MT AT DE Gebrauchs-, Einbau- und Anschlußanweisung IE GB Instructions for use, mounting and connection Glaskeramik-Einbau-Kochfeld Ceramic glass integrated cooking hob
Ceramic glass integrated cooking hob GB IE MT Dear customer! The built-in ceramic-glass cooktop is intended for household use only. Materials used for packaging are nature friendly and may be recycled, deposited or destroyed without any threats to the environment. In order to recognize these features, all packing materials are marked with relevant symbols. Once your appliance has become obsolete and you do not intend to use it any longer, take adequate care not to litter the environment.
Important warnings The appliance may be built-in and connected to the power supply only by a qualified technician. Particular areas of the cooktop surface (adjacent to the hotplates) are hot during operation. Prevent the children to hang around the appliance and warn them properly against the danger of burns. Hot oil ignites readily, so be sure have the preparation of such food (fries) under constant control.
Ceramic glass hob surface 1 - front cooking zone 2 - rear cooking zone 3 - front cooking zone - duo-zone 4 - control panel Hob control elements A - sensor for disabling of function (key) B - sensor of power switching on/off C - sensor for minus (-) D - sensor for plus (+) F – indicator light of hotplate disabling I – indicator light for coupling of duo-zone outer circuit K – sensor for duo-zone L - sensor of cooking zone M - display for heating capacity level N – symbol for activation of cooking zone 18
Ceramic-glass cooktop is equipped with four hotplates designed as cooking zones. The surface of the hob is flat, without any edges for eventual gathering of dirt. Hotplates quickly reach the selected heating power while the adjacent area around the hotplates remains cool. The cooktop is resistant to temperature changes. The cooktop is also impact resistant. Cookware may be placed upon the surface rather firmly without any consequences. Avoid using the hob as a working surface.
The cooking zone may be damaged: if it is left in operation without any cookware being placed on top, or if covered with empty cookware; if improper cookware is used: unevenly flat bottom or small diameter (traditional Turkish coffee kettle). the use of terra-cotta (clay) cookware is likely to produce scratches upon the ceramic-glass surface. Before placing any cookware upon the cooktop thoroughly wipe the bottom dry, thereby improving the heat conduction and protecting the hotplate from damage.
Hob controls CALIBRATION OF SENSORS During time period, when the sensors are adapting to the external conditions: Do not put objects on their surface as the failure mode could be activated. Keep always the sensors' surface clean. Do not expose them to excessive light, as for instance halogen lamp or direct sunlight etc. The sensors could be calibrated incorrectly at unobserving of these conditions and a failure message appears on the display (see the table).
THE SETTING UP OF CAPACITY LEVEL WITH PREHEATING FUNCTION: Capacity level U 1 2 3 4 5 6 7 8 9 It is used for simplification of cooking with faster bringing of food in boiling with full capacity level followed with automatic switching to selected lower capacity level. Activate the corresponding cooking zone. Press the sensor for „-“, the number "9" and the letter "A" blink alternately on the display.
SWITCHING OFF OF COOKING ZONE Activate the corresponding cooking zone. The cooking zone is switched off with synchronous pressing of sensors D (+) and C (-) or witch pressing of sensor C (-) up to achieving of „0“ capacity level. The symbol "H" will light on the display of corresponding zone after switching off of cooking zone, where this symbol is calling your attention to the fact, that the zone is hot and the remaining heat can be used.
DEACTIVATION SWITCHING OFF OF CHILD LOCK Switch on the hotplate with pressing of sensor „B“. The displays go on showing the symbol "L". Up to 3 seconds press simultaneously the sensors „+“ and „-“ and thereafter the sensor „-“. The hotplate is now ready for use. AUTOMATIC SWITCHING OFF OF THE HOTPLATE When we switch off the all cooking zones, the hotplate will switch off automatically in 10 seconds.
Cleaning and maintenance of ceramic-glass hob fig. 1 fig.2 fig.3 Ceramic glass hob should be cleaned only when completely cooled down, preferably after each use, otherwise even the slightest stains remaining after cooking may burn into the hob surface with each following use. For regular maintenance of ceramic-glass hob use special cleansing agents, produced in such way to create protective film upon the surface.
Fitting the hob Caution ! To avoid any possible hazard, the appliance may be installed by qualified personnel only. Panels and furniture lining of the kitchen cabinet receiving the hob must be treated with temperature resistant adhesives (100°C), otherwise they might be discoloured or deformed because of inadequate temperature resistance. The cooking hob is intended for building into the worktop above the kitchen element of 600 mm width or more.
Installation procedure Worktop must be placed absolutely horizontal. Suitably protect the edges of the cut aperture. Screw the attached fixing elements 4 with attached screws 4 on the right and the left panel of the hob to the already prepared hole in the opening. Connect the cooking hob to the mains power supply (see instructions for the connection of the cooking hob to mains power supply). Insert the hob into the cut aperture. Press the hob firmly towards the worktop from above.
The appliance is manufactured for connection to the AC 230V mains power. The electric wiring should be equipped with a circuit breaker able to isolate the appliance from the mains in all points, with the distance between terminals of at least 3 mm in open position. This may be done by means of fuses, safety switches, etc. The connection should be selected in accordance with the declared charge capacity of the mains and the fuse power.
Connection may be carried out by means of: • rubber coated connection cables, model H05 RR-F 3x1,5 with yellow-green earthing cable; • PVC insulated connection cables, model H05 VV-F 3x1,5 with yellow-green earthing cable; or any other suitable cables.
PRODUCT INFORMATION REGULATION (EU) NO 66/2014 Symbol Unit Supplier’s name or trade mark Model identification Value GORENJE 430A Value GORENJE 4309 2 2 radiant cooking zones 14,5 18,0/12,0 195,3 190,6 193,0 radiant cooking zones 14,5 18,0 191,9 190,6 191,3 Type of hob Number of cooking zones and/or areas EE electric Heating technology burner The diameters of cooking zones and / or areas Ø Energy consumption per cooking zone or area ECelectric Energy consumption for the hob cm Wh/kg cooking
4309, 430A / DE / AT / GB / IE / MT 2015 01 01 / SAP 282251 30