Bedienungsanleitung Operating Instructions SSL-Last-KONSTANTER Serie/Series 32 EL Elektronische Last Electronic Load 3-349-362-15 6/10.
SSL Last-Konstanter Serie 32 EL Inhaltsverzeichnis Sicherheitshinweise ........................................... 2 Elektronischer Last-Konstanter Software .... 19 Kapitel 1 Einleitung ......................................... 5 Kapitel 1 Systeminstallation ........................... 20 1.1 Einleitung .................................................. 5 1.2 Technische Daten ...................................... 5 1.3 Merkmale .................................................. 6 1.
SSL LAST-KONSTANTER SERIE 32 EL Sicherheitshinweise Achtung Diese Betriebsanleitung beinhaltet alle zum Personenschutz, zum Schutz der Elektronischen Last und zum Schutz der angeschlossenen Geräte notwendigen Sicherheitsvorkehrungen. Die nachfolgenden allgemeinen Sicherheitsvorkehrungen müssen während des Betriebs, der Wartung und der Instandhaltung dieses Geräts immer eingehalten werden.
SSL LAST-KONSTANTER SERIE 32 EL II Anschließen der Netzzuleitung 1. Überprüfen Sie den Spannungsumschalter auf der Rückseite des Geräts, um sicherzustellen, dass die gewählte Spannung der verfügbaren Netzspannung entspricht. Wenn dies nicht der Fall ist, beachten Sie bitte die am Netzeingangsstecker des Gerätes gedruckten Hinweise und achten Sie auf Einsatz der richtigen Sicherung. 2.
SSL LAST-KONSTANTER SERIE 32 EL ACHTUNG Vor Inbetriebnahme des elektronischen Last-Konstanters DC muss die Erdklemme des Geräts an den Schutzleiter der AC-Netzleitung angeschlossen werden. WEITERE SICHERHEITSHINWEISE Die folgenden allgemeinen Sicherheitshinweise sind während des gesamten Betrieb sowie bei allen Wartungs- und Reparaturarbeiten am Gerät zu befolgen.
SSL LAST-KONSTANTER SERIE 32 EL Kapitel 1 Einleitung 1.1 Einleitung Der SSL Last-Konstanter Serie 32 EL ist eine programmierbare elektronische DC Last mit einem Eingang. Es lassen sich damit Gleichstromversorgungen und Batterien bequem testen. D e r L a s t Konstanter bietet Konstantstrom-, Konstantwiderstand und Konstantleistungsmodus. Zudem ist die Programmbedienung und Steuerung ü b e r P C m ö g l i c h .
SSL LAST-KONSTANTER SERIE 32 EL 1.3 Merkmale 1. hinterleuchtete LCD Anzeige 2. Hochauflösende Messungen 3. CC/CP/CR Modus 4. Numerisches Tastenfeld und Drehknopf 5. Multifunktionsmenü 6. Überspannung / Überstrom / Leistungsbegrenzung / Übertemperatur / Verpolungsschutz 7. 10-stufiger Programmablauf 8. Kompakte Bauform und geringes Gewicht 9. in Parallelschaltung verwendbar 10. PC-steuerbar 1.4 Abmessungen und mechanischer Aufbau 1.4.
SSL LAST-KONSTANTER SERIE 32 EL 1.4.2 Mechanischer Aufbau 1.4.2.1 Frontansicht Die Bedienfrontplatte ist mit einer LCD Anzeige, einem numerischen Tastenfeld und einem Drehknopf ausgestattet (vgl. Abbildungen unten zur Detailansicht). Bild 1-2 Frontansicht des elektronischen SSL LastKONSTANTERS, Serie 32 EL Obere Zeile: Strom, Spannung, Ein/Aus-Zustand 1.
SSL LAST-KONSTANTER SERIE 32 EL 3. Drehknopf und Funktionstasten : Pfeiltaste nach links : Pfeiltaste nach rechts ESC: Escape-Taste (Abbruch) OK: Bestätigungstaste Drehknopf für Sollwerteinstellung Bild 1-5 Drehknopf und Funktionstasten 1.4.2.
SSL LAST-KONSTANTER SERIE 32 EL Kapitel 2 Bedienung 2.1 Schließen Sie die zu prüfende Gleichspannungsquelle an den elektronischen Last-Konstanter an. Bild 2-1 Schließen Sie die DC-Spannungsquelle an die elektronische Last an 2.2 Hauptfunktionen 1. Konstantstrommodus 2. Konstantleistungsmodus 3. Konstantwiderstandmodus 4. Programm speichern 5. Programm abrufen 6. Programm starten 7. Programm beenden 8. Last ein-/ausschalten 2.2.
SSL LAST-KONSTANTER SERIE 32 EL Einstellen des Konstantstroms: Ablauf Bedienung LCD Anzeige Schritt 1 Drücken Sie “I-set” Input Password Input Password Schritt 2 Geben Sie das Passwort ein ( M a s t e r - P a s s w o r t : 1 5 5 6 ) oder rücken Sie weiter zu Schritt 4 wenn das Tastenfeld freigegeben ist. Schritt 3 Drücken Sie die “OK”-Taste (wenn das Passwort nicht korrekt ist, springt die Anzeige zu Schritt 2 zurück zur erneuten Eingabe). Set Curr = 2.
SSL LAST-KONSTANTER SERIE 32 EL (2)Wenn das Tastenfeld passwortgeschützt ist: Schritt 1.
SSL LAST-KONSTANTER SERIE 32 EL Einstellen des Konstantwiderstands: Ablauf Schritt 1 Schritt 2 LCD-Anzeige Bedienung Drücken Sie “R-set” Input Password Geben Sie das Passwort ein (Master-Passwort: 1556) Input Password oder rücken Sie weiter zu Schritt 4, wenn das Tastenfeld freigegeben ist. Schritt 3 **** Drücken Sie die “OK ”-Taste. Der vorher eingestellte Wert Set Resis = 200.
SSL LAST-KONSTANTER SERIE 32 EL 2.2.5 Programm abrufen Um ein Programm abzurufen, das im SSL KONSTANTER 32 EL gespeichert wurde, gehen Sie wie nachfolgend beschrieben vor: Ablauf Bedienung Schritt1 Schritt 2 LCD-Anzeige Drücken Sie die “ Recall ”-Taste RECALL 1 Geben sie die Programmnummer (1 bis 9) ein, entweder über RECALL * die numerischen Tasten oder mit Hilfe des Drehknopfs. Drücken Sie die “ OK ”-Taste zur Bestätigung.
SSL LAST-KONSTANTER SERIE 32 EL 2.3.1 Einstellen des maximalen Stroms Dieser Parameter definiert den oberen Grenzwert des Stromeinstellbereichs. Wenn Sie die Funktion „Maximum Current“ wählen, erscheint folgende Anzeige auf der LCD: Max Curr=****A New= Sie können den Stromwert über das numerische Tastenfeld oder mit Hilfe des Drehknopfs einstellen. Bestätigen Sie den Wert mit der “OK”-Taste. 2.3.
SSL LAST-KONSTANTER SERIE 32 EL 2.3.5 Einstellen der Adresse (0~254) Diese Funktion dient zur Eingabe der Geräteadresse. Um mit einem Computer oder anderen Geräten kommunizieren zu können, muss dem SSL Last-KONSTANTER 32 EL eine Adresse zugewiesen werden. Wenn Sie die Funktion „Set Address“ wählen, erscheint folgende Anzeige auf der LCD: Set Address=*** New= Geben Sie die A dresse mit Hilfe des numerischen Tastenfeldes oder des Drehknopfes ein. Bestätigen Sie den Wert mit der „OK“-Taste.
SSL LAST-KONSTANTER SERIE 32 EL Der Programmablauf ist wie folgt dargestellt: 1、Wählen Sie die Funktion „Programm Set“ aus dem Menü. Auf der LCD erscheint folgende Anzeige: Constant Curr Constant Power Wählen Sie den Konstantstrommodus mit Hilfe der AUFund AB-Pfeiltasten oder dem Drehknopf aus. Drücken Sie „OK“ zur Bestätigung. Constant Resis 2、Auf der LCD erscheint: Step Number=* New= Geben Sie die Anzahl der Programmschritte “3” ein und drücken Sie „OK” zur Bestätigung.
SSL LAST-KONSTANTER SERIE 32 EL 9、Auf der LCD erscheint: One Time Wählen Sie „Repeat“ und drücken Sie „OK” zur Bestätigung. Repeat Die Programmierung ist damit abgeschlossen. Drücken Sie “ESC”, um zum Hauptmenü zurückzukehren, drücken Sie „Start“ um das Programm ablaufen zu lassen. Wie Sie das Programm für zukünftige Nutzung speichern können, ist unter Punkt 2.2.4 beschrieben. 2.3.
SSL LAST-KONSTANTER SERIE 32 EL 18 GMC-I Messtechnik GmbH
SSL LAST-KONSTANTER SERIE 32 EL Elektronischer Last-Konstanter Software ElectronicLoad ist eine kostenlose Software zur Überwachung und Steuerung des elektronischen SSL Last-KONSTANTERS Serie 32 EL.
SSL LAST-KONSTANTER SERIE 32 EL Kapitel 1 Systeminstallation 1.1 Anschließen der elektronischen Last an den PC Mit dem optionalen Schnittstellenadapter können Sie den SSL-KONSTANTER 32 EL a n I h r e n C o m p u t e r üb e r d i e RS-232-, USB- oder RS-485-Schnittstelle a n s c h l i e ß e n .
SSL LAST-KONSTANTER SERIE 32 EL 1.2.2 Das Willkommens-Dialogfenster erscheint. Drücken Sie “ NEXT ”, um fortzufahren. Bild 1-3 Willkommens-Dialogfenster 1.2.3 Das Dialogfenster für die Lizenzvereinbarung erscheint. Klicken Sie auf „Yes“, um der Lizenzvereinbarung zuzustimmen und fahren Sie mit dem Installationsprozess fort. Achtung: Wenn Sie der Lizenzvereinbarung nicht zustimmen, drücken Sie auf „No“, um den Installationsprozess abzubrechen. Bild 1-4 Dialogfenster zur Lizenzvereinbarung 1.2.
SSL LAST-KONSTANTER SERIE 32 EL 1.2.5 Das Dialogfenster Zielverzeichnis erscheint. Das voreingestellte Verzeichnis lautet “ C:\Program Files\Array\ELoad ”. Wenn Sie ein anderes Installationsverzeichnis auswählen möchten, klicken Sie auf “Browse”. Bild 1-6 Dialogfenster Zielverzeichnis 1.2.6 Das Dialogfenster mit den Installationsoptionen erscheint. Wählen Sie “Typical”, um alle Komponenten zu installieren oder ”Custom”, um einzelne Installationskomponenten zu installieren.
SSL LAST-KONSTANTER SERIE 32 EL 1.2.8 Kopieren Sie die Dateien auf Ihre Festplatte. Bild 1-9 Kopieren der Dateien Die Systeminstallation ist abgeschlossen, sobald das Kopieren beendet ist.
SSL LAST-KONSTANTER SERIE 32 EL Kaptitel 2 Einführung in die Funktionen 2.1 Programm starten 2.1.1 Um das ElectronicLoad Programm zu starten, wählen Sie “Start=>Programme =>Array=>Eload” und klicken Sie auf “E3710A” oder E3711A”. Bild 2-1 Programm starten 2.1.2 Programmstartfenster für die Elektronische Last Bild .
SSL LAST-KONSTANTER SERIE 32 EL 2.1.3 Hauptfenster für die Elektronische Last Bild 2-3 Hauptfenster für die Elektronische Last 2.2 ELoad Liste Die Eload Liste listet alle auf dem Computer registrierten elektronischen Lasten auf. Wählen Sie die gewünschte Last aus der Eload Liste aus, um Ihre Last von der ElectronicLoad Software steuern zu lassen. Bild 2-4 Die Eload Liste 2.3 Lastmodus-Liste Aus der Lastmodus-Liste können Sie den Lastmodus auswählen: Konstantstrom, Konstantleistung, Konstantwiderstand.
SSL LAST-KONSTANTER SERIE 32 EL 2.5 Werkzeugschaltflächen Oben links im Hauptfenster befinden sich 9 Werkzeugschaltflächen: “Start”: Kommunikation starten “Stop”: Kommunikation beenden “Setting”: COM-Schnittstelle und Aufzeichnunsintervall einstellen “Program”: Programm einstellen “Run Program”: Programmablauf starten “Stop Program”: Programmablauf beenden “Eload Setting”: Lastparameter einstellen “Report”: Datenprotokoll erstellen “Quit”: Electronic Load Programm verlassen 2.
SSL LAST-KONSTANTER SERIE 32 EL Strom einstellen: Drücken Sie “I set”, geben Sie den Stromwert ein (0~30A) und drücken Sie zur Bestätigung die ENTER-Taste. Leistung einstellen: Drücken Sie “P set”, geben Sie den Leistungswert ein (3710A: 0~150W¸3711A: 0~300W) und drücken Sie zur Bestätigung die ENTER-Taste. Widerstand einstellen: Drücken Sie “R set”, geben Sie den Widerstandswert ein (0~500Ω) und drücken Sie zur Bestätigung die ENTER-Taste.
SSL LAST-KONSTANTER SERIE 32 EL 2.9 Einstellungen 2.9.1 Einstellen von Com-Schnittstelle und Baudrate Klicken Sie auf die - Taste, um die richtige Com-Schnittstelle und Baudrate auszuwählen. Die eingestellte Baudrate sollte mit der Baudrate der angeschlossenen elektronischen Last übereinstimmen. Bild 2-12 Einstellfenster 2.9.2 Einstellen der Lastadresse Bild 2-13 Einstellfenster für die Adresse Klicken Sie auf “Address”, um zum Adresseinstellfenster zu gelangen.
SSL LAST-KONSTANTER SERIE 32 EL 2.9.
SSL LAST-KONSTANTER SERIE 32 EL 2.10 Programmierfenster: Die ElectronicLoad Software ermöglicht es dem Anwender, eigene Programme zur Steuerung des SSL KONSTANTERS 32 EL zu erstellen. Der Anwender kann den Lastmodus auswählen, den Lastwert für Strom, Leistung und Widerstand sowie die Dauer des jeweiligen Programmschrittes bestimmen. Klicken Sie auf die -Taste.
SSL LAST-KONSTANTER SERIE 32 EL Die Eload Registrierungsdaten zeigen die Parameter aller registrierten Lasten. Wenn Sie eine neue Last hinzufügen möchten, klicken Sie auf die Taste . Bild 2-17 Hinzufügen eines neuen Lastfensters Geben Sie den Namen und die Adresse der Eload ein sowie die Maximalwerte für Strom, Leistung, Widerstand. Bestätigen Sie die Eingabe mit „OK“. Anmerkung: die Eload ID wird von der Software vergeben.
SSL LAST-KONSTANTER SERIE 32 EL Bild 2-18 Nach den Funktionen „Add“, „Modify“ und „Delete“ muss das Programm neu gestartet werden 2.12 Datenprotokoll Klicken Sie auf die Taste , um das Datenprotokollfenster aufzurufen: Bild 2-19 Datenprotokollfenster Zum Suchen definieren Sie die Abfrageparameter und klicken auf die Taste „Search“. Klicken Sie die Taste “Report”, um das Protokoll aufzurufen. Klicken Sie auf die Taste “Excel”, um das Protokoll ins Excelformat zu exportieren.
SSL LAST-KONSTANTER SERIE 32 EL 2.13 Steuern der Last über die ElectronicLoad Software Starten Sie das ElectronicLoad Programm aus der Eload-Liste heraus und wählen Sie die Last, die Sie verwenden möchten. Wenn die gewünschte Last nicht in der Eload-Liste aufgeführt ist, fügen Sie sie über die Funktion Eload Einstellungen hinzu. Klicken Sie auf die Einstelltaste . Vergewissern Sie sich, dass die Com-Schnittstelle, die Baudrate und die Adresse mit denen der Last übereinstimmen.
SSL LAST-KONSTANTER SERIE 32 EL Kapitel 3 Deinstallation der ElectronicLoad Software 3.1 Deinstallieren der ElectronicLoad Software Wählen Sie aus dem Startmenü “Program=>Array=>Eload=>Uninstall Eload”, um die Software zu deinstallieren. Denken Sie bitte daran, das Programm zu schließen bevor Sie mit der Deinstallation beginnen.
SSL Load KONSTANTER Series 32 EL Table of Contents SAFETY GUIDE........................................... 2 Electronic Load Software .......................... 19 Chapter 1 General Introduction ................. 5 Chapter 1 Software Installation ............... 20 1.1 General Introduction ................................... 5 1.1 Connect the electronic load to PC ............. 20 1.2 Specifications .............................................. 5 1.2 Installation ...................................
SSL LOAD KONSTANTER SERIES 32 EL SAFETY GUIDE Caution The following general safety precautions must always be adhered to during operation, maintenance and repair of the device. Noncompliance with these safety precautions, or with other explicit warnings included in these operating instructions, is deemed a violation of design-specific safety standards and use for intended purpose. The manufacturer assumes no liability in the event of noncompliance with these safety precautions.
SSL LOAD KONSTANTER SERIES 32 EL II Connecting the Power Cable 1 Examine the voltage selector switch on the back of the device in order to assure that the selected voltage coincides with available mains power. If this is not the case, observe the note printed on the device’s mains inlet plug, and make sure that the correct fuse is utilized. 2 The on/off switch in the device’s front panel must be switched off before the power supply is connected to the mains.
SSL LOAD KONSTANTER SERIES 32 EL CAUTION Before switching on the DC Electronic load, the protective earth terminal of this instru-ment must be connected to the protective conductor of the AC line power cord. The AC lineplug shall be inserted only in a socket outlet provided with a negated by the use of an extensioncord (or power cable) without a protective grounding conductor.
SSL LOAD KONSTANTER SERIES 32 EL Chapter 1 General Introduction 1.1 General Introduction SSL Load KONSTANTER 32 EL series electronic load is a single input programmable DC electronic load. It provides a convenient way to test DC power supplies and batteries. It offers constant current mode, constant resistance mode and constant power mode. Program operation and control by PC is also available. The backlight LCD, numerical keypad and rotary knob make it much easier to use.
SSL LOAD KONSTANTER SERIES 32 EL 1.3 Features 1. LCD display with backlight. 2. High resolution measurement. 3. CC/CP/CR mode. 4. Number keypad and rotary knob. 5. Multifunction menu. 6. Over voltage / over current / over power / over temperature / polarity reversion protection. 7. 10 steps program. 8. Compact and light-weight. 9. Can be used in parallel connection. 10. Can be controlled by PC. 1.4 Dimensions and Structure 1.4.1 Dimensions (unit: mm) Fig.
SSL LOAD KONSTANTER SERIES 32 EL 1.4.2 Structure 1.4.2.1 Front view Front panel is for users to operate, and there is one LCD display, one number keypad and one rotary knob. Please see the following pictures. Fig.1-2 Front view of SSL KONSTANTER 32 EL Series DC electronic load The 1st line: Current, voltage, On/Off state 1. LCD display The 2nd line: Power, load setting value, working mode. Fig.
SSL LOAD KONSTANTER SERIES 32 EL 3. Rotary knob and function keys : The left moving key : The right moving key ESC: Escape key OK: Confirmation key Rotary knob for setpoint adjustment Fig.1-5 Rotary knob and function keys 1.4.2.2 Back view Fig.1-6 Back view The fuse can be changed easily by using a small flat screw driver. Please use a fuse within the range of 0.3-0.5A.
SSL LOAD KONSTANTER SERIES 32 EL Chapter 2 Operation 2.1 Connect the DC voltage source to be tested to the electronic load Fig.2-1 Connect the DC voltage source to the electronic load 2.2 Main functions 1. Constant current mode 2. Constant power mode 3. Constant resistance mode 4. Store a program 5. Recall a program 6. Start a program 7. Stop a program 8. Load On/Off 2.2.
SSL LOAD KONSTANTER SERIES 32 EL Constant current setting procedure: Procedure Operation details Step 1 Step 2 LCD display Press “I-set” Input Password Enter the password ( master password: 1556). If the Input Password k eyboard isn’t locked, please go to step 4. **** Press the “OK” button, the original set value will be displayed on the LCD.
SSL LOAD KONSTANTER SERIES 32 EL (2) If the keyboard is locked Step1. Press “ I-set ” button, Step2. Enter the password by using the number keyboard (master password: 1556) Step3. Press OK button (if the password is wrong, please go to step2 for reentering), Step4. Rotate the Rotary to change the value,the operation is the same as item (1) Step5. Press “ I-set ” button to confirm the current value. 2.2.
SSL LOAD KONSTANTER SERIES 32 EL Constant resistance setting procedure: Procedure Operation details Step 1 Step 2 LCD display Press “R-set” button Input Password Enter the password (master password: 1556). If the Input Password keyboard isn’t locked, please go to step 4. **** Press the “OK ” button, the original set value will be displayed on the LCD. (It will return to step 2 if your Step 3 Set Resis = 200.
SSL LOAD KONSTANTER SERIES 32 EL 2.2.5 Recall a program To recall a program stored in the SSL KONSTANTER 32 EL, please follow this operation procedure: Procedure Operation details Step1 Step 2 LCD display Press “ Recall ” button RECALL 1 Enter the program number (1 to 9) by using the number RECALL * key or the rotary knob Press the “ OK ” button for confirmation. It will return to Step 3 Step 2 if the number is out of the range.
SSL LOAD KONSTANTER SERIES 32 EL 2.3.1 Setting the maximum current This parameter defines the upper limit for the current setting range. When you select the Maximum Current function, the LCD will display: Max Curr=****A New= Set the maximum current value by using the number keyboard or the rotary knob, then press “OK” for confirmation. 2.3.2 Setting the maximum power This parameter defines the upper limit for the power setting range.
SSL LOAD KONSTANTER SERIES 32 EL 2.3.5 Setting Address (0~254) This function is used to set the device address of the load. To communicate with the computer or other equipment, the SSL KONSTANTER 32 EL load must be assigned an address. When you select Address set function, the LCD will display: Set Address=*** New= Set the address by using the number keyboard or the rotary knob, and then press “OK” for confirmation. The valid address range is from 0 to 254. 2.3.
SSL LOAD KONSTANTER SERIES 32 EL Programming procedure is shown below: 1、Select Program Set from menu operation, the LCD will display: Constant Curr Constant Power Use the UP and DOWN keys or rotary knob to select Constant Current mode, and press “OK” to confirm. Constant Resis 2、LCD will display: Step Number=* Input the program length “3” and press “OK” to confirm. New= 3、 LCD will display: Step1 Set=0.00 Input the current value “1”A, then press “OK” to confirm.
SSL LOAD KONSTANTER SERIES 32 EL 9、 LCD will display: One Time Select Repeat, then press “OK” to confirm. Repeat The programming process is completed. Press “ESC” to return to the main menu, press “Start” to run the program. If you want to store this program for later use, please see 2.2.4 2.3.8 Save Option This function is used to save the last load setting (current, power and resistance) before switching off the SSL KONSTANTER 32 EL.
SSL LOAD KONSTANTER SERIES 32 EL 18 GMC-I Messtechnik GmbH
SSL LOAD KONSTANTER SERIES 32 EL Electronic Load Software ElectronicLoad is a free software which allow the user to monitor and control the SSL KONSTANTER 32 EL Series electronic load.
SSL LOAD KONSTANTER SERIES 32 EL Chapter 1 Software Installation 1.1 Connect the electronic load to PC With the optional communication adapter, you can connect the SSL KONSTANTER 32 EL load to your computer through RS-232, USB or RS-485 port. Connect the SSL KONSTANTER 32 EL to a RS-232 port with the 3311 adapter (K910A), to an USB port with the 3312 adapter (K910B) to a RS-485 port with the 3314 adapter (K911B).
SSL LOAD KONSTANTER SERIES 32 EL 1.2.2 The Welcome dialog box displays, press “ NEXT ” to continue Fig.1-3 The Welcome dialog box 1.2.3 The License Agreement dialog box displays. Click Yes to accept the License Agreement and proceed with the installation process. Note: If you do not want to accept the License Agreement, click No to abort the installation process. Fig.1-4 The License Agreement dialog box 1.2.
SSL LOAD KONSTANTER SERIES 32 EL 1.2.5 The destination folder dialog box displays. The default folder is “ C:\Program Files\Array\ELoad ”. You may click “Browse” to select other installation path. Fig.1-6 The destination folder dialog box 1.2.6 The installation option dialog box displays. Select “Typical” to install all components or select ”Custom” to select installation components. Fig.1-7 The installation option dialog box 1.2.7 The Select Program Folder dialog box displays.
SSL LOAD KONSTANTER SERIES 32 EL 1.2.8 Copy the files to your hard disk. Fig.1-9 Copy Files Software installation is complete when finished.
SSL LOAD KONSTANTER SERIES 32 EL Chapter 2 Introduction 2.1 Running the program 2.1.1 To run the ElectronicLoad program, select “Start=>Program=>Array=>Eload” and click “E3710A” or E3711A” to run the program. Fig.2-1 Start the program 2.1.2 The ElectronicLoad startup pattern Fig.
SSL LOAD KONSTANTER SERIES 32 EL 2.1.3 The ElectronicLoad Main Window Fig.2-3 The ElectronicLoad Main Window 2.2 The ELoad List The Eload list lists all registered electronic load on the computer. To make the ElectronicLoad control your load, choose the load you want to use from the Eload list. Fig.2-4 The Eload List 2.3 The Load Mode List From the Load Mode list, you can select Load Mode: Constant Current, Constant Power, Constant Resistance. Fig.2-5 The Load Mode List 2.
SSL LOAD KONSTANTER SERIES 32 EL 2.5 The Tool Buttons On the top left of the main window, there are 9 tool buttons: “Start”: Start communication “Stop”: Stop communication “Setting”: setting COM Port and recording interval “Program”: Setting a Program “Run Program”: Run a Program “Stop Program”: Stop Running Program “Eload Setting”: Setting load parameters “Report”: Data report “Quit”: Quit the ElectronicLoad program 2.6 Keypad and Rotary dial: Fig.
SSL LOAD KONSTANTER SERIES 32 EL Set Current: Press “I set”, input the current value (0~30A), press “ENTER” to confirm. Set Power: Press “P set”, input the power value (3710A: 0~150W¸3711A: 0~300W), press “ENTER” to confirm. Set Resistance: Press “R set”, input the resistance value (0~500Ω), press “ENTER” to confirm. I Max, P Max, R Max: show the max value of each parameter. 2.
SSL LOAD KONSTANTER SERIES 32 EL 2.9 Setting 2.9.1 Setting Com port and baud rate Click the button, select the correct Com port and baud rate. The baud rate setting should be the same as the connected electronic load. Fig.2-12 Setting Window 2.9.2 Setting electronic load address Fig.2-13 Address Setting window Click “Address” to go to the Address setting window. Set an address that is the same as the connected electronic load. Press “OK” to confirm.
SSL LOAD KONSTANTER SERIES 32 EL 2.9.3 Setting Recording Interval Fig.
SSL LOAD KONSTANTER SERIES 32 EL 2.10 Programming Window: ElectronicLoad allows user to make an own program to control the SSL KONSTANTER 32 EL load. User can select the load mode, and define load value (current, power, resistance) and duration of each program step. Click the button, the Program window will be displayed: Fig.2-15 Programming window Select an “Electronic Load Mode”; enter the load value and the duration of each program step. The maximum program length is 10 steps.
SSL LOAD KONSTANTER SERIES 32 EL The Eload Registration Records show the parameters of all registered load. To add a new load, click the button. Fig.2-17 Add new load window Enter the Eload Name, Address and the maximum value of current, power, resistance, then press “OK” to confirm. Note: the Eload ID is assigned by the software.
SSL LOAD KONSTANTER SERIES 32 EL Fig 2-18 After Add, Modify, Delete operation, the program must restart 2.12 Data Report Click the button, the data report window will be shown: Fig 2-19 The Data Report window To search, set the query condition, and then click the “Search” button. Click the “Report” button to watch the report. Click the “Excel” button to export the report in Excel format. To delete historic data, click the “Clear” button. Quit: quit to the main window.
SSL LOAD KONSTANTER SERIES 32 EL 2.13 Use ElectronicLoad software control your load Start the ElectronicLoad program, from the Eload List, select the load you want to use. If the desired load does not appear on the Eload List, use Eload Setting to add the desired load. Click the Setting button, ensure that the Com port, baud rate and address is the same as that of the load.. Click the Start button to start communication.
SSL LOAD KONSTANTER SERIES 32 EL Chapter 3 Uninstall ElectronicLoad Software 3.1 Uninstall the ElectronicLoad Software From the Start Menu, select “Program=>Array=>Eload=>Uninstall Eload” to unstall the software. Remember to quit the program before uninstalling.
Reparatur- und Ersatzteil-Service Kalibrierzentrum* und Mietgeräteservice Repair and Replacement Parts Service Calibration Center * and Rental Instrument Service Bitte wenden Sie sich im Bedarfsfall an: When you need service, please contact: GMC-I Service GmbH Service-Center Thomas-Mann-Straße 20 90471 Nürnberg • Germany Telefon +49 911 817718-0 Telefax +49 911 817718-253 E-Mail service@gossenmetrawatt.com www.gmci-service.