Operation Manual

ManualsBrandsGorenje ManualsHobect 680 al

Instructions for use, mounting and connection

Built-in ceramic-glass cooktop GB IE MT

Dear customer !

The built-in ceramic-glass cooktop is intended for

household use only.

Materials used for packaging are nature friendly

and may be recycled, deposited or destroyed

without any threats to the environment.

In order to recognize these features, all packing

materials are marked with relevant symbols.

Once your appliance has become obsolete and

you do not intend to use it any longer, take

adequate care not to litter the environment.

Deposit your old appliance with the authorized

depot dealing with used household appliances.

Instructions for use

Instructions for use have been prepared for the

user, and describe the particulars and handling of

the appliance. These instructions apply to

different models from the same family of

appliances, therefore you may find information

and descriptions that may not apply to your

particular appliance.

Installation instructions

The appliance should be connected to the power

supply in accordance with the instructions from

the chapter "Electrical connections" and in line

with the standing regulations and standards.

The connections should be carried out by a

qualified personnel only.

Rating plate

The rating plate with basic information is located

underneath the appliance.

Fire hazard protection

Appliances are allowed to be mounted on one

side next to a high kitchen cabinet, the height of

which may exceed that of the appliance. On the

opposite side however, only a kitchen cabinet of

equal height as the appliance is allowed.

Built-in ceramic-glass cooktop EN .............. 40

Important warnings ...................................... 41

Connection to the power supply .................. 41

Basic adjustment of sensors to the ambience

Installation diagram

Mounting the built-in cooktop ..................... 42

Caution !

Dimensions of the built-in hob opening

Installation procedure

Ceramic-glass cooktop.................................. 43

Cookware ....................................................... 44

Energy saving tips

Glass ceramic hob control elements ............ 45

Control panel

Control elements

Automatic cooking mode

Blocking the hob operation

Timer function

Limited time of operation

Safety functions and error display

Cooker controls.............................................. 52

Control panel

Control elements............................................ 53

Switching the hob on

Selecting the particular hotplate

Switching the hotplate on

Automatic cooking mode

Blocking the hob operation

Remaining heat indicators

Switching the entire hob off

Limited operation time

Power interruption

Safety warnings and error indication

Cleaning and maintenance of ceramic-glass

hob .................................................................. 56

Technical information................................... 57

Summary of content (18 pages)

PAGE 1
Built-in ceramic-glass cooktop Dear customer ! GB IE MT Instructions for use The built-in ceramic-glass cooktop is intended for household use only. Materials used for packaging are nature friendly and may be recycled, deposited or destroyed without any threats to the environment. In order to recognize these features, all packing materials are marked with relevant symbols. Once your appliance has become obsolete and you do not intend to use it any longer, take adequate care not to litter the environment.
PAGE 2
Important warnings • The appliance may be built-in and connected to the power supply only by a qualified technician. • Particular areas of the cooktop surface (adjacent to the hotplates) are hot during operation. Prevent the children to hang around the appliance and warn them properly against the danger of burns. • Hot oil ignites readily, so be sure have the preparation of such food (fries) under constant control. • Hotplates may not be left in operation empty, without any dishes on top.
PAGE 3
Basic adjustment of sensors to the ambience Upon each connection to the power supply the sensors of the appliance are automatically adjusted to the environment to ensure their proper function. All displays indicate the sign "-". Once the successful adjustment is completed it is signaled with a beep, all displays are switched off and your cooktop is ready for use.
PAGE 4
• The smallest distance between the edge of the appliance and the adjacent high kitchen cabinet is 40 mm. • The use of hard wood decorative borders around the worktop behind the appliance is allowed, in case the minimum distance remains as indicated on the installation illustrations. • Minimum distance between the built-in cooktop and rear wall is indicated at the illustration for the installation of the built-in cooktop. • The appliance may be installed in any worktop with a thickness from 30 mm to 50 mm.
PAGE 5
Cookware Use only high quality cookware with flat and firm bottom. • Position the pot at the center of the hotplate during cooking. • When using the fireproof and temperature resistant glass cookware observe the instructions of the producer. • If the pressure cooker is used to prepare food, have it under constant control throughout the cooking until proper pressure has been obtained.
PAGE 6
Glass ceramic hob control elements Control panel Extended hotplate ring ON/OFF sensor Second hotplate LED signal lamp (hotplate 4) Second and third hotplate LED signal lamp (hotplate 2), certain models Heating power setting indicator (0...
PAGE 7
Control elements Once the glass ceramic hob is connected to the mains (including the power failure), the appliance carries out the harmonization with the conditions of the exterior in order to provide most efficient sensor function and render the best control environment. After the successful accommodation to the environment, the indicators show the mark "-" for a moment which eventually disappear. The sound signal confirms the appliance is ready for use.
PAGE 8
Setting of cooking level As long as the indicators are lit the heating power (1...) may be selected and altered accordingly by pressing the (-) or (+) sensor. By the (+) sensor the power is gradually increased to the maximum level (9), while with the (-) sensor it is reduced back to 0 (hotplate is switched off).
PAGE 9
Switching the extended hotplate rings on (hotplates 2 and 4) Switch the relevant hotplate ( 2 or 4) and consequently switch the extended hotplate ring by pressing the relevant sensor (see the control element board illustration). The LED signal lamp above the indicator displays the extended ring is on. Now select the random heating power for both hotplate rings together.
PAGE 10
Switching the hotplate off Particular hotplate is switched off either by pressing the sensor (-) to bring the heating power to "0", or by simultaneously pressing both the (+) and (-) sensor. Hotplate is switched off automatically after the set timer period elapses. Display indicates "0" for a short time, then the hotplate is switched off and the indicator displays the remaining heat "H".
PAGE 11
Timer function Once the hob is on you have two timer operation alternatives: 1. time countdown without the switch off function 2. setting the timer controlled period of operation for a particular hotplate Timer is activated by pressing the timer sensor, the display indicates "00". Set the time between 1 and 99 minutes: this setting may be altered at any time in 1 minute intervals by pressing the (+) or (-) sensor. Constant press of either sensor changes the setting faster, in 5 minute intervals.
PAGE 12
Limited time of operation This function is incorporated for safer operation of your hob. Each hotplate is equipped with the time limit switch. The period of operation is calculated in accordance with the last selected power setting of a particular hotplate. If the power setting is not changed for a while, the hotplate will be switched off automatically after a certain period of time, depending upon the power setting level (higher power setting – shorter time see chart).
PAGE 13
Cooker controls Control panel Hotplate cooking power indicator (0…9), remaining heat warning ''H'', and automatic cooking mode indicator ''A'' 2 3 1 4 Hotplates 1 - 4 Hotplate selection sensor (+) Hotplate ON and power increase sensor (-) Hotplate ON and power reduction sensor Blocked operation indicator Main switch ON/OFF sensor Blocked operation ON/OFF sensor 52 Instructions for use, mounting and connection
PAGE 14
Control elements Once the glass ceramic hob is connected to the mains (including the power failure), the appliance will perform the process of initial synchronization with the exterior environment, in order to provide the most efficient sensor function and render the best control. you may select the desired cooking power in 10 seconds following the switch on or selection of a particular hotplate.
PAGE 15
Switching the hotplate on Once the hotplate is selected and its indicator flashes ''0'', you have 10 seconds to select the desired power setting by pressing either sensor (+) or (-). Indicator will flash the selected setting, and after 10 second lapse this setting becomes default. If no power setting is selected within 10 seconds, the indicator ''0'' goes off and the hotplate is switched off. Power setting 1 2 3 4 5 6 7 8 Maximum power time (in sec.
PAGE 16
Switching the hotplate off Particular hotplate is switched off either by pressing the sensor (-) to bring the heating power to "0", or by simultaneously pressing both the (+) and (-) sensor. Display indicates "0" for a few seconds, then the hotplate is switched off and the indicator displays the remaining heat "H". If you wish to switch off the inactive hotplate, first activate it by touching the hotplate selection sensor, then follow the above procedure.
PAGE 17
Safety warnings and error indication If both the (+) and (-) sensor are preset together the hotplate is switched off. If all the hotplates indicate the "0" power setting, the hob is switched off after 10 seconds. If any of the sensors is activated for more than 10 seconds the hob is switched off and the indicators display the flashing "F" signal. If the sensors are covered with an object, or the surface is covered with spilt liquid, the hob is switched off.
PAGE 18
Major stains are removed with special ceramicglass cleansers. Follow strictly the manufacturer's instructions. Be careful to remove any remains of cleansing agent from the hob surface, otherwise they will be heated during the next use and can damage the hob (fig. 3). Stubborn and burnt stains are removed with special ceramic-glass scraper. Be careful, however, not to touch the hotplate surface with the scraper handle (Fig. 4).