Operating Instructions SECUTEST SI+ 3-349-613-15 5/4.
6 7 5 SECUTEST SI+ 6 8 4 3 2 1 2 MENU without Function 9 10 11 12 13 14 Standard Equipment 1 Input and memory module SECUTEST SI+, 1 USB connector cable, 1 Operating instructions The Driver Control software for installing the USB device driver is available from our website.
1 Ribbon cable with RS232 plug for connection of the SI module to the tester 2 USB socket connector for the transmission of stored data to the PC to shift the keyboard from small letters to capital letters and vice versa 12 Shift key Key , shifts to full stop ( .
Contents Page Page 1 Applications ................................................................................. 6 5 How to Display and Store Reports .............................................12 1.1 1.2 1.3 Application SECUTEST... ..............................................................................6 Application PROFITEST 204 and METRISO 5000 D-PI ....................................7 Meaning of the Symbols on the Unit .............................................................7 5.
Contents Page 9 Error Message ........................................................................... 21 10 Technical Data ........................................................................... 22 11 Maintenance .............................................................................. 25 11.1 11.2 11.3 How to Reset the SI Module ...................................................................... 25 Housing ............................................................................
1 Applications The SI (Storage Interface) module SECUTEST SI+ is a special accessory for the the following test instruments: SECUTEST..., SECULIFE ST, PROFITEST 204 and METRISO 5000 D-PI. It is installed in the lid of the tester and fastened with two knurled screws. The test results determined with the test instrument are directly transferred to the SI module via the ribbon line. 1.1 Application SECUTEST...
USB Device Driver 1.2 The Driver Control software for installing the USB device driver including the operating instructions are available for download from our website Operation with these test instruments is limited to the function „Entry of comments via the alphanumeric keyboard.“ Only the following chapters are relevant in this context: chap. 2 Safety Features and Safety Precautions chap. 3.1 Installing the SI Module chap. 10 Technical Data (without memory function) chap.
2 Safety Features and Safety Precautions When the SECUTEST SI+ is properly used, the safety of both the user and the unit is assured. In order to meet the legal regulations for electromagnetic compatibility (EMC), an electrically conductive plastic material is used for the housing for shielding. Touching of the SI module under normal operation causes no danger as contact-hazardous voltages do not occur in the SECUTEST SI+.
3 Getting Started 3.1 Installing the SI Module ➭ SECUTEST... only: Remove the cover from the lid of the SECUTEST.... For this purpose, press the cover to the side. ➭ Insert the SI module into the lid and fasten it with the two knurled retaining screws. ➭ Connect the module to the connection socket of the RS232 interface of the test instrument via the ribbon cable. ➭ SECUTEST... only: Below the SI module there is a compartment provided in the lid for the storage of the probe lead.
Request menu 4 Press 1x MENU Upon selection of the menu item „Setup“ you can perform the following settings: Selection and execution of the functions listed in the menu is done by means of the corresponding keys on the test instrument. The other operating controls and connectors should remain unchanged while the SI module is active so that the data traffic will not be disturbed. The menu item "Return" causes a return to the LC display presented prior to activating the SI module.
4.2 Enter and Delete Top and Bottom Lines ➭ You will get to the next line by pressing the ENTER key ➭ You can delete the top and bottom lines with the and 4.3 keys Clear Memory To clear the memory, press the ENTER key on the SI module. To stop, press the From the keyboard, you can enter optional texts which – before and/or after the test result – are to be automatically included in the report printout. For top and bottom lines, 5 lines of 24 characters each are available.
5 How to Display and Store Reports Note Storage of the results of the safety and function tests as well as their entry into reports and statistics is only possible after tests have been performed. Exception: the function switch is in the „MENUE“ position (older versions: also „FUNCTION-TEST“). In this position only the result of the last function test can be stored. You can load the result of the last test into the SI module and store it there under an Ident Number.
End the text entry of a line by pressing the ENTER key. At the same time, this brings you to the next line. ➭ To store, press the STORE key. returns you to the SI menu. When storing the report, the consecutive ident number is output between date and time. Figure at left: Info on DUT max. 24 charact. each Figure at right: Info on customer max. 24 charact. each Results of the function test Information on e.g. repair max. 10 lines of max.
If there are no data available in the test instrument when the menu item Protocol is called up, the following message appears: 5.2 Automatic Report Storage All test results are automatically allocated a consecutive ident number* provided the Autostore function is active. After the safety test as well as after the function test, a note is displayed indicating that the test data are being stored.
5.3 Quick Report Storage If many measurements are to be made successively and the results are to be evaluated later, the function "Quick report storage" presents itself. This function can only be performed after a test (safety test and/or function test). ➭ Activate the SI module with STORE . This brings you directly to the enter field for the ident number. Here you can enter a maximum of 24 digits and confirm with ENTER . ➭ To store, press the STORE key once more.
5.4 Requesting Stored Reports A list of all stored reports can be requested at any time in order to display and print out the contents of individual reports at a later date. The first column contains the consecutive numbers, the second one the ident numbers. The first 14 characters of the ident number are shown as a maximum. ➭ Choose Protocol and confirm with . ➭ Press the help key i on the SECUTEST.... A list of the stored reports appears. ➭ Select the desired report using the and keys and confirm with .
6 Statistics Altogether, statistic data of a maximum of eight equipment classes can be recorded. The statistic data include the number of the errors occurred as well as their percentage of the total measurement within one class. The statistics menu appears provided Statistics has been selected in the main menu, see chapter 3.2, page 9. GMC-I Messtechnik GmbH 6.
The safety tests as well as the function tests can now be performed for the selected class. After the start of a report recording, the setting First or All in the statistics menu can no longer be changed. After each complete measurement, consting of safety test and function test, the measured data must be stored so that they will be available for statistic evaluation. See „How to Display and Store Reports“ on page 12.
6.3 Delete Statistic Data ➭ With or , move the cursor to Delete and press . ➭ Select the class the data of which is to be deleted or ➭ Select Delete: all to delete the stored statistic data of all classes! After all classes are deleted, class A is set active and the error type of each class is set to First.
7 Operation with Barcode Reader 7.2 Configuring the Barcode Reader The barcode reader Z720A (as accessory) allows for all information available in barcode form to be quickly, easily and safely entered into the test reports. This type of data entry permits time-saving and low-cost acquisition of large amounts of information, e.g. for series measurements of devices provided with barcodes. The barcode reader Z720A is configured for the following barcodes: CODE 39 / CODE 128 / EAN13 (12 digits) * 7.
8 Data exchange with a PC Transmission of the data to the PC is only possible when the SI module is connected to the test instrument, which, in turn is connected to the mains. ➭ Connect the PC to the RS232 connection socket of the SI module via an interface cable. GMC-I Messtechnik GmbH 9 Error Message Message when the STORE key has been pressed although there is no free memory.
10 Technical Data Data Memory Connection elements Fasteners on test instrument 2 knurled screws for fastening in the lid of the test instrument; transmission of measured data and power supply via ribbon cable and 9-pin D-SUB connector, to be connected to the RS232 interface of the test instrument Interfaces RS232, bidirectional, 9-pin D-SUB socket, e.g. for connection to a PC or a barcode reader, or RFID Scanner USB, 4 pin USB1.
USB Interface The 9-pin D-SUB connector for connection of the SI module to the SECUTEST 0701S tester has the following pin assignment: 1: Enable remote control „Plus“ 2: RXD 3: TXD 4: NC 5: GROUND 6: Enable remote contr. "GROUND" 7: NC 8: NC 9: +9 V 1 3 2 6 7 4 8 Type Operating voltage 5 9 The 9-pin D-SUB connection socket for connection to PC, barcode reader, etc.
Electromagnetic Compatibility (EMC) Reference Conditions Operating voltage for connection to test instrument Ambient temperature Relative humidity 9 V 0.5 V DC or 8 V 0.5 V rectified +23 C 2 K 40 60 % Interference emission Interference immunity EN 61326-1:2013 class B EN 61326-1:2013 Mechanical Design Ambient Conditions Operating temperature Storage temperature Humidity 24 0 C ... +40 C 20 C ... +60 C max.
11 11.1 Maintenance 11.3 How to Reset the SI Module The instrument is a category 9 product (monitoring and control instrument) in accordance with ElektroG (German Electrical and Electronic Device Law). This device is subject to the RoHS directive. We identify our electrical and electronic devices in accordance with WEEE 2012/19/EU and ElektroG with the symbol shown to the right per DIN EN 50419. These devices may not be disposed with the trash.
12 Repair and Replacement Parts Service When you need service, please contact: GMC-I Service GmbH Service Center Thomas-Mann-Straße 20 90471 Nürnberg • Germany Phone +49 911 817718-0 Fax +49 911 817718-253 E-Mail service@gossenmetrawatt.com www.gmci-service.com This address is only valid in Germany. Please contact our representatives or subsidiaries for service in other countries.
