Instructions for Use GB IE MT
GLASS CERAMIC INDUCTION BUILT-IN COOKING HOB Built-in glass ceramic induction hob is intended solely for use in households. Our products are packed in environment-friendly materials which can be safely recycled, disposed of, or destroyed. Respective packaging materials are labeled accordingly. When the appliance is outdated and you intend to dispose of it, please make sure this is done in an environment-friendly manner. Take it to an authorized collection center for waste household appliances.
TABLE IMPORTANT WARNINGS.................................................................................................5 Safety percautions........................................................................................................................5 Warnings............................................................................................................................................6 CERAMIC-GLASS COOKTOP .............................................................................
IMPORTANT WARNINGS Safety percautions 440291 • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or metal capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Warnings • The appliance may only be connected to the power mains by an authorized service technician or expert. • Tampering with the appliance or non-professional repair thereof may result in risk of severe injury or damage to the product. Any repairs may only be carried out by an authorized service technician or expert. • The appliance is intended solely for cooking. Do not use it for any other purpose, e.g. for room heating. Do not place empty cookware on the cooking zones.
CERAMIC-GLASS COOKTOP 1. Induction hotplate rear 2. Induction hotplate rear right 3. Induction hotplate front left 4. Induction hotplate front right 5.
Induction hotplate function principle • Ceramic glass hob is fitted with three or four hotplates. Hob surface is completely flat and smooth, without edges to accumulate dirt. • The hob is fitted with high power induction hotplates. Heat is generated directly at the bottom of the dish, where it is most needed, without any losses through the ceramic glass surface. This way the required extent of energy is considerably smaller compared to traditional heaters, which operate on radiation principle.
Only use cookware suitable for electric and induction cooking, with a: • thick bottom (at least 2.25 mm) • flat bottom. Cooking zone Minimum pan bottom diameter Ø 160 mm Ø 110 mm Ø 180 mm Ø 110 mm Ø 200 mm Ø 145 mm The magnet test Using a small magnet, it is possible to check whether the bottom of your cookware can be magnetized .Use only cookware to which the magnet will stick. The cooking zone can be damaged: • If an empty pan is placed on it.
Power regulation Power setting 0 1-2 3 4-5 6 7-8 Purpose Off, using remaining heat Maintaining warm food, slow simmer of smaller quantities (lowest setting) Slow simmer (continuation of cooking after a powerful start-up) Slow cooking (continuation) of larger quantities, roasting larger chunks Roasting, browning Roasting 9 Cooking large amounts, searing/braising P “Power boost” setting for start of the cooking process; also suitable for very large amounts of food Energy saving tips 440291 10 Cookin
HOB CONTROL • After connecting the glass ceramic hob to the power mains, all symbols on the display will light up briefly. The cooking hob is then ready for operation. • The cooking hob is fitted with electronic sensors which are activated by touching the designated surface areas with your finger for at least one second. • Each time a sensor is activated, this is confirmed by a beep. • Do not place any objects on the sensor area. Make sure the sensor area is always clean.
Powering off the cooking hob • The cooking hob may be switched off anytime by touching the on/off sensor (A). All settings will be deleted, except for the minute minder (see section »Timer«). A Engaging the control unit lock / child safety lock By activating the control unit lock, you can prevent the operation or use of the cooking zones. Thus, the control unit lock also works as a child safety lock. Activating the child lock • The hob must be switched off.
Warning: The cooking zone with the SP P symbol (Super Power Boost) offers the Super Power Boost function. In this zone, extra power is activated for five minutes; then, it switches to level 9. Activating the Power Boost • Press the relevant sensor (C) to select the cooking zone. Use the »–« or »+« sensor (E) to choose the power level 9; then, press »+« immediately. »P« will appear on the power level display.
• Induction cooking hob is also fitted with a builtin overheating protection device that protects the electronic parts from damage. The protection device operates at several levels. When the cooking zone temperature increases considerably, the cooking power is reduced automatically. If this is not enough, the power of currently heated cooking zones is reduced further or shut off entirely. In this case, “E2” will be indicated on the display.
• Value can be set from 01 to 99 minutes. Shut-off timer can be set for each cooking zone. • To check the remaining time, select the corresponding cooking zone and activate the timer function. Press the »–« or »+« sensor (E) to change the setting. (Press the »–« and »+« sensor (E) simultaneously and sequentially to choose between active settings.) • When the set time expires, »00« will flash on the display; in addition, relevant decimal point will flash at the shut-off timer. A short beep will be heard.
CLEANING AND MAINTENANCE OF CERAMICGLASS HOB Cleaning Figure 1 Figure 2 Figure 3 After each use of the glass-ceramic hob, wait for it to cool down and clean it; otherwise, even the smallest food residue will be burnt onto the hot surface next time you use the appliance. For regular cleaning and maintenance of the glass-ceramic surface, use special conditioning agents which form a protective layer on the surface, shielding it from dirt.
Figure 5 Sugar and sugar-laden food may permanently damage the glass-ceramic surface (Figure 5); therefore, they should be removed from the glass-ceramic surface as soon as possible, although the cooking zone may still be hot (Figure 4). Any change in the color of the glass-ceramic surface does not affect its operation or the stability of the surface.
Installing the foam gasket Before inserting the appliance into the opening in the kitchen worktop, the supplied foam gasket must be attached to the lower side of the glass ceramic (glass) cooking hob (see figure above). Do not install the appliance without the foam gasket! The gasket should be attached to the appliance in the following way: - Remove the protective film from the gasket.
Worktop cutout dimensions - SIVK6 • Cooking hobs can be installed into worktops that are 30 to 50 mm thick. • If the board is thicker than 40 mm, its inner edge should be trimmed, or ground (Figure A). Thus, sufficient air circulation will be provided. • If the thickness of your counter top exceeds 30 mm, then the opening for the hob should be made in the middle of the oven, with sufficient clearance from the front edge of the counter top so that the induction hob does not touch the oven shield.
Lower kitchen cabinet ventilation slots • To enable normal operation of electronic components of the induction hob, sufficient air circulation must be provided. A Lower kitchen cabinet with a drawer • An opening at least 140 mm high must be provided on the back wall of the cabinet, along its entire width. Furthermore, a minimum of 6 mm clearance must be provided at the front side, along the entire width of the cabinet. • The hob is fitted with a fan located in its lower part.
440291 B Lower kitchen cabinet with an oven • Installing the oven under an induction hob is possible with oven types EVP4.., EVP2.., which are fitted with a cooling fan. Before installing the oven, the rear wall of the kitchen cabinet should be removed. Furthermore, a minimum of 6 mm clearance should be provided at the front side, along the entire width of the cabinet.
Installation diagram The appliance is designed for two-phase connection; it can also be connected to a single phase. • Two-phase connection Install the jumper connectors on terminals 4 and 5. • Single-phase connection Install the jumper connectors on terminals 4 and 5, and terminals 1 and 2. Note: Connection 3 is free.
CONNECTION TO THE POWER SUPPLAY • Connections may be carried out by a qualified technician only. The earthing protection must comply with the standing regulations. • Connection terminals are revealed when the connection box cover is removed. • Prior any attempted connection check that the voltage indicated on the rating plate is in line with your home power supply. • The rating plate is located underneath the appliance. • The appliance is manufactured for use with the power supply voltage 230 V ~.
Single-phase connection with total power limiter (only in model with four cooking zones) • If your home main fuse does not allow 32-ampere current, then the function of total power limiter can be activated on the hob so that the current never exceeds 16 A. • If you activate the total power limiter, then the power of each cooking zone may only be increased until total power reaches the limit. When the limit is reached, the hob will beep and the setting display will flash.
TECHNICAL INFORMATION Rating plate Serial number Code Model Type Trademark Technical information Compliance indications / symbols WE RESERVE THE RIGHT TO ALTER THE SPECIFICATIONS WITH NO INFLUENCE TO THE OPERATION OF THE APPLIANCE.
440291 26
www.gorenje.
