb cover and remove it. Remove the bulb. Be careful not to damage the enamel. Undo the bulb cover and remove the bulb. 503555 Use protection to avoid burs.
TROUBLESHOOTING TABLE Problem/error Cause There is no response of the sensors; the display is frozen. Disconnect the appliance from the power mains for a few minutes (undo the fuse or switch off the main switch); then, reconnect the appliance and switch it on. The main fuse in your home trips often. Call a service technician. The oven lighting does not work. The process of changing the light bulb is described in the chapter Cleaning and Maintenance. The pastry is underdone.
DISPOSAL Packaging is made of environmentally friendly materials that can be recycled, disposed of, or destroyed without any hazard to the environment. To this end, packaging materials are labelled appropriately. The symbol on the product or its packaging indicates that the product should not be treated as normal household waste. The product should be taken to an authorized collection center for waste electric and electronic equipment processing.
COOKING TEST Food tested in compliance with the EN 60350-1 standard.
Grill Dish Equipment Toast* Wire shelf/ grid Minced meat patty (pljeskavica)* Wire shelf (support grid) + shallow baking sheet as drip tray Guide (from the bottom) System Temperature (°C) Cooking time (minutes) 4 240 1:10-1:20 4 240 20-25 503555 * Preheat for 6 minutes.
503555 54
EVP_MULIT_IL+_PIR en (08-15)
