OWNERS MANUAL UPPERTONE Physical Therapy Equipment Model No. UT 93A GPK Inc., 535 Floyd Smith Dr., El Cajon, CA 92020, 800-468-8679, 619-593-7381, Fax: 619-593-7514, www.gpk.
TABLE OF CONTENTS Uppertone Parts List 3 Complete Assembly Instructions A. Frame Assembly B. Deltoid Lat Slider Assembly C. Deltoid/Lat Assembly D. Curl Assembly E. Weight Track Assembly F. Rowing Lever Assembly G. Cable Set Up H. Installing The Weights I. Installing the Rickshaw Handles J.
UPPERTONE PARTS LIST Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 30b 31 32 33 34 35 36 37 38 38b 39 40 41 42 43 44 44c 45 46 47 47b Description Main Frame Frame Base Frame Post Weight Track Rowing lever Deltoid/Lat Slider Rowing Adjuster Rowing Arm (Right & Left side) 10-24 Nut Black 4.25” Pegs.
UPPERTONE PARTS LIST Part No. 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 93 105 706 900 Description Comment Hex Bolts 3/8-16 X 2.75 Hex Bolts 3/8-16 X 3.25 4 if optional QuadAdjustable handle is ordered Hex Bolts 3/8-16 X 3.75 Hex Bolts 3/8-16 X 4 2" Sq.
COMPLETE ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: (1) 5/32” Allen wrench, (2) Adjustable open end wrench, (3) 7/16 open end, box end wrench (4) 9/16 open end, box end wrench, (5) 3/8 - 3/4", 3/8 drive socket set, (6) 3/8 drive ratchet wrench & extension Figure 1 shows how the UPPERTONE should look when it is fully assembled. Keep this figure in front of you at all times to help you assemble the UPPERTONE. A: Frame Assembly (Figures 1 & 2) 1.
2 1 FIGURE 1 B B A A 2 1
2 1 FIGURE 2 3 105 B B 1 WEIGHT STOP 400 39 67 39 42 67 65 42 14 67 42 67 A 2 52 42 65 A ROW STOP 48 56 65 65 900 56 2 67 67 51 1
2 1 FIGURE 3 6 B B 3 1 2 A 4 SHAFT COLLARS (32) BRONZE BEARINGS (65) 5 2 1 A
2 1 FIGURE 4 B B 25 24 45 67 23 67 42 93 A A 10 73 2 1
C: Deltoid/Lat Assembly (Figures 5) 1. Slide the bronze spacer (60) and then the 4 ½” pulley (17) over each of the ¾” shafts which are located near the center and protruding horizontally from the Delt/Lat slider. 2. Install the Swing Plates (26). There are 4 identical Swing Plates (26), 2 will be mounted horizontally, and 2 will be mounted vertically. Carefully follow the steps below: a. Slide one Spacer (61) over each shaft and push up against each 4 1/2#' Pulley (I7).
2 1 70 901S 36 49 14 B 31 37 42 12 B 45B 30 37 53 16 38B 6 56 40 54 42 56 60 62 17 63 61 51 45B 66 56 14 64 901S 63 42 26 14 50 36 44C 30B 53 41 64 32 54 56 28 65 16 29 A A 69 35 27 FIGURE 5 2 1
D: Curl Assembly (Figure 5) 1. Attach Pulley (14) to Curl Arm (3 0) with Spacers (56 &54) as shown in Figure 5. 2. Insert Bearings (66) into tube on Curl Arm (30). Mount Curl Arm (30), Pulley (16), Spacer (56) and Curl Elbow 3. Pivot Bracket (30.b.) with Spacers (54) onto Deltoid/Lat Slider (6) using 3/8 Hex Bolt (51) and Nut (42) as shown. NOTE:LEAVE NUT LOOSE ENOUGH FOR CURL ELBOW PIVOT BRACKET TO MOVE FREELY. 4.
2 1 FIGURE 6 B B WEIGHT 42 67 93 18 22 42 45 47 47 4 901L 21 38 16 A 2 A 1
2 1 FIGURE 7 36 59 20 41A 18 41A B B 20 81 54 44D 44 705 93 54 A 67 42 A 67 706 54 41A 2 67 1
F: Rowing Lever Assembly (Figures 1 & 8): 1. Insert Bearings (65) into tubes as shown. Attach Rowing Levers (5) to Frame Base (2) by inserting shaft on Rowing Levers into Bearings (65) at end of Frame Base (2). Secure with Shaft Collar (32) by sliding Shaft Collar over exposed shaft and tightening the set-screw with a 5/32 Allen wrench. Both Rowing Levers (5) should rest almost vertically against stops. NOTE: THE FOLLOWRNG INSTRUCTIONS (1.a through 1.i.) APPLY TO BOTH ROWING LEVERS. a.
2 1 FIGURE 8 47B 10 93 102 11 B B 37 67 45 9 45 40 56 8 67 67 7 37 42 12 5 34 42 54 42 54 A A 67 42 47 2 1
Hook Bolt (33) Curl Arm (30) 1 “front” sticker 9 2 4 5 10 7 3 8 6 Figure 9 11 Weight Truck (18) Weight Track (4) 14 15 Note: This figure shows the right Frame Leg.
8. Run Cable over Pulley on Curl Arm (30) and continue straight down next to Pulley (16). 9. Run Cable under Pulley (1 6) on Weight Track (4) and continue to run under lower Pulley (1 4) on Frame Base (2) Post. 10. Snake the Cable up through Pulley Bracket (13) mounted on Rowing Lever (5). 11. Run Cable back, under and around top Pulley on Frame Base (2) post. 12. Attach the end of Cable to the Rowing Lever (5). H: Installing the Weights 1. Add desired weights to Weight Truck (18).
2 1 FIGURE 12 RICKSHAW/TRICEP HANDLES INSTALLATION B B Shaft collar A A Secure shaft collars to the end of handles (one time only). Set-up deltoid/lat arms in LAT PULL position (use T-pins). Hang RICKSHAW/TRICEP HANDLES INSTALLATION over end of LAT PULL handles. Place heel of hand in padded cuff to do exercises. Remove RICKSHAW/TRICEP HANDLES when you are finished with exercises.
2 1 FIGURE 13 BACKREST INSTALLATION B With deltoid station set in position shown at right, pull T-pins out until arms are disengaged. Lift arms up to horizontal position and push T-pins in so they rest on top of brackets as shown below. B SHAFT COLLAR A BACKREST A Pull plugs out from the ends of deltoid handles. Slide handles in until they line up with BACKREST tubes. Slide BACKREST in place as shown above. Adjust BACKREST position with shaft collars.
BACK REST PARTS LIST Part No. BR01 BR02 87 80 96 BRFOAMPAD Description 1" Alum Tube 3/4" Alum Tube Back Rest Bolt 5/16 X 18 X 1.
2 1 FIGURE 14 12" Foam Pad 96 B B BR02 BR01 87 96 32 80 A A 32 2 1
ADJUSTABLE HANDLES PARTS LIST Part No. 73 82 86 89 92 94 95 98 Description Comment 4" Foam Pads Adj. Eyebolt 10-24 All Thread Bolt 5/16 X 18 X 4 Lock Nut 5/16 Thumb Bolt Adj. Handle 3/8" Nylon Washer Adj.
2 1 FIGURE 15 73 73 B B 10 93 93 42 67 10 67 93 94 45 37 9 67 98 56 67 40 67 92 45 8 89 82 A A 95 86 37 67 49 2 1
USING THE UPPERTONE CAUTION: PLEASE CONSULT WITH YOUR PHYSICIAN BEFORE BEGINNING A NEW EXERCISE PROGRAM. Please refer to the Exercise Manual and the videos on the CD that came with the Uppertone, for instructions on how to use it. In any case, while the manual describes the various exercises, we strongly suggest that you consult a physician or physical therapist before beginning any exercise program.
of the original receipt as proof of purchase. This warranty applies only if the Uppertone is used as described in the owners exercise manuals. It is void if the product is abused, tampered with, used unreasonably, or fails as a result of normal wear. This warranty is lieu of all other warranties, expressed or implied, including, but not limited to, the warranties of merchantability and fitness for a particular purpose. GPK is not liable for incidental or consequential damages of any kind.
