Installation, Operation, and Maintenance Manual 3298 Family
Table of Contents Table of Contents Introduction and Safety .......................................................................................................... Introduction ............................................................................................................................. Safety ...................................................................................................................................... Safety terminology and symbols ................................
Table of Contents Bearing lubrication ................................................................................................................ Lubricating oil requirements ............................................................................................... Acceptable oil for lubricating bearings ................................................................................ Lubricate the bearings with oil ..................................................................................
Table of Contents Local ITT Contacts .............................................................................................................. 116 Regional offices ..................................................................................................................
Introduction and Safety Introduction and Safety Introduction Purpose of this manual The purpose of this manual is to provide necessary information for: • Installation • Operation • Maintenance CAUTION: Read this manual carefully before installing and using the product. Improper use of the product can cause personal injury and damage to property, and may void the warranty. NOTICE: Save this manual for future reference, and keep it readily available at the location of the unit.
Introduction and Safety Safety terminology and symbols About safety messages It is extremely important that you read, understand, and follow the safety messages and regulations carefully before handling the product.
Introduction and Safety Waste and emissions regulations Observe these safety regulations regarding waste and emissions: • Appropriately dispose of all waste. • Handle and dispose of the processed liquid in compliance with applicable environmental regulations. • Clean up all spills in accordance with safety and environmental procedures. • Report all environmental emissions to the appropriate authorities.
Introduction and Safety Magnetic precautions WARNING: Magnetic drive pumps contain very strong magnets that can pose health risks.
Introduction and Safety • Intrinsically safe circuits are normally required for the automatic level-control system by the level regulator if mounted in zone 0. • The yield stress of fasteners must be in accordance with the approval drawing and the product specification. • Do not modify the equipment without approval from an authorized ITT representative. • Only use parts that are provided by an authorized ITT representative.
Introduction and Safety • Normal wear and tear ITT assumes no liability for these situations: • Bodily injuries • Material damages • Economic losses Warranty claim ITT products are high-quality products with expected reliable operation and long life. However, should the need arise for a warranty claim, then contact your ITT representative.
Transportation and Storage Transportation and Storage Inspect the delivery Inspect the package 1. Inspect the package for damaged or missing items upon delivery. 2. Note any damaged or missing items on the receipt and freight bill. 3. File a claim with the shipping company if anything is out of order. If the product has been picked up at a distributor, make a claim directly to the distributor. Inspect the unit 1. Remove packing materials from the product.
Transportation and Storage Table 1: Methods Pump type A bare pump without lifting handles A base-mounted pump Lifting method Use a suitable sling attached properly to solid points like the casing, the flanges, or the frames. Use slings under the pump casing and the drive unit, or under the base rails.
Transportation and Storage Figure 3: Proper lifting method for a vertical pump with a driver Figure 4: Proper lifting method for a vertical pump with no driver Figure 5: Example of a proper lifting method 12 3298 Family Installation, Operation, and Maintenance Manual
Transportation and Storage Figure 6: Example of a proper lifting method Storage guidelines Pump storage requirements Storage requirements depend on the amount of time that you store the unit. The normal packaging is designed only to protect the unit during shipping. Length of time in storage Upon receipt/short-term (less than six months) Long-term (more than six months) Storage requirements • Store in a covered and dry location. • Store the unit free from dirt and vibrations.
Product Description Product Description General description Model 3298 Model 3298 is a sealless, close-coupled or frame-mounted, centrifugal pump with an enclosed impeller that is driven by a synchronous magnetic coupling. All sizes of the 3298 meet the dimensional standards of ANSI B73.1 except for 1x1.5-5 and the 1.5x2-6. Model SP3298 SP3298 is a self-priming, sealless, close-coupled or frame-mounted, centrifugal pump with an enclosed impeller that is driven by a synchronous magnetic coupling.
Product Description Bearings The standard material for radial bearings and thrust bearings is carbon. Pure Sintered Alpha Grade Silicon Carbide or DryGuard™ Pure Sintered Alpha Grade Silicon Carbide are optional. Standard close-coupled mounting The drive magnet assembly is keyed, setscrewed, and mounted directly to the motor shaft. This arrangement eliminates the need to perform pump-to-motor alignment.
Product Description Nameplate field MAX. DIA. GPM FT HD RPM MOD. SIZE STD. NO. MAT L. CONST. SER. NO.
Product Description Nameplate field 2 G/D T4 Explanation Category 2 Pump can be used when gas and dust are present Temperature class Table 5: Temperature class definitions Code Maximum permissible surface temperature in °F (°C) T1 842 (450) T2 572 (300) T3 392 (200) T4 275 (135) T5 212 (100) T6 185 (85) Minimum permissible surface temperature in °F (°C) 700 (372) 530 (277) 350 (177) 235 (113) Option not available Option not available NOTICE: Make sure that the code classifications on the pump are compat
Installation Installation Preinstallation Precautions WARNING: • When installing in a potentially explosive environment, make sure that the motor is properly certified. • You must earth (ground) all electrical equipment. This applies to the pump equipment, the driver, and any monitoring equipment. Test the earth (ground) lead to verify that it is connected correctly. • Electrical Connections must be made by certified electricians in compliance with all international, national, state, and local rules.
Installation Foundation requirements Precautions CAUTION: If your pump is a Model NM3171, NM3196, 3198, 3298, V3298, SP3298, 4150, 4550, or 3107 there is a possible risk of static electric discharge from plastic parts that are not properly grounded. If the pumped fluid is non-conductive, drain and flush the pump with a conductive fluid under conditions that will not allow for a spark to be released to the atmosphere.
Installation Baseplate-mounting procedures Prepare the baseplate for mounting 1. Remove all the attached equipment from the baseplate. 2. Clean the underside of the baseplate completely. 3. If applicable, coat the underside of the baseplate with an epoxy primer. Use an epoxy primer only if you used an epoxy-based grout. 4. Remove the rust-proofing coat from the machined mounting pads using an appropriate solvent. 5. Remove water and debris from the foundation-bolt holes.
Installation NOTICE: Remove all dirt from the mounting pads in order to make sure that you achieve the correct leveling. Failure to do so can result in equipment damage or decreased performance. 6. Level the baseplate both lengthwise and across by adding or removing shims or moving the wedges. These are the leveling tolerances: • A maximum difference of 0.125 in. (3.2 mm) lengthwise • A maximum difference of 0.059 in. (1.5 mm) across You can use the baseplate-leveling worksheet when you take the readings.
Installation NOTICE: Remove all dirt from the mounting pads in order to make sure that you achieve the correct leveling. Failure to do so can result in equipment damage or decreased performance. a) Put one machinist's level lengthwise on one of the two pads. b) Put the other machinist's level across the ends of the two pads. c) Level the pads by adjusting the four jackscrews in the corners. Make sure that the machinist's level readings are as close to zero as possible, both lengthwise and across.
Installation 7. Check that the driver's mounting pads are level and adjust the jackscrews and the foundation bolts if necessary. The correct level measurement is a maximum of 0.002 in./ft (0.0167 mm/m). The maximum variation from one side of the baseplate to the other is 0.015 in. (0.38 mm).
Installation Baseplate-leveling worksheet 24 3298 Family Installation, Operation, and Maintenance Manual
Installation Pump-to-driver alignment Precautions WARNING: • Follow shaft alignment procedures in order to prevent catastrophic failure of drive components or unintended contact of rotating parts. Follow the coupling installation and operation procedures from the coupling manufacturer. • Always disconnect and lock out power to the driver before you perform any installation or maintenance tasks. Failure to disconnect and lock out driver power will result in serious physical injury.
Installation Final alignment (hot alignment) checks When After the first run Periodically Why This ensures correct alignment when both the pump and the driver are at operating temperature. This follows the plant operating procedures. Permitted indicator values for alignment checks NOTICE: The specified permitted reading values are valid only at operating temperature. For cold settings, other values are permitted. You must use the correct tolerances.
Installation 2. Rotate the pump coupling half (X) in order to check that the indicators are in contact with the driver coupling half (Y) but do not bottom out. 3. Adjust the indicators if necessary. Pump-to-driver alignment instructions Perform angular alignment for a vertical correction 1. Set the angular alignment indicator to zero at the top-center position (12 o’clock) of the driver coupling half (Y). 2. Rotate the indicator to the bottom-center position (6 o’clock). 3. Record the indicator reading.
Installation When the reading value is... Then... Figure 10: Top view of an incorrect horizontal alignment 4. Repeat the previous steps until the permitted reading value is achieved. Maximum permitted value for angular alignment: • 0.002 in. (0.
Installation Table 6: Cold settings for parallel vertical alignment If the operating temperature of the pumped Then, set the driver shaft parallel vertical liquid is... alignment... 50°F (10°C) 0.002 in. (0.05 mm) lower 150°F (65°C) 0.001 in. (0.03 mm) higher 250°F (120°C) 0.005 in. (0.12 mm) higher Perform parallel alignment for a horizontal correction A unit is in parallel alignment when the parallel indicator (P) does not vary by more than 0.002 in. (0.
Installation Perform complete alignment for a horizontal correction A unit is in complete alignment when both the angular indicator (A) and the parallel indicator (P) do not vary by more than 0.002 in. (0.05 mm) as measured at four points 90° apart. 1. Set the angular and parallel dial indicators to zero at the left side of the driver coupling half (Y), 90° from the top-center position (9 o’clock). 2.
Installation 6. Fill the remainder of the baseplate with grout, and allow the grout to set for at least 48 hours. 1. 2. 3. 4. 5. Baseplate Grout Foundation Dam Bolt 7. Tighten the foundation bolts. 8. Recheck the alignment. Piping checklists Fastening WARNING: • Only use fasteners of the proper size and material. • Replace all corroded fasteners. • Make sure that all fasteners are properly tightened and that there are no missing fasteners.
Installation Piping guidelines Guidelines for piping are given in the Hydraulic Institute Standards available from the Hydraulic Institute at 9 Sylvan Way, Parsippany, NJ 07054-3802. You must review this document before you install the pump. Checklist Check Check that all piping is supported independently of, and lined up naturally with, the pump flange. See Alignment criteria for pump flanges.
Installation Example: Installation for expansion Correct 1. Incorrect Expansion loop/joint Suction-piping checklist Performance curve reference CAUTION: Vary the capacity with the regulating valve in the discharge line. Never throttle the flow from the suction side. This action can result in decreased performance, unexpected heat generation, and equipment damage.
Installation Check When suction strainers or suction bells are used, check that they are at least three times the area of the suction piping. Explanation/comment Checked Suction strainers help to prevent clogging. Mesh holes with a minimum diameter of 1/16 in. (1.6 mm) are recommended. If more than one pump operates This recommendation helps you from the same liquid source, to achieve a higher pump perforcheck that separate suction-piping mance. lines are used for each pump.
Installation Example: Elbow close to the pump suction inlet Correct Incorrect The correct distance between the inlet flange of the pump and the closest elbow is at least two pipe diameters. 1. 2. Enough distance to prevent cavitation Eccentric reducer with a level top Example: Suction piping equipment Correct 1. 2. 3. 4. 5. Incorrect Suction pipe sloping upwards from liquid source 1.
Installation Check If increasers are used, check that they are installed between the pump and the check valve. If quick-closing valves are installed in the system, check that cushioning devices are used. Explanation/comment See Example: Discharge piping equipment for illustrations. Checked This protects the pump from surges and water hammer. Example: Discharge piping equipment Correct Incorrect 1. 2. 3. 4. 1. 2.
Commissioning, Startup, Operation, and Shutdown Commissioning, Startup, Operation, and Shutdown Preparation for startup DANGER: Avoid death or serious injury. Explosion and/or seizure of pump can cause fire and/or burns. Never operate pump past the pressure and temperature limits shown on the nameplate on the pump. WARNING: • Failure to follow these precautions before you start the unit will lead to serious personal injury and equipment failure.
Commissioning, Startup, Operation, and Shutdown • Run a new or rebuilt pump at a speed that provides enough flow to flush and cool the close-running surfaces of the stuffing-box bushing. • If temperatures of the pumped fluid will exceed 200°F (93°C), then warm up the pump prior to operation. Circulate a small amount of fluid through the pump until the casing temperature is within 100°F (38°C) of the fluid temperature.
Commissioning, Startup, Operation, and Shutdown b) Lift upwards. 1. Annular groove 2. Driver half of the coupling guard 3. Driver 6. Remove the remaining nut, bolt, and washers from the pump half of the coupling guard. It is not necessary to remove the end plate from the pump side of the bearing housing. You can access the bearing-housing tap bolts without removing this end plate if maintenance of internal pump parts is necessary. 7.
Commissioning, Startup, Operation, and Shutdown Check the rotation - Frame Mounted WARNING: • Operating the pump in reverse rotation can result in the contact of metal parts, heat generation, and breach of containment. • Always disconnect and lock out power to the driver before you perform any installation or maintenance tasks. Failure to disconnect and lock out driver power will result in serious physical injury.
Commissioning, Startup, Operation, and Shutdown Refer to driver/coupling/gear manufacturers IOM for specific instructions and recommendations. Install the coupling guard WARNING: • Never operate a pump without a properly installed coupling guard. Personal injury will occur if you run the pump without a coupling guard. • Electrical Connections must be made by certified electricians in compliance with all international, national, state, and local rules.
Commissioning, Startup, Operation, and Shutdown If the pump size is... 1. 2. 3. 4. Then... Driver Pump end plate Bearing housing Jam nut 3. Put the pump-half of the coupling guard in place: a) Slightly spread the bottom apart. b) Place the coupling guard half over the pump-side end plate. 1. 2. 3. 4. Annular groove Pump-side end plate Driver Pump half of the coupling guard The annular groove in the coupling guard half must fit around the end plate.
Commissioning, Startup, Operation, and Shutdown 1. Annular groove 2. End plate (pump end) 3. Guard half 4. Use a bolt, a nut, and two washers to secure the coupling guard half to the end plate. Tighten securely. 1. Nut 2. Washer 3. Bolt 5. Put the driver half of the coupling guard in place: a) Slightly spread the bottom apart.
Commissioning, Startup, Operation, and Shutdown b) Place the driver half of the coupling guard over the pump half of the coupling guard. The annular groove in the coupling guard half must face the motor. 1. Annular groove 2. Driver half of the coupling guard 3. Driver 6. Place the driver-side end plate over the motor shaft. 7. Place the driver-side end plate in the annular groove of the driver-half of the coupling guard. 8.
Commissioning, Startup, Operation, and Shutdown 9. Slide the driver-half of the coupling guard towards the motor so that the coupling guard completely covers the shafts and coupling. 10. Use a nut, a bolt, and two washers to secure the coupling guard halves together. 11. Tighten all nuts on the guard assembly. WARNING: Never operate the pump without the coupling guard correctly installed. Bearing lubrication WARNING: Pumps are shipped without oil.
Commissioning, Startup, Operation, and Shutdown Lubricating oil requirements ISO grade Approximate SSU at 100°F (38°C) DIN 51517 Kinematic viscosity at 105°F (40°C) mm2/sec Bearing temperature below 180°F (82°C) ISO viscosity grade 68 300 Bearing temperature above 180°F (82°C) ISO viscosity grade 100 470 C68 68 C100 100 Acceptable oil for lubricating bearings Acceptable lubricants Brand Chevron Exxon Mobil Philips Shell Gulf Lubricant type GTS Oil 68 NUTHO H68 DTE 26 300 SSU @ 100°F (38°C)
Commissioning, Startup, Operation, and Shutdown 1. Discharge isolation valve 2. Check valve 3. Suction isolation valve Prime the pump with the suction supply below the pump Use a foot valve and an outside source of liquid in order to prime the pump. The liquid can come from one of these sources: • A priming pump • A pressurized discharge line • Another outside supply 1. Close the discharge isolation valve. 2. Open the air vent valves in the casing. 3.
Commissioning, Startup, Operation, and Shutdown This illustration is an example of priming the pump with a foot valve using a bypass around the check valve: 1. 2. 3. 4. 5. By-pass line Shutoff valve Foot valve Check valve Discharge isolation valve Other methods of priming the pump You can also use these methods in order to prime the pump: • Prime by ejector • Prime by automatic priming pump Start the pump WARNING:Immediately observe the pressure gauges.
Commissioning, Startup, Operation, and Shutdown CAUTION: • Immediately observe the pressure gauges. If discharge pressure is not quickly attained, stop the driver, reprime, and attempt to restart the pump. • Observe the pump for vibration levels, bearing temperature, and excessive noise. If normal levels are exceeded, shut down the pump and resolve the issue. • On pure or purge-oil mist-lubricated units, remove the viewing port plugs to verify that oil mist flowing properly. Replace the plugs.
Commissioning, Startup, Operation, and Shutdown Group 3600 S V3298 S M 1. 2. 3. 4. 5. Pump size 60 Hertz GPM 1800 1200 1 x 1½ - 6 5 2x3-6 30 3000 3 15 1½ x 2 - 6 1½ 2 - 8 2x3-6 1½ x 2 - 10 3 30 30 5 5 60 60 30 1500 2 8 50 Hertz m3/hr 1000 2 6 1 3 0.5 1 2 20 20 3 2 11 11 5 1 7 7 0.7 0.5 4 4 0.5 All flows are for a continuous operation of 24 hours a day, seven days a week. These values are based on water with a specific gravity of 1.0 and specific heat of 1.0.
Commissioning, Startup, Operation, and Shutdown CAUTION: • The pump and system must be free of foreign objects. If pump becomes plugged, shut down and unplug prior to restarting pump. • Avoid excessive vibration levels. Excessive vibration levels can damage the bearings, stuffing box or seal chamber, and the mechanical seal, which can result in decreased performance. • Avoid increased radial load. Failure to do so can cause stress on the shaft and bearings. • Avoid heat build-up.
Commissioning, Startup, Operation, and Shutdown 4. Check the alignment while the unit is still hot. See Pump-to-driver alignment in the Installation chapter. 5. Reinstall the coupling guard. 6. Restart the pump and driver.
Maintenance Maintenance Maintenance schedule Maintenance inspections A maintenance schedule includes these types of inspections: • Routine maintenance • Routine inspections • Three-month inspections • Annual inspections Shorten the inspection intervals appropriately if the pumped fluid is abrasive or corrosive or if the environment is classified as potentially explosive. Routine maintenance Perform these tasks whenever you perform routine maintenance: • Lubricate the bearings. • Inspect the seal.
Maintenance Required tools WARNING: This pump contains extremely strong magnets. You must use non-magnetic tools and work surfaces. Non-magnetic tools • 9/16-inch and 3/4-inch socket wrench • Non-metallic hammer Tools • • • • • • • • Long T-handle hex wrench in size 3/16-inch 1/2-inch, 9/16-inch, and 3/4-inch sockets Socket wrench with a minimum extension of 4 in.
Maintenance Disassembly Disassembly precautions WARNING: • Chemical hazard. You must individually decontaminate each component according to all federal, state, local, and company environmental regulations. • A build up of gases within the pump, sealing system, or process-piping system can result in an explosive environment within the pump. Make sure that the process piping system, pump, and sealing system are properly vented prior to operation. • Burn Hazard. Coupling may be hot.
Maintenance b) Collect the flushed liquid as it drains out of the drain connection. c) Flush the pump in order to remove residue. Disassemble the close-coupled pump 1. For all pumps except the V group, secure the C-face motor support and bearing frame (228) to the workbench. 2. Remove the four bolts (370B) from the C-face motor support and bearing frame (228).
Maintenance 3. For the M and L group pumps, tighten the jacking screws (418) until the gap between the clamp ring (141C) and the C-face motor support and bearing frame is 3.50 in. (8.89 cm). 4. For all pumps except the V group, grasp the suction flange of the casing and pull the casing-liquid end free from the magnet assembly. 5. For all pumps except the SP group, remove the casing bolts (356A). 6. Wrap a piece of emery cloth around the containment shell (750) and secure it with a large hose clamp.
Maintenance 8. For all groups except the SP, remove the impeller assembly (101). Figure 22: XS, S, M, and L groups Figure 23: V group 9. Remove the shaft (122A) if replacement is necessary. 10. Inspect and replace the bearings, if necessary: a) Inspect the bearing spider (101A). Press it out through the suction of the casing (100) if replacement is necessary. b) Use a bearing tool to press out the radial bearing (197B) from the impeller assembly (101), if replacement is necessary.
Maintenance 11. Inspect and replace these parts as necessary: Pump group M and L L S, M, and SP, and V Step Inspect the rear impeller wear ring (203) and remove it if replacement is necessary. Remove the retaining ring (361H). Then slide or press the magnet assembly (740A) off the impeller assembly (101). Figure 26: L group Remove the reverse thrust bearing (197C) from the containment shell (750) if replacement is necessary. 12.
Maintenance . Figure 28: Magnet assembly 3. Tighten the jacking screws evenly and in sequence until you can remove the magnet assembly (740B). 4. Remove the magnet assembly (740B) and place it away from any attracting metals. Figure 29: Magnet assembly removal 5. For the L and M group pumps, remove the 5/16 in. wear ring capscrew (372Y) and the wear ring from the bottom of the bearing frame (228).
Maintenance 6. Remove the bearing end-cover bolts (370C). Figure 31: Bearing end-cover bolt removal 7. Install two bearing end-cover bolts (370C) in the jacking screw holes and tighten them evenly in order to remove the bearing end cover (109A). 8. Slide the bearing end cover (109A) backwards. The labyrinth oil seal (332A) slides back with the end cover. 9. Remove the labyrinth seal (332A) and the bearing end cover (109A). 10. Remove and discard the gasket (360A). 11.
Maintenance 13. Remove the lip seal (333D). Figure 34: Lip seal removal Preassembly inspections Inspect pump parts according to the following criteria before reassembly in order to make sure the pump will run properly. Replace any part that does not meet the required criteria. Casing Inspect the casing for excessive wear, abrasive damage, cuts, or a loose liner. Spider bearing Inspect the spider bearing for cracks, chips, or scoring.
Maintenance Size 1½ x 3-10 2 x 3-10 3 x 4-10H 3 x 4-10G 4 x 6-10 New clearance inches (millimeters) 0.060 - 0.070 (1.52 - 1.78) Replace at inches (millimeters) 0.094 (2.4) Radial bearing • Inspect the bearings for cracks or chips. • Inspect the diametric bearing clearances: Shaft to bearing New clearance in inches (millimeters) 0.003 - 0.006 (0.076 - 0.152) Replace at inches (millimeters) 0.012 (0.305) Reverse and impeller thrust bearings Inspect these bearings for cracks, chips, or scoring.
Maintenance • Replace the magnet assembly if it was exposed to pumped fluid. • Inspect magnets for proper bonding to the carrier. Bearing frame - frame-mounted version only • Inspect the frame and frame foot for cracks. • Inspect the frame and rub ring for corrosion or pitting if parts have been exposed to pumped fluid. • Inspect the bearing frame bores. The maximum acceptable bore is: • S group: 2.4419 in. (62.024 mm) • M and L groups: 2.8353 in. (72.
Maintenance NOTICE: • Use caution when you use an hydraulic press because you cannot feel when the bearing hits the bottom of the bore. • Do not hammer the magnet assembly onto the shaft. This will damage the ball bearings. • Pressing the radial bearings into the impeller can cause some ETFE to peel. If this occurs, press out the bearings, remove any ETFE filings, and then press the bearings back into the impeller. • There are several methods you can use to install bearings.
Maintenance b) Use a center punch to stake the impeller at the end of the key in order to hold the key in place. Figure 37: 3298 S, M, and L groups, SP3298, and V3298 3. Install the radial bearing into the impeller: a) Lubricate the outside of the radial bearing. b) Use the bearing installation tool to press the radial bearing (197B) into the impeller. c) Support the impeller with the bearing press support tool. d) Line up the keyway in the bearing with the key in the impeller.
Maintenance 4. For all groups except XS, slide the bearing spacer (157A) into the impeller and then press the second radial bearing (197B) into the impeller. Figure 40: L group Figure 39: 3298 S and M groups, SP3298, and V3298 5. For the L group, press the impeller wear ring (203) into the impeller assembly. 6. Turn the impeller over and install the impeller thrust bearing (197D). Make sure to align the two slots in the impeller thrust bearing with the two tabs in the impeller.
Maintenance The lubricant is used to help the O-ring remain in place. Figure 43: XS group Figure 44: 3298, SP3298, and V3298 S, M, and L groups 10. For the SP3298, complete these steps: a) Place the backplate (444) face down on the work surface. b) Place the containment shell with the reverse thrust bearing in the backplate. c) Place a clamp ring (141C) over the containment shell and secure with clamp ring bolts (356A). d) Coat the O-ring (412V) with an O-ring lubricant.
Maintenance 11. Slide the impeller assembly (101) onto the shaft. Figure 46: 3298 XS, S, M, and L groups, and V3298 Figure 47: SP group 12. Press the spider (101A) into the volute insert (100U) with the spider tool. Then press the volute insert with the spider into the casing (100).
Maintenance Figure 50: SP3298 13. Check the total travel of the rotary assembly: Pump group 3298 XS 3298 S, V3298 S, and SP3298 3298 M and L, and V3298 M Travel between A and B in inches (millimeters) 0.026 - 0.083 in. (0.66 - 2.11 mm) 0.013 - 0.100 in. (0.33 - 2.5 mm) 0.020 - 0.105 in. (0.51 - 2.
Maintenance Figure 54: V3298 Figure 53: SP3298 14. For the 3298 and V3298, install these items into the casing: a) Install the containment shell and impeller assembly into the casing (100). Use care that the O-ring (412M) remains in place. b) Install the clamp ring (141C) into the casing (100) with the hex capscrews (356A).
Maintenance 15. Install the impeller assembly and backplate/clamp ring/containment shell assembly into the casing (100) using casing bolts (372V). Make sure that the O-ring remains in place. Figure 57: SP3298 16. Set the partially-built assembly aside and away from any attracting metals. Continue the assembly with the close coupled or frame mounted version of assembly as described in this chapter. Reassemble the close-coupled pump 1.
Maintenance 5. Slowly drop in the magnet assembly until the shim rests on the face of the C-face motor support. Figure 60: Drive magnet assembly Figure 61: XS and S group installation dimensions Figure 62: M and L group installation dimensions 6. Rotate the magnet assembly (740B) to line up the key (178Y) with the access hole on the C-face motor support (228). 7. Tighten the first setscrew (222L) through the access hole. 8.
Maintenance 3. Bolt or clamp the bearing frame (228) to the work bench. Figure 64: Bearing frame secured to bench 4. Install the shaft (122B) with ball bearings (112) into the bearing frame (228). Point the threaded end of the shaft towards the magnets. Figure 65: S group bearing installation 5. For the M and L group, install the wave washer.
Maintenance 6. Install the bearing-end cover gasket (360A) and bearing end cover (109A) with hex capscrews (370C). Figure 67: Bearing frame assembly 7. Press the labyrinth seal (332A) into the end cover (109A): a) Make sure that the O-rings are in grooves of labyrinth seal. b) Orient the expulsion ports to the 6 o’clock position and press the seal into the bearing end cover (109A) until it is shouldered against the end cover. No adjustment is necessary. 8. Install the key (178Y) on the shaft (122B).
Maintenance d) For the M and L groups, install a 5 /16 in. hex capscrew (372Y) into the bottom of the frame (228). This capscrew prevents the rub ring (144A) from rotating during pump operation. Figure 69: M and L group drive magnet assembly Complete the reassembly (close-coupled and frame-mounted pumps) 1. For all groups except XS, install the gasket (360W) into the clamp ring (141C). 2. Bolt the C-face support and frame (228) to the work bench. 3.
Maintenance b) Install the two guide rods (B03189A) into the clamp ring (141C). These rods help you guide the casing assembly into the C-face support and frame (228), which contains the drive magnets (740B). 1. Casing assembly 2. Guide rods Figure 71: Casing assembly with guide rods 4. Slide the casing assembly into the C-face support and bearing frame assembly: If your pump group is... XS or S Then... 1. 2. M or L 1. 2. 1. 2.
Maintenance Location Cover-to-frame – 370C Drain screws – 426A XS and S Drain screws – 426A M and L Dry threads torque in ft-lbs (Nm) 30 (40) 14 (19) 18 (25) Impeller trimming guidelines Precautions • Do not chuck the impeller assembly. • Do not make cuts that are larger than 0.050 in. (0.127 cm) • Do not over-tighten the arbor screw because this can crack the carbon bearings.
Maintenance • Tighten the screw only enough to turn the impeller without it slipping. • The allowed front shroud TIR is 0.060 in. (0.152 cm) • For the XS impeller, trim both the front and back shrouds and the vanes to a minimum diameter of 3.75 in. (9.53 cm). • When you trim between 3.00 in. (7.62 cm) and 3.75 in. (9.53 cm), trim only the front shroud and the vanes. Trimming examples 1. 2. 3. 4. Impeller Steel washer with rubber bond Paper gasket Arbor Figure 73: XS group 1. 2. 3. 4. 5.
Maintenance 1. 2. 3. 4. 5. Steel washer with rubber bond Socket head capscrew Impeller Paper gasket Arbor Figure 75: L group SP3298 volute insert trimming guidelines Trimming guidelines Do not make cuts larger than 0.050 in (0.127 cm) Use arbor tool C06820A for SP3298 size 1x1.5-6 and C06821A for SP3298 size 2x3-6. Make sure that the arbor runs within 0.002 in. (0.005 cm) TIR. 1. Volute insert 2.
Maintenance Impeller diameter in inches (centimeters) 5.25 (13.34) 5.38 (13.67) 5.50 (13.97) 5.62 (14.27) 5.75 (14.61) 5.88 (14.94) 6.00 (15.24) 6.06 (15.39) 1. 2. 3. 4. 5. "R" +/- 0.010 inches (0.25 mm) 2.688 (6.827) 2.750 (6.985) 2.813 (7.145) 2.875 (7.303) 2.938 (7.463) 3.000 (7.620) 3.063 (7.780) 3.094 (7.
Maintenance Part Impeller bearing Radial bearing Part number 178S 197B Reverse thrust bearing Impeller thrust bearing 197C 197D Rear impeller wear ring (M and 203 L groups) Material Tefzel Standard – carbon Optional – silicon carbide Optional – DryGuard silicon carbide Carbon-filled Teflon Standard – carbon filled Teflon Optional – silicon carbide Optional – DryGuard silicon carbide Standard – carbon filled Teflon Quantity 1 2 Material Varnished Kraft Carbon filled Teflon Steel Buna rubber Steel Stan
Troubleshooting Troubleshooting Operation troubleshooting Symptom The pump is not delivering liquid. Cause The pump is not primed. The suction line is clogged. The impeller is clogged. The magnet is de-coupling. The suction line is clogged. The impeller is clogged. The magnet is de-coupling. The pump is not producing rated flow or head. Pump starts and then stops pumping. The bearings run hot. Pump is noisy or vibrates.
Troubleshooting Symptom The motor requires excessive power. The condition monitoring device shuts down the pump. Cause The head is lower than the rating and the pump has too much liquid. The liquid is heavier than expected. The head is higher than the rating, which is at capacity. The rotating parts are binding or are severely worn. The motor rotation is incorrect. The sleeve and thrust bearings are damaged. There is a plugged recirculation circuit. There is recirculation liquid vaporization.
Troubleshooting 1. Check to see if the plastic that surrounds the outboard thrust bearing is melted. 2. Check to see if the plastic that surrounds the carbon or silicon carbide impeller radial bearings is melted. 3. Check to see if the plastic that surrounds the inboard thrust bearings is melted. 4. If the impeller seizes on the shaft due to excessive heat, the shaft can spin in the shaft spider, which wears the inside diameter of the shaft spider.
Parts Listings and Cross-Sectionals Parts Listings and Cross-Sectionals 3298 XS group close-coupled pump in sizes 1 x 1-1/2 - 5 and 1-1/2 x 2-6 With NEMA motor 86 3298 Family Installation, Operation, and Maintenance Manual
Parts Listings and Cross-Sectionals With IEC motor Parts list Item 100 101 101A1 Part name Casing Impeller assembly Bearing spider 122A Stationary shaft 141C 178Y 197B1 Clamp ring Key – motor to magnet assembly Bearing – radial 197D1 Bearing – impeller thrust 222L 228 2412 351G 356A 358 370B Setscrew C-face motor support Frame foot Gasket – casing drain Hex capscrew – clamp ring to casing Cover – drain Hex capscrew – support to clamp ring 3298 Family Installation, Operation, and Maintenance Manu
Parts Listings and Cross-Sectionals Item 412M1 Part name O-ring – containment shell 426A 492A 740B Hex capscrew – drain cover Plug – access hole Drive carrier 750 Containment shell Material Standard: Viton Optional: EPDM Optional: Teflon – encapsulated Viton Optional: Chemraz 505 Optional: Kalrez 4079 304 SS Steel Carbon-filled Tefzel / fiber-reinforced vinylester Carbon-filled Tefzel / Fiber-reinforced Vinylester 1 Recommended spare parts Not supplied on size 1.
Parts Listings and Cross-Sectionals Item 122A Part name Stationary shaft 122B 141C 157A 178S1 178Y 197B1 Drive shaft Clamp ring Bearing spacer – radial bearings Key – impeller to radial bearings Key – drive carrier Bearing – radial 197C1 197D1 Bearing – reverse thrust Bearing – impeller thrust 228 332A1 333D1 351G1 355A1 356A 358 360A1 360W 370B 370C 412M1 Frame – bearing Labyrinth seal – outboard Oil lip seal – inboard Gasket – casing drain Hex nut Hex capscrew – clamp ring to casing Flange – casing
Parts Listings and Cross-Sectionals 3298 S group close-coupled pump in sizes 1 x 1-1/2 - 6, 1 x 1-1/2 - 8, 1-1/2 x 3-7, and 2 x 3-6 With NEMA motor 90 3298 Family Installation, Operation, and Maintenance Manual
Parts Listings and Cross-Sectionals With IEC motor S group close-coupled parts list Item 100 101 101A1 Part name Casing Impeller assembly Bearing spider 122A Stationary shaft 141C 157A 178S1 178Y 197B1 Clamp ring Bearing spacer – radial bearings Key – impeller to radial bearings Key – motor to carrier Bearing – radial 197C1 197D1 Bearing – reverse thrust Bearing – impeller thrust 222L 228 351G1 356A 358 360W1 370B Setscrew Motor support – close coupled Gasket – casing drain Hex capscrew – clamp r
Parts Listings and Cross-Sectionals Item 412M1 Part name O-ring – containment shell 426A 492A 740B 750 1 Recommended spare parts Hex capscrew – casing drain Access hole plug Drive magnet assembly Containment shell Material Standard: Viton Optional: EPDM Optional: Teflon-encapsulated Viton Optional: Chemraz 505 Optional: Kalrez 4079 304 SS Steel Cast iron / neodymium iron Tefzel / fiber-reinforced vinylester Item 228 333L 371 388T 408A 492A 503 742B 1 Used with motor frame 132 and 160 only.
Parts Listings and Cross-Sectionals 3298 M group frame-mounted pump in sizes 3 x 4 - 7, 1-1/2 x 3 - 8, 2 x 3 - 8, 1 x 2 - 10 M group frame-mounted drawing M group frame-mounted parts list Item 100 101 101A1 Part name Casing Impeller assembly Bearing spider 109A 1121 113A 122A End cover Ball bearings Plug, oil fill Stationary shaft 122B 141C 144A 157A 178S1 178Y Drive shaft Clamp ring Rub ring Bearing spacer – radial Key – impeller to bearings Key – drive carrier 3298 Family Installation, Operation,
Parts Listings and Cross-Sectionals Item 197B1 Part name Bearing – radial 197C1 197D1 Bearing – reverse thrust Bearing – impeller thrust 2031 228 241 319 332A 333D1 351G1 355A 356A 358 360A1 360W1 370B 370C 370F 372Y 408A 408J 412M1 Wear ring – rear impeller Frame – bearing Frame foot Sight window Labyrinth seal Lip seal Gasket – casing drain Flanged hex nut Hex capscrew – clamp ring to casing Flange – casing drain Gasket – end cover to frame Gasket – frame to clamp ring Hex capscrew – frame to clamp r
Parts Listings and Cross-Sectionals 3298 M group close-coupled pump in sizes 3 x 4 - 7, 1-1/2 x 3 - 8, 2 x 3 - 8, 1 x 2 - 10 M group close-coupled drawing M group close-coupled parts list Item 100 101 101A1 Part name Casing Impeller assembly Bearing spider 122A Stationary shaft 141C 157A 178S1 178Y 197B1 Clamp ring Bearing spacer – radial Key – impeller to bearings Key – motor to carrier Bearing – radial 197C1 197D1 Bearing – reverse thrust Bearing – impeller thrust 2031 222L 228 Wear ring – rear
Parts Listings and Cross-Sectionals Item 351G1 356A 358 360W1 370B 370F 371 408A 412M1 Part name Gasket – casing drain Hex capscrew – clamp ring to casing Flange – casing drain Gasket – frame support to clamp ring Hex capscrew – frame to clamp ring Hex capscrew – frame foot Hex capscrew – frame to motor Plug – drain O-ring – containment shell 418 426A 492A 740B 750 1 Recommended spare parts Hex tap bolt – jacking Hex capscrew – casing drain Plug – access hole Drive carrier Containment shell Material Gyl
Parts Listings and Cross-Sectionals Figure 77: Two-piece impeller L group frame-mounted parts list Item 100 101 101A1 Part name Casing Impeller assembly Bearing spider 109A 1121 113A 122A End cover Ball bearings Plug – oil fill Stationary shaft 122B 141C 144A 157A 178S1 178Y 197B1 Drive shaft Clamp ring Rub ring Bearing spacer – radial Key – impeller to bearings Key – drive carrier Bearing – radial 197C1 197D1 Bearing, reverse thrust Bearing – impeller thrust 2031 228 241 319 332A 333D1 351G1 355A
Parts Listings and Cross-Sectionals Item 412M1 Part name O-ring – containment shell 418 426A 496G1 Hex tap bolt – jacking Hex capscrew – casing drain O-ring – drive magnet assembly 5291 740A 740B 750 Washer – wave spring Drive magnet assembly Drive carrier Containment shell 1 Material Standard: Viton Optional: EPDM Optional: Teflon Optional: Chemraz 505 Optional: Kalrez 4079 304 SS 304 SS Standard: Viton Optional: EPDM Optional: Teflon Optional: Chemraz 505 Optional: Kalrez 4079 Steel Tefzel / neodym
Parts Listings and Cross-Sectionals Figure 78: Two-piece impeller L group close-coupled parts list Item 100 101 101A1 Part name Casing Impeller assembly Bearing spider 122A Stationary shaft 141C 157A 178S1 178Y 197B1 Clamp ring Bearing spacer – radial Key – impeller to bearings Key – motor to carrier Bearing – radial 197C1 197D1 Bearing – reverse thrust Bearing – impeller thrust 2031 222L 228 241 351G1 356A 358 360W1 361H 370B 370F 371 408A 412M1 Wear ring – rear Setscrew Frame – close coupled Fr
Parts Listings and Cross-Sectionals Item 740A 740B 750 1 Recommended spare parts Part name Drive magnet assembly Drive carrier Containment shell Material Tefzel / neodymium iron Cast iron / neodymium iron Tefzel / fiber-reinforced vinylester SP3298 S group frame-mounted pump in sizes 1 x 1-1/2 - 6 and 2 x 3-6 SP3298 S group frame-mounted drawing SP3298 S group frame-mounted parts list Item 100 100U 101 101A1 109A 1121 113A 122A 122B 141C 157A 178S1 178Y 197B1 100 Part name Casing Volute insert Impelle
Parts Listings and Cross-Sectionals Item 197C1 197D1 Part name Bearing – reverse thrust Bearing – impeller thrust 203 228 319 332A1 333D1 355A1 356A 360A1 360W 370B 370C 372V 408A 408J 412M1 Wear ring – rear Frame – bearing Sight window Labyrinth seal Lip seal Flanged hex nut Hex capscrew – clamp ring to backplate Gasket – end cover to frame Gasket – frame to clamp ring Hex capscrew – frame to clamp ring Hex capscrew – end cover to frame Hex capscrew – backplate to casing Plug – drain Plug – oiler O-ring
Parts Listings and Cross-Sectionals SP3298 S group close-coupled pump in sizes 1 x 1-1/2 - 6 and 2 x 3 -6 SP3298 S group close-coupled drawing, with NEMA motor 102 3298 Family Installation, Operation, and Maintenance Manual
Parts Listings and Cross-Sectionals SP3298 S group close-coupled drawing, with IEC motor SP3298 S group close-coupled drawing Item 100 100U 101 101A1 122A 141C 157A 178S1 178Y 197B1 Part name Casing Volute insert Impeller assembly Bearing spider Stationary shaft Clamp ring Bearing spacer – radial Key – impeller to radial bearings Key – motor to drive carrier Bearing – radial 197C1 197D1 Bearing – reverse thrust Bearing – impeller thrust 222L 228 356A 360W1 370B 372V 412M1 Setscrew Frame – close coupl
Parts Listings and Cross-Sectionals Item 412V1 Part name O-ring – backplate 444 492A 740B 750 811 811A 811B 811C 811D 1 Recommended spare parts Backplate Plug – access hole Drive magnet assembly Containment shell Cover – casing drain Cover – casing fill Gasket – casing drain Gasket – casing fill Hex capscrew – drain cover Item 228 222L 371 388T 408A 492A 503 742B 1 Used with motor frame 132 and 160 only. 2 Used with motor frames 80 and 90 only.
Parts Listings and Cross-Sectionals V3298 close-coupled S group pump in sizes 1-1/2 x 2 - 6, 2 x 3 - 6, 11/2 x 2 - 8 and M group size 1-1/2 x 2 - 10 V3298 S and M group drawing, with NEMA motor 3298 Family Installation, Operation, and Maintenance Manual 105
Parts Listings and Cross-Sectionals V3298 S and M group drawing, with IEC motor V3298 close-coupled S and M group parts list Item 100 101 101A 122A 141C 157A 178S 178Y 197B Part name Casing Impeller assembly Bearing spider Stationary shaft Clamp ring Bearing spacer – radial Key – impeller to radial bearings Key – motor to magnet assembly Bearing – radial 197C 197D Bearing – reverse thrust Bearing – impeller thrust 203 222L 228 351G 356A 358 360W 370B 412M Wear ring – rear Setscrew Frame – close coupl
Parts Listings and Cross-Sectionals Item 388T 408A 492A 503 742B 1 Used with motor frame 132 and 160 only. 2 Used with motor frames 80 and 90 only.
Parts Listings and Cross-Sectionals 3298 S group interchangeability 3298 M group interchangeability 108 3298 Family Installation, Operation, and Maintenance Manual
Parts Listings and Cross-Sectionals 3298 M group interchangeability – size 1½ x 3-8 only 3298 L group interchangeability 3298 Family Installation, Operation, and Maintenance Manual 109
Parts Listings and Cross-Sectionals SP3298 S group interchangeability 110 3298 Family Installation, Operation, and Maintenance Manual
Parts Listings and Cross-Sectionals V3298 S group interchangeability V3298 M group interchangeability 3298 Family Installation, Operation, and Maintenance Manual 111
Parts Listings and Cross-Sectionals Hydraulic coverage charts 3298 charts 112 3298 Family Installation, Operation, and Maintenance Manual
Parts Listings and Cross-Sectionals SP3298 charts 3298 Family Installation, Operation, and Maintenance Manual 113
Parts Listings and Cross-Sectionals V3298 charts 114 3298 Family Installation, Operation, and Maintenance Manual
Other Relevant Documentation or Manuals Other Relevant Documentation or Manuals For additional documentation For any other relevant documentation or manuals, contact your ITT representative.
Local ITT Contacts Local ITT Contacts Regional offices Region North America (Headquarters) Asia Pacific Europe Latin America Middle East and Africa 116 Address ITT - Goulds Pumps 240 Fall Street Seneca Falls, NY 13148 USA ITT Industrial Process 10 Jalan Kilang #06-01 Singapore 159410 ITT - Goulds Pumps Millwey Rise Industrial Estate Axminster, Devon, England EX13 5HU ITT - Goulds Pumps Camino La Colina # 1448 Condominio Industrial El Rosal Huechuraba Santiago 8580000 Chile ITT - Goulds Pumps Achileos
Visit our website for the latest version of this document and more information: www.gouldspumps.com ITT - Goulds Pumps 240 Fall Street Seneca Falls, NY 13148 USA Tel. 1–315–568–2811 Fax 1–315–568–2418 © 2014 ITT Corporation The original instruction is in English. All non-English instructions are translations of the original instruction. Form en-US.2014-07.IOM.