Operation Manual

ManualsBrandsGorenje ManualsHobect 890 e

136356

The built-in ceramic-glass cooktop is intended for household use

only.

Materials used for packaging are nature friendly and may be

recycled, deposited or destroyed without any threats to the

environment. In order to recognize these features, all packing

materials are marked with relevant symbols.

Once your appliance has become obsolete and you do not

intend to use it any longer, take adequate care not to litter the

environment. Deposit your old appliance with the authorized

depot dealing with used household appliances.

Instructions for use have been prepared for the user, and

describe the particulars and handling of the appliance. These

instructions apply to different models from the same family of

appliances, therefore you may ﬁ nd information and descriptions

that may not apply to your particular appliance.

The appliance should be connected to the power supply in

accordance with the instructions from the chapter “Electrical

connections” and in line with the standing regulations and

standards. The connections should be carried out by a qualiﬁ ed

personnel only.

The rating plate with basic information is located underneath the

appliance.

Appliances are allowed to be mounted on one side next to a

high kitchen cabinet, the height of which may exceed that of the

appliance. On the opposite side however, only a kitchen cabinet

of equal height as the appliance is allowed.

Important warnings ................................................... 20

Ceramic-glass cooktop ............................................. 21

Energy saving tips..................................................... 23

Glass ceramic hob control elements ....................... 24

Cleaning and maintenance of ceramic-glass hob .. 31

Connection to power supply .................................... 32

Mounting the built-in cooktop .................................. 33

Tehnični podatki ........................................................ 35

Dear customer !

Instructions for use

Installation instructions

Rating plate

Fire hazard protection

Built-in ceramic-glass cooktop

Summary of content (17 pages)

PAGE 1
SI EN Dear customer ! The built-in ceramic-glass cooktop is intended for household use only. Materials used for packaging are nature friendly and may be recycled, deposited or destroyed without any threats to the environment. In order to recognize these features, all packing materials are marked with relevant symbols. Once your appliance has become obsolete and you do not intend to use it any longer, take adequate care not to litter the environment.
PAGE 2
Important warnings • The appliance may be built-in and connected to the power supply only by a qualified technician. • Particular areas of the cooktop surface (adjacent to the hotplates) are hot during operation. Prevent the children to hang around the appliance and warn them properly against the danger of burns. • Hot oil ignites readily, so be sure have the preparation of such food (fries) under constant control. • Hotplates may not be left in operation empty, without any dishes on top.
PAGE 3
Ceramic-glass cooktop 1. Rear left hotplate 2. Front left hotplate 3. Front right hotplate 4. Rear right hotplate 5. Hob control module 6. Warming-up hotplate Control panel 136356 A Ceramic hob main switch sensor B1 Warming up hotplate signal LED B Warming up hotplate ON/OFF sensor C Blocked operation sensor C1 Blocked operation control lamp D Extended hotplate ring ON/OFF sensor D1 Second hotplate LED signal lamp (hotplate 4) E Heating power setting indicator (0...
PAGE 4
Ceramic-glass cooktop is equipped with four hotplates designed as cooking zones. The surface of the hob is flat, without any edges for eventual gathering of dirt. Cookware may easily be moved about along the hob surface. • Hotplates quickly reach the selected heating power while the adjacent area around the hotplates remains cool. • Warming up hotplate warms up slowly and reaches the temperature of around 100° Celsius. • The cooktop is resistant to temperature changes.
PAGE 5
The cooking zone may be damaged: • if it is left in operation without any cookware being placed on top, or if covered with empty cookware; • if improper cookware is used: unevenly flat bottom or small diameter (traditional Turkish coffee kettle). • the use of terra-cotta (clay) cookware is likely to produce scratches upon the ceramic-glass surface. • Before placing any cookware upon the cooktop thoroughly wipe the bottom dry, thereby improving the heat conduction and protecting the hotplate from damage.
PAGE 6
Glass ceramic hob control elements • Once the glass ceramic hob is connected to the mains (including the power failure), the appliance carries out the harmonization with the conditions of the exterior in order to provide most efficient sensor function and render the best control environment. • Do not place any objects upon the sensor surface during the accommodation period, otherwise you may provoke error mode. In such cases the process is interrupted and the appliance signals error.
PAGE 7
Switching the hotplates on • Once the hob is switched on with the ON/OFF sensor, within the next ten seconds, while the indicators are illuminated, you have to switch on a particular hotplate by touching the (-) or (+) sensors for the selected hotplate and set the desired heating power. If the power setting is not selected within the next ten seconds, the “0” indicator turns off and the hotplate will automatically be switched off.
PAGE 8
Power setting 1 2 3 4 5 6 7 8 Switching the extended hotplate rings on (hotplates 2 and 4) Maximum power time (in seconds) 82 164 246 328 410 82 164 164 • Switch the relevant hotplate ( 2 or 4) and consequently switch the extended hotplate ring by pressing the relevant sensor (see the control element board illustration). The LED signal lamp above the indicator displays the extended ring is on. Now select the random heating power for both hotplate rings together.
PAGE 9
• Warming up hotplate is intended for keeping dishes with already cooked food on a warm plate. It is not intended for cooking or for heating of cold food. • The hotplate is switched on and off by touching the relevant sensor. When the hotplate is active the signal LED above the sensor is on. • Warming-up hotplate warms up slowly and reaches the temperature of around 100° C, so beware of burns, and do not place any temperature sensitive objects upon its surface.
PAGE 10
Remaining heat display • Immediately after a particular hotplate is switched off, or in case the complete hob is switched off, the indicator shows the letter “H” as a warning that the “hotplate is hot”. The period of this warning signal is calculated in accordance with the working time and the power setting of the hotplate. When the warning signal is on do not touch the hotplate or place any temperature sensitive objects on the relevant hotplate.
PAGE 11
Countdown of preset time • By activating the timer (indicator “00”) you have switched on the time countdown By touching the (+) sensor the countdown starts with 1 minute, and increases in one minute intervals. By pressing the sensor (-) the countdown starts from 99 minutes. Desired time is selected by pressing either the (+) or (-) sensor. Preset time may be changed at random during the countdown. The expiry of selected time is signaled by the beep for a few seconds.
PAGE 12
depending upon the power setting level (higher power setting – shorter time - see chart). Power setting 1 2 3 4 5 6 7 8 9 Warming-up hotplate Safety functions and error display Maximum operation time in hrs 10 5 5 4 3 2 2 2 1 10 • If both the (+) and (-) sensor are preset together the hotplate is switched off, even if the operation is blocked. • If all the hotplates indicate the “0” power setting, the hob is switched off after 10 seconds.
PAGE 13
Cleaning and maintenance of ceramic-glass hob fig. 1 fig. 2 fig. 3 fig. 4 Ceramic glass hob should be cleaned only when completely cooled down, preferably after each use, otherwise even the slightest stains remaining after cooking may burn into the hob surface with each following use. For regular maintenance of ceramic-glass hob use special cleansing agents, produced in such way to create protective film upon the surface.
PAGE 14
Connection to power supply • Connections may be carried out by a qualified technician only. The earthing protection must comply with the standing regulations. • Connection terminals are revealed when the connection box cover is removed. • Prior any attempted connection check that the voltage indicated on the rating plate is in line with your home power supply. • The rating plate is located underneath the appliance. • The appliance is manufactured for use with the power supply voltage AC 230 V.
PAGE 15
Installation diagram NOTE: Connection screws are already in the open position, so they need no unscrewing. During the tightening procedure you will hear a faint “click”, meaning that the tightening screw should be fastened tightly all the way. Connection may be carried out by means of: - rubber coated connection cables, model H05 RR-F 4x1,5 with yellow-green earthing cable; - PVC insulated connection cables, model H05 VV-F 4x1,5 with yellow-green earthing cable; or - any other suitable cables.
PAGE 16
• The appliance may be installed in any worktop with a thickness from 30 mm to 50 mm. • In case there is a drawer in kitchen cabinet under the built-in hob, it is necessary to install an additional horizontal barrier of height 6 cm under the hob and above the drawer. Dimensions of the builtin hob opening Installation procedure 136356 34 • Worktop must be placed absolutely horizontal. • Suitably protect the edges of the cut aperture.
PAGE 17
Tehnični podatki Type SVK81TS Electrical connection Working voltage Type of switch SVK82TS 2N AC 400 V 230 V, 50 Hz Electronic sensors Cooking hotplates (ø mm/kW) HL= Hi-light cooking zone Warming-up hotplate cona Total power (kW) 210/175/120/2,3/HL 145/1,2/HL 170x265/2,4/HL 145/1,2/HL 210/175/120/2,3/HL 145/1,2/HL 180/120/1,7/HL 145/1,2/HL 160x290/0,1/R 160x290/0,1/R 7,1 6,4 WE RESERVE THE RIGHT TO ALTER THE SPECIFICATIONS WITH NO INFLUENCE TO THE OPERATION OF THE APPLIANCE.