MT IE Instructions for use, installation, GB and connection Electric built-in cooking hob
Electric built-in cooking hob Dear customer! Electric built-in hob is intended for use in households. Our products are packed in environment-friendly materials which can be recycled, disposed of, or destroyed without imposing any burden on the environment. Instructions for use Instructions for use are intended for the user. They describe the appliance and its operation.
Important warnings • Installation of the appliance into a kitchen worktop and its connection to the power mains may only be performed by an adequately qualified technician. • Do not leave small children unattended when the appliance is in operation. Risk of burning and scalding! • During cooking, the overheated fat or oil on the hob may ignite. There is a risk of burning and fire; therefore, control the cooking process at all times. • Do not use the cooking hob for room heating.
Appliance description The following figure shows the surface of the hob with electric hotplates. Type EVK4... 1. 2. 3. 4. 5. Type EVK6...
Cooking zones Turn on the cooking zones for 3 to 5 minutes and select the maximum power level; some fumes may be discharged from the hob. This way, the protective cover on the cooking hob will reach its maximum solidness.
Energy saving • Pan bottom diameters should match the diameter of the cooking zone. If the pan is too small, some heat is wasted; furthermore, using a too small pan can damage the cooking zone. • Whenever possible given the cooking process, use a lid. • The pan should be appropriately sized given the quantity of food prepared. Preparing a small quantity of food in a large pan will cause a waste of energy. • Dishes that take a long time to cook should be prepared in a pressure cooker.
Cleaning and maintenance • Clean the appliance using warm water, liquid detergent, and a soft cloth. • Do not use any abrasive or sharp utensils or other objects. Burnt or dried food residues should be moistened using a damp cloth and softened with appropriate detergent. • Stainless steel parts should be cleaned using special-purpose detergents. Use a dry, highly-absorbent cloth to apply a thin layer of detergent on a dry and cool surface, and rub gently in the direction of surface treatment pattern.
Special warnings and fault reporting During the warranty period, only a service center authorized by the manufacturer may carry out any repairs. Before making any repairs, make sure the appliance is disconnected from the power mains either by removing the fuse or by disconnecting the power plug from the wall outlet. Unauthorized tampering with and repairs of the kitchen range (cooking hob) can result in electric shock or short circuit; hence, do not attempt to perform any repairs by yourselves.
Installation Important warnings • Installation of the appliance into a kitchen worktop and its connection to the power mains may only be performed by an adequately qualified technician. • Veneer or other finish of the piece of kitchen furniture into which the hob is to be built in should be treated with heat resistant glue (100°C); otherwise, the worktop finish may be discolored or deformed.
Type EVK6.. • Only type EVP4, EVP2... ovens fitted with a cooling fan may be installed underneath this cooking hob. • Before installing an oven, the rear wall of the kitchen furniture element should be removed in the area of the cooking hob cutout. Furthermore, a gap of at least 6 mm should be left at the front side. Installation procedure • The worktop should be installed completely horizontally. • The cutoff surfaces should be appropriately protected.
Connecting the appliance to the power mains Important warnings • • • • • • • • • The appliance may only be connected by an authorized skilled technician. Electric system protection should comply with all relevant regulations. The connection clips can be accessed when the connection clip covers are opened / removed. Before connecting the appliance, make sure the voltage indicated on the rating plate is consistent with the voltage in your home circuit.
NOTE: Connection bridges are already installed on their respective places on the clip. Screws of the connection terminals are open, which means they do not have to be unfastened or unscrewed any further. When fastening the screws, you may hear a slight ‘click’, which means that the screws should be fastened / screwed in completely. The following can be used for connection: • Type H05 RR-F 4×1.
Technical characteristics Rating plate Serial number Code Model Type Trademark Technical information Compliance indications / symbols WE RESERVE THE RIGHT TO MAKE ANY CHANGES THAT DO NOT AFFECT THE FUNCTIONALITY OF THE APPLIANCE.
252584 14
EVK6,4K 252584/en (04-10)