EN DETAILED INSTRUCTIONS HOW TO USE YOUR DRYER www.gorenje.
We thank you for the confidence you have shown us by purchasing this dryer. Your new dryer complies with the requirements of modern laundry care; it will dry your laundry quickly, leaving it soft and smooth, while use of special programs will not deform it. SensoCare technology will allow simple operation of the dryer with very low power consumption. This appliance is designed exclusively for household use for clothes which may be drying in a dryer.
TABLE OF CONTENTS 4 SAFETY PRECAUTIONS INTRODUCTION 8 APPLIANCE 9 Technical information 10 Control panel description 12 12 15 16 17 18 18 19 20 20 INSTALLATION AND CONNECTION Selecting the room Installation Condensate discharge Electrical connections Moving and transport Subsequent transport Emptying the steam generator tank Ionizer system Steam generator system GETTING STARTED 21 BEFORE THE FIRST USE 24 24 25 28 31 34 34 DRYING STEPS (1 - 6) 1. Step: Check the tags on your laundry 2.
SAFETY PRECAUTIONS Please don´t use the appliance unless you have studied and understood the instruction manual. Your dryer is intended solely for household use. If the dryer is used for professional, for-profit purpose or purpose exceeding normal use in a household, or if the dryer is used by a person who is not a consumer, the warranty period shall be equal to the shortest warranty period required by relevant legislation.
Never stop the drying cycle before it is completed; if you do interrupt the cycle for any reason, be careful when removing the laundry from the drum as it is very hot. Quickly remove the laundry from the drum and spread it to allow it to cool down as quickly as possible. 349758 The appliance is manufactured in compliance with all effective safety standards.
CHILDREN UNDER 3 YEARS SHOULD BE KEPT AWAY FROM THE MACHINE UNLESS THEY ARE NOT CONSTANTLY SUPERVISED AT ALL TIMES. THE APPLIANCE IS MANUFACTURED IN COMPLIANCE WITH ALL RELEVANT SAFETY STANDARDS. THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED.
TO REDUCE FIRE HAZARD, PLEASE READ THE FOLLOWING INSTRUCTIONS: Do not dry in the dryer any laundry, that has not been washed earlier. Use the dryer only to dry laundry that was washed with water. Do not dry any laundry that was washed of cleaned with inflammable cleaners or substances (such as gasoline, trichloroethylene etc.) as this may result in an explosion.
APPLIANCE (DRYER DESCRIPTION) FRONT 2 1 3 1 2 3 4 5 6 7 8 Program selector dial Control panel Condensate tank Door Net filter Heat pump filter Air vent Rating plate 4 5 8 7 6 BACK 1 2 3 Condensate discharge pipe Power cord Adjustable feet 1 2 3 3 349758 3 8 3
TECHNICAL INFORMATION (DEPENDING ON THE MODEL) The rating plate with the basic information on the dryer is located under the door frame.
CONTROL PANEL DESCRIPTION FOR MODELS A) WITH A STEAM GENERATOR AND B) WITHOUT A STEAM GENERATOR A) WITH A STEAM GENERATOR 2a 4 2b 2c 3 1 START|PAUSE 1 START/ PAUSE key, use this key to start or stop the program. When selected, the signal light on the key will flash. When the program has started it will be lit continuously. 349758 10 2 a , b , c : SIGNAL LIGHTS are on: when it is necessary to clean the filter, empty the condensate tank or when the child lock is on.
5a 5b 6 5c 90' 5 a , b , c : ADDITIONAL FUNCTION keys, to extend or adjust the basic programs.
INSTALLATION AND CONNECTION SELECTING THE ROOM 10 cm 5 cm 10 cm Ventilation slots and the opening on the front and rear side should always be kept free. Do not install the appliance in a room where there is danger of frost. The room in which the appliance is installed should be adequately ventilated, with temperature between 10°C and 25°C. When the dryer is operated at a lower ambient temperature, condensate can accumulate in the appliance interior.
POSITIONING THE APPLIANCE 4X Positioning the appliance on top of the washing machine by using the vacuum feets or side by side. Dryer can be stand freely on the floor or on a washing machine of the same dimensions – minimum width 517 mm, minimum depth 476 mm. The surface on which the dryer is placed should be clean and level. Use the vacuum feet attached; they are designed to prevent the dryer from sliding.
Do not place the dryer behind lockable or sliding door or door with a hinge opposite the dryer. Install the dryer in such way that the door can always be freely opened. Never block the cool air opening (see dryer description). Drying machine on top should be placed by at least two persons. Do not place the dryer on a carpet with long fibres as this may impede air circulation. The appliance may not be in contact with a wall or adjacent furniture.
INSTALLATION Level the dryer in longitudinal and traverse direction by rotating the adjustable feet which allow levelling by +/- 1 cm. Use key nr. 22 and spirit level. Floor on which the machine is placed must have a concrete base. They must be clean and dry; otherwise, the machine may slide. Also clean the adjustable feet. The appliance must stand level and stable on a solid base.
CONDENSATE DISCHARGE The moisture from the laundry is extracted in the condenser unit and accumulated in the condensate tank. During the drying process, a control light will warm you of a full condensate tank which has to be emptied. Interruption of the drying cycle due to full condensate tank can be avoided by running the condensate discharge tube found at the back of the appliance directly into a drain.
ELECTRICAL CONNECTIONS 2h The dryer should be left to stand still for at least two hours before it is connected to the power mains to allow the system to stabilize. Use the power cord to connect the dryer to the power mains through a power outlet. The dryer may not be connected to the power mains through an extension cable (danger of overheating and fire). Nominal voltage and other information is given on the rating plate located under the door frame.
MOVING AND TRANSPORT If the dryer cannot be transported in the upright position, tilt it to the left side. If the appliance was not transported in compliance with the instructions, the dryer should be left to stand still at least two hours before it is reconnected to the power mains. Failure to do so may result in a heat pump failure which shall not be covered by the warranty. Be careful not to damage the cooling system.
EMPTYING THE STEAM GENERATOR TANK (ONLY FOR MODEL WITH STEAM GENERATOR) Before transporting a dryer that has been previously used, the steam generator tank must also be emptied. Otherwise, water from the tank may spill into the dryer interior. Move the dryer approximately 40 cm away from the wall and tilt it backwards. 1 The steam generator tank emptying plug is located on the front side (lower right hand side). 2 Place an empty vessel under the plug (approximately 2 l) and pull out the plug.
IONIZER SYSTEM (CERTAIN MODELS ONLY) Ionizer adds negative ions into the dryer drum, which has a positive effect on the laundry. The fibre will be flexible and your clothes will be tender and easy to iron. The process takes place during the drying programs. STEAM GENERATOR SYSTEM (DEPENDING ON THE MODEL) Care and treatment of your laundry with steam. Use steam to straighten the creases and refresh the laundry.
BEFORE THE FIRST USE Open the disconnected dryer by pressing the door on the left side. 2 Clean the dryer drum before using the dryer for the first time. Use a damp cloth and a mild cleaning agent.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME (FOR MODEL WITH STEAM GENERATOR) If you select one of the steam programs as the first program to be run with your dryer, first add distilled water to the steam generator tank; the dryer needs the distilled water to generate steam. If the steam generator tank is empty, none of the steam programs will be available. "LO" (steam generator tank empty) will appear on the display.
FILLING AND REPLENISHING THE STEAM GENERATOR TANK (FOR MODEL WITH STEAM GENERATOR) 2 1 Remove the condensate tank. 1 2 Slowly add distilled water to the steam generator tank filter By slowly pouring, you will prevent the water from flowing down the front wall of the appliance. (Steam generator tank is not visible as it is located in the dryer interior; only the steam generator tank filter is visible.
DRYING STEPS (1 - 6) 1. STEP: CHECK THE TAGS ON YOUR LAUNDRY Normal wash Delicate wash Whitening Max. washing 95°C Max. washing 60°C Max. washing 40°C Max. washing 30°C 95 60 40 30 95 60 40 30 Whitening in cold water Manual washing Washing not allowed Whitening not allowed c1 Dry cleaning Dry cleaning in all solvents A Perchloretyhlene R11, R113, Petrolej P Dry cleaning in kerosene, in pure alcohol and in R 113 Dry cleaning not allowed F Ironing Hot iron max. 200°C Hot iron max.
2. STEP: PREPARING THE LAUNDRY Sort the laundry by type and thickness of the fabric (see Program Table). Close the buttons and zips, tie any ribbons, and turn the pockets inside out. Place very sensitive clothes in a special-purpose laundry washing bag. (The special-purpose textile bag is available separately.
DRYING IN A BASKET (ONLY WITH SOME MODELS) Prior to first drying remove the basket and any wrappings from the drum. Drying in a basket may be selected only at time defined drying. Mount the basket in the opposite order of the procedure for its removal, but without the transport packaging. The basket drying function is used to dry sneakers or other things which you want to prevent from tumbling within the drum (max. load: 2,5 kg). Dry only clean sneakers.
SWITCHING ON THE DRYER Connect the appliance to the power mains by plugging in the power cord. To light up the drum (certain models only), rotate the program selector dial to any position. 1 2 LOADING THE DRYER Open the dryer door by pressing it on the left side towards the dryer. Insert the laundry into the drum (make sure the drum is empty). Do not insert laundry into the dryer if it has not been wrung or spun (recommended minimum spinning cycle: 800 rpm). 349758 Close the dryer door.
3. STEP: SELECTING A PROGRAM To select a program, rotate the program selector dial (6) to the left or to the right (according to the type of desired level of dryness of the laundry). Model a) with Steam generator 6 90' 30' 6 Model b) without Steam generator 6 During operation, the dial will not rotate automatically.
PROGRAM TABLE MODEL WITH STEAM GENERATOR Program Dryness levels Max. load Laundry Extra functions Cotton 7 kg/ 8 kg/ 9 kg Non-delicate cotton laundry (towels, terry towels, stockinette, T-shirts, trousers, kitchen cloths etc.) • • • • Start delay Extra dry Anticrease extra Steam (only with cotton – storage dry) 3,5 kg/ Clothing made of a mixture of fibres 3,5 kg/ (trousers, T-shirts, suits etc.
PROGRAM TABLE MODEL WITHOUT STEAM GENERATOR Program Dryness levels Max. load Laundry Extra functions Cotton 7 kg/ 8 kg/ 9 kg Non-delicate cotton laundry (towels, terry towels, stockinette, T-shirts, trousers, kitchen cloths etc.) • • • • Air ionizer Start delay Extra dry Anticrease extra 3,5 kg/ 3,5 kg/ 3,5 kg Clothing made of a mixture of fibres (trousers, T-shirts, suits etc.
4. STEP: ADDITIONAL FUNCTIONS (EXTRA) Activate/deactivate the function by pressing the relevant key (before pressing the START/PAUSE key). 5a 5b 5c 5b 5b 5c 5b + 5c Extra dry Each time the key is pressed (three levels), the final level of laundry dryness and drying time will change. Steam (depending on the model), for straightening the creases and refreshing the laundry with steam, only for programs in which steam treatment is possible.
4 3 3 Start delay Use this function to start the drying cycle after a certain amount of time has elapsed. Delay time can be set to up to five hours in 30-minute steps and up to 24 hours in 1-hour steps. The function is activated when the START/PAUSE key is pressed. Time is counted down by minutes. When the countdown reaches zero, the selected drying program will start automatically. To interrupt or change the program delay time press the START/ PAUSE key. Press the (3) key to select a new delay time.
SOUND SIGNAL LEVEL Select the acoustic signal loudness by simultaneously pressing a key (5a) and rotating the program selector dial clockwise to the initial position. Each time the key (5a) is pressed, the final loudness level is changed (three levels). Loudness level is indicated on the display unit. The most recent setting is stored.
5. STEP: PROGRAM START-UP Press the START/PAUSE key. Start delay time (if selected), or the time remaining until the end of the program and counting down will be indicated on the display unit. Signal lights next to the selected functions will be lit. 6. STEP: END OF DRYING CYCLE An acoustic signal will indicate the end of the drying cycle. Signal lights will light up and the light on the START/PAUSE key will flash. 1. 2. 3. 4. 5. 6. 7. Open the dryer door. Clean the filters (see section Cleaning ...).
CLEANING AND MAINTENANCE The dryer is fitted with a filtering system composed of several filters that prevent any impurity to enter the heat exchanger system. 1 2 Net filter Heat pump filter 1 2 349758 The dryer should never be operated without the filters in place, or with damaged filters as excessive amount of accumulated fibres from the fabric could cause malfunction or failure of the dryer.
CLEANING THE FILTER ON THE LOWER SIDE OF THE DOOR OPENING (CERTAIN MODELS ONLY) Before emptying the drum, clean the filter on the lower door opening using your hand or a damp cloth 1 If the filter is clogged and requires washing, remove it from the support bed. 2 Rinse it under running water, and dry it. Make sure the filter snaps back into place before you close the filter cover.
CLEANING THE NET FILTER IN THE DOOR 1 Lift the filter cover. 2 Scrape the filter cover to remove the layer of lint and threads. 3 Close the filter cover. Close the filter cover in the door always carefully not to crush your fingers. If necessary, clean the filter housing and door gasket as well. 349758 Clean the net filter after each drying cycle.
CLEANING THE HEAT PUMP FILTER Place an absorbent cloth on the floor in front of the dryer (possible water spill). 1 Open the outer cover (hold the handle on the left side and pull downwards 2 Use the handle to remove the heat pump foam filter. 3 Remove the heat pump foam filter from its handle. Use a damp cloth to clean the heat pump housing. Be careful not to damage the cooling system. 4 Wash the filter under running water. Dry the filter before replacing it.
CLEANING THE STEAM GENERATOR TANK FILTER (FOR MODEL WITH STEAM GENERATOR) Each time you empty the condensate tank, clean the steam generator tank filter as well. The filter is located in the tank housing (visible when the condensate tank is removed). 1 Remove the condensate tank. 2 Remove the filter from the support bed in the condensate tank housing. 3 Clean the filter thoroughly under running water. If necessary, clean the filter support bed as well.
EMPTYING THE CONDENSATE TANK Empty the condensate tank after each drying cycle. 1 Remove the condensate tank and turn it. 2 Pour out the water and put the tank back to its place. (2) Pull out the spout for easier emptying (only some models) Water from the condensate tank is not potable. If thoroughly filtered, it can be used for ironing. Never add any chemical means or scents or perfumes into the condensate tank. Make sure you disconnect the appliance from the power mains before cleaning.
CLEANING THE DRYER Wipe the dryer exterior using a damp cloth and mild detergent. Do not use detergents or cleaners that could damage the dryer (heed the recommendations and warnings by the cleaner/detergent manufacturers). Use a soft cloth to wipe dry all parts of the dryer. Always disconnect the dryer from the power mains before cleaning. 349758 Additional equipment and facilities for maintenance can be seen on: www.gorenje.
INTERRUPTING AND CHANGING THE PROGRAM INTERRUPTIONS CHANGING THE PROGRAM/ Interrupting the program process FUNCTIONS Press the START/PAUSE key to pause/ resume and the program. Open door If the dryer door is opened during the drying process, the drying cycle will be interrupted. When the door is closed and the START/ PAUSE key is pressed, the drying will resume from the point at which it was interrupted.
WHAT TO DO...? Disturbances from the environment (e.g. the power grid) may result in various error reports. (see Table on the next page) In such case: • • • • • switch off the appliance and wait at least one minute; switch on the appliance and restart the drying program. If the error persists, call an authorized service unit. You will be able to solve most of the problems in dryer operation by yourself. Repairs may only be carried out by an adequately trained person.
Problem/error Cause What to do ...? The dryer does not work. • No voltage in the power outlet • Check if the power cord plug is correctly inserted into the power outlet. • Check the fuse. There is voltage in the outlet, but the drum does not spin and the dryer does not work. • Program was not started in accordance with the instructions. • The door is not properly closed. • Condensate tank is full. • Delayed start function has been selected. • Reread the instructions for use again.
TIPS AND RECOMMENDATIONS FOR DRYING AND ECONOMIC USE OF YOUR DRYER The most economical way of drying is to dry the recommended amount of laundry in each batch (see Program Table). Drying laundry made of particularly delicate fabrics that may be deformed is not recommended. Use of conditioner in the washing cycle is not necessary as the laundry is soft and smooth after drying in the dryer.
DISPOSAL Packaging is made of environmentally friendly materials that can be recycled, disposed of, or destroyed without any hazard to the environment. To this end, packaging materials are labelled appropriately. The symbol on the product or its packaging indicates that the product should not be treated as normal household waste. The product should be taken to an authorized collection center for waste electric and electronic equipment processing.
TYPICAL CONSUMPTION TABLE The table lists the values for remaining moisture, drying time and power consumption for drying of a test batch of laundry with various spinning rpm in the washing machine (with the 'Cottons Standard' program selected).
SP10 CLASS HP en (03-15)
