Owner manual

Upon receipt, thoroughly inspect for any
freight damage which should be brought to
the attention of the delivery carrier.
Compare the catalog description listed on
the packing slip with the label on the
carton to ensure that you have received
the correct merchandise.
NEW INSTALLATION FOR 10” AW and A
MICROGROOVE BAFFLE YOKE and
REFLECTOR
1. Insert yoke assembly through aperture of
recessed housing (see Figure 1).
2. Insert feet of yoke into raised slots
located on housing pan (see Figure 2).
3. Attach socket cup to top of reflector by
aligning and engaging springs in socket
cup with slots in top of reflector (see
Figure 3).
4. Pull end of yoke coil spring down through
aperture and attach it to screw located on
top of socket cup (see Figure 4). Tighten
screw. *CAUTION: Coil spring under tension.
When working with spring, use extreme
caution.
5. Grip reflector flange and allow coil spring
to retract, pulling reflector tight to ceiling.
*CAUTION: Coil spring under tension. When
working with spring, use extreme caution.
WALLWASH REFLECTORS- Make sure that the
wallwash component of the reflector is pro-
perly oriented with the wall to be illuminated
(see Figure 5).
6. Install lamp. DO NOT EXCEED INCANDE-
SCENT WATTAGE AS NOTED ON LABEL
LOCATED INSIDE REFLECTOR. FOR HID
LAMPS, REFER TO LABEL LOCATED BESIDE
SOCKET FOR PROPER LAMP TYPE AND
WATTAGE.
7. To remove the reflector: Remove lamp,
compress springs in socket cup and remove
socket cup from reflector.
Figure 1
SAVE THESE INSTRUCTIONS
Figure 3
Figure 4
Figure 2
Figure 5
Wall to be
Illuminated
Wallwash
Component
Springs
Top of
Reflector Slots
Raised Slots of
Housing Pan
Yoke Foot
Socket Cup
US
Socket
Cup
Feed Screw Through
Spring Keyhole
End of Yoke Coil
Spring
TRAHCGNITOOHSELBUORT
nimelborpehtetacol,noitidnocdoognimeesyehtfI.eludomni-emarfropmalehtotegamadelbis
ivynarofkcehC
.snoitcaevitcerrocdnasesuacelbissopfotsilgniwollofeht
motpmySesuaCelbissoPnoitcAevitcerroC
OTSLIAFPMAL
THGIL
dezigrenetonerutxifehtgnideeftiucriC·
noitcennocelud
omrotiucricnirorregniriW·
pmalytluaF·
tuptuotsallabroeniL·
tsallabytluaF·
wolooterutarepmettneibmA·
.dezig
renesitiucrictahterusneotesufrorekaerbtiucrickcehC·
erasnoitcennoctahterusneotxobecilpserutxifenimaxE·
.tcerroc
ylbareferp,pmalrehtonaetutitsbusdnapmalytluafehtevomeR·
lanigiroehtecalper,sthgilpmalehtfI.thg
ilotnwonksitahteno
.enowenahtiw
.egatlovtiucricnepokcehC.erutxiftaegatlovenilkcehC·
.ytiunitnoctiucrickc
ehC·
.snoitidnoclatnemnorivnegnitsixetsniagagnitartsallabkcehC·
TUOSEOGPMAL
GNITHGILRETFA
pmalytluaF· naht
rehtarmotpmyssihttibihxelliwpmalayllanoisaccO·
.pmalwenaetutitsbuS.thgilotgniliafylpmis
NOSELCYCPMAL
FFO
DNA
erutxifotesolcootsinoitalusnI·
hgihootegattawpmaL·
wolegatlovtuptuotsallaB·
)"3tsaelta(eludomdnuoramo
rfnoitalusnievomeR·
.gnisuohnideificepsegattawpmalllatsnI·
.egatlovtiucricnepokcehC.erutxifehttaegatlov
enilkcehC·
IMPORTANT SAFETY INFORMATION
For Your Protection, Read Carefully
- Risk of fire. Do not install insu-
lation within 3 inches of fixture sides or wir-
ing compartment, nor above the fixture in
such a manner as to entrap heat.
• Turn off the power supply.
• Ground the fixture to avoid potential
electrical shocks.
• Do not handle an energized fixture or
energize any fixture with wet hands,
when standing on a wet or damp sur-
face, or in water.
• Double check all electrical connections
to be sure they are tight and correct.
• Match wattage of fixture and lamp ex-
actly.
• Do not remove or insert lamp when power
is on.
• Do not scratch glass or subject lamp to
undue pressure as either may cause
lamp breakage.
• Protect operating lamp from sources
of moisture.
INSTALLATION INSTRUCTIONS
10” AW
and
Microgroove Baffle Yoke
and Reflector
Part No. CJ520349 Rev. B
©2007 Gotham 4/07