Product Manual

ManualsBrandsGPI ManualsDC Powered Fuel PumpsGPRO 12V Fuel Transfer Pump — 25 GPM, Automatic Nozzle, Hose

11/14

922106-01E

TABLE OF CONTENTS

General Information .................................................... 2

Safety Instructions ...................................................... 2

Installation .................................................................. 3

Operation .................................................................... 4

Maintenance ............................................................... 4

Repair ......................................................................... 4

Troubleshooting .......................................................... 5

Specications ............................................................. 6

Illustrated Parts Drawing ............................................ 7

Parts and Service ....................................................... 8

Warranty .......................................................See Insert

To the owner...

Congratulations on receiving your GPRO™ Fuel Transfer

Pump. We are pleased to provide you with a system designed

to give you maximum reliability and efciency.

Your fuel pump is designed, tested, and approved for use with

gasoline blends, diesel fuel blends and kerosene. Please take

all due precautions when handling these ammable liquids.

Your safety is important to us.

Also, to assure the longest possible service life, it is important

that you follow the operation and maintenance procedures

outlined in this manual. We are proud to provide you with a

quality product and dedicated support. Together with your

conscientious use, we are sure that you will obtain years of

safe, dependable service.

Victor Lukic, President

Great Plains Industries, Inc.

SAVE THESE INSTRUCTIONS

OWNER'S MANUAL

PRO25-012 PRO25-024

12-Volt DC 24-Volt DC

PRO25-012AD

Automatic Diesel Nozzle

PRO25-024AD

Automatic Diesel Nozzle

PRO25-012MD Manual Diesel Nozzle PRO25-024PO Pump Only

PRO25-012PO Pump Only

PRO25-012PO/XTS Pump Only - Extreme

Temperature Series

DO NOT RETURN THIS PRODUCT

TO THE STORE!

Please contact Great Plains Industries before returning any product.

If you are missing parts or experience problems with your installation,

our Customer

Support Department will be happy

to assist you:

800-835-0113 or 316-686-7361

Summary of content (8 pages)

PAGE 1
OWNER'S MANUAL SAVE THESE INSTRUCTIONS PRO25-012 PRO25-024 PRO25-012AD PRO25-012MD PRO25-012PO PRO25-012PO/XTS PRO25-024AD Automatic Diesel Nozzle PRO25-024PO Pump Only 12-Volt DC Automatic Diesel Nozzle Manual Diesel Nozzle Pump Only Pump Only - Extreme Temperature Series 24-Volt DC DO NOT RETURN THIS PRODUCT TO THE STORE! Please contact Great Plains Industries before returning any product.
PAGE 2
GENERAL INFORMATION WARNING The purpose of this manual is to assist you in installing, operating and maintaining your GPRO™ pump. This manual covers models PRO25-012 (12-Volt DC) and PRO25-024 (24-Volt DC). CAUTION WA R N I N G i n d i c a t e s a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
PAGE 3
If using solvent to clean pump components or tank, observe the solvent manufacturer’s recommendations for safe use and disposal. INSTALLATION Install Suction Pipe Trim the power cord to the desired length. If your power cord is not pre-stripped, strip 3 inches of outer insulation from the power cord end. Then strip 1/2 inch of insulation from the power cord wires. Slide the strain relief grip onto the power cord so that the threaded end of the strain relief grip faces the stripped power wires.
PAGE 4
DANGER If the pump is to be installed in a Hazardous (Classified) location, it must be installed by a licensed electrician and conform to National Fire Protection Association (NFPA) codes 30 and 70. You, as the owner, are responsible for seeing that the installation and operation of your pump complies with NFPA codes as well as any applicable state and local codes. Rigid conduit must be used to install wiring. Note that the lead wires are factory-sealed isolating the motor from the junction box.
PAGE 5
a soft-bristled brush and solvent. If the strainer is very dirty, compressed air may be used. If damaged, replace the strainer. Replace components making sure that they are seated and fasteners are tightened securely. WARNING Observe precautions against electrical shock when servicing the pump. Always disconnect power before repairing or servicing. Never apply electrical power to the system when any of the coverplates are removed. REPAIR Carefully inspect all parts for wear or damage.
PAGE 6
TROUBLESHOOTING SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION G. MOTOR OVERHEATS 1. 2. 3. 4. 5. Pump only low viscosity fluids. Clean filter assembly. Remove pump and clear suction pipe, replace as needed. Duty cycle is 30 minutes ON and 30 minutes OFF. Ball bearings damaged. UL Listing requires specific treatment for motor replacement, contact factory. Remove bypass poppet and clean. Pumping high viscosity fluids Clogged filter assembly Clogged or broken suction pipe Duty cycle too long Motor failure 6.
PAGE 7
ILLUSTRATED PARTS DRAWING 44 1 3 4 6 2 32 7 5 9 10 8 11 43 31 13 30 19 21 17 24 45 18 42 16 46 34 23 22 15 35 37 38 20 39 33 40 41 GPRO™ Item No. 1 2 3 4 5 6 7 8 9 10 11 13 15 16 17 18 19 20 21 22 23 24 30 31 32 34 Part No.
PAGE 8
PARTS AND SERVICE For warranty work, always be prepared with your original sales slip or other evidence of purchase date. In order to preserve the UL Listing for the motor, do not attempt to service the motor. For products serviced outside the factory, the UL nameplate must be defaced to indicate that the equipment may no longer meet the requirements for UL Listing. This does not apply to products serviced outside the factory under the UL program for Rebuilt Motors for Use in Hazardous Locations.