Product Manual B

ManualsBrandsGPI ManualsAC Powered Fuel Pumps115V Fuel Transfer Pump — 30 GPM, Meter

Rev. C 92152501

General Information .................... 2

Installation ..................................3

Operation .................................... 3

Calibration ..................................4

Maintenance ...............................5

Troubleshooting .......................... 6

Specications .............................7

Illustrated Parts List ....................8

Parts and Service .......................9

TABLE OF CONTENTS

5252 East 36th Street North

Wichita, KS USA 67220-3205

316-686-7361 | FAX: 316-686-6746

800-835-0113 |

www.GPIpumps.net

“A Great Plains Ventures Subsidiary”

SAVE THESE INSTRUCTIONS

MR 5-30 or MR 5-30N Series

Fuel Meter

Owner’s Manual

To the owner…

Congratulations on receiving your GPI

MR 5-30 Meter. We are pleased to provide

you with a meter designed to give you

maximum reliability and efciency.

Our business is the design, manufacture and

marketing of liquid handling, agricultural and

recreational products. We succeed because

we provide customers with innovative,

reliable, safe, timely and competitively-

priced products. We pride ourselves in

conducting our business with integrity and

professionalism.

We are proud to provide you with a quality

product and the support you need to obtain

years of safe, dependable service.

Great Plains Industries, Inc. is a member

of the Petroleum Equipment Institute.

Victor Lukic, President

Great Plains Industries, Inc

12/12

Summary of content (12 pages)

PAGE 1
5252 East 36th Street North Wichita, KS USA 67220-3205 316-686-7361 | FAX: 316-686-6746 800-835-0113 | www.GPIpumps.
PAGE 2
GENERAL INFORMATION The purpose of this manual is to assist you in installing, operating and maintaining your mechanical fuel meter. Please take a few moments to read these instructions before installing and operating your fuel meter. SAFETY INSTRUCTIONS 1. This meter is designed for use only with thin viscosity petroleum fuels such as gasoline, gasoline/ethanol blends at levels designated as "gasohol" (E10 maximum), diesel and kerosene. 2.
PAGE 3
INSTALLATION Before installing your meter, review the safety instructions given above. Examine your meter to make sure there are no visible signs of shipment damage. Plan your meter installation by reviewing the following procedures. Your system must be mounted on a vented tank. If the tank is unvented, your local dealer or distributor can supply a pressure cap.
PAGE 4
other system components and there is no leakage. Promptly wipe spilled fuel from the meter’s exterior and other system components. flowrate is used. When topping off the calibration container, use a quick-open and quick-close method until the mark is reached. The large meter display represents the Batch Total for each fuel delivery. Before dispensing, reset the Batch Total to zero by turning the knob. (Figure 3) 4. Compare the meter display to the quantity in the container.
PAGE 5
MAINTENANCE The meter’s strainer should be cleaned at regular intervals, especially when low flow is detected. Clean or Replace Strainer 3. Wipe clean the inlet, housing, and O-ring groove. Coat the Oring with oil or light grease. Make sure the O-ring is fully seated. Replace the strainer. 1. Remove the nuts and bolts at the inlet fitting. Remove the fitting, O-ring, and strainer. 4. Position the inlet fitting in the desired orientation and tighten the nuts and bolts to 60 - 72 in-lb. 2.
PAGE 6
TROUBLESHOOTING Symptom Probable Cause Corrective Action A. Meter counter does 1. Broken counter assembly. Replace counter. not operate. (Normal fuel delivery) 2. Foreign material in counter Remove and clean counter assembly or nutator assembly. assembly or nutator assembly. 3. Broken nutator disc pin or defective nutator assembly. Install new nutator assembly. Replace bevel gear. 4. Missing or worn bevel gear. B. Meter counter does 1. Clogged strainer in meter. not operate. 2.
PAGE 7
SPECIFICATIONS Gallon Models Litre Models Unit of Measure U.S. Gallon Litre Flow Range 5 to 30 GPM 19 to 114 LPM -20° F to 125° F -29° C to 52° C Operating Temperature Typical Accuracy ± 2% ± 2% Nutating Disc Nutating Disc Housing Material Aluminum Aluminum Maximum Working Pressure 50 PSIG 3.4 bar 3/4"*, 1" or 1-1/2" 3/4"*, 1" or 1-1/2" NPT NPT or BSPP* Type Inlet/Outlet Fitting Size Threads Maximum Batch Total 999.9 9999 9,999,999.9 99,999,999 8.1 lbs. 3.
PAGE 8
ILLUSTRATED PARTS LIST A J B D I F C E G H Kits and Accessories Part No.
PAGE 9
Kits and Accessories, continued Kit No. Part No.
PAGE 10
PAGE 11
PAGE 12
Limited Warranty Policy Great Plains Industries, Inc. 5252 E. 36th Street North, Wichita, KS USA 67220-3205, hereby provides a limited warranty against defects in material and workmanship on all products manufactured by Great Plains Industries, Inc. This product includes a 2 year warranty from date of purchase as evidenced by the original sales receipt. A 30 month warranty from product date of manufacture will apply in cases where the original sales receipt is not available.