Pressure Roller Parts List

ManualsBrandsGraco Inc ManualsPower Roller245397

309445

Rev. E

To find your local Graco authorized service

center:

 Call us at 1–800–690–2894

 Visit our website at www.graco.com

INSTRUCTIONS–PARTS LIST

Important Safety Instructions

 Read all warnings and instructions

in this manual. Save these

instructions.

Pressure Roller with 20”

Heavy Duty Extension, EvenFlowt Roller

Frame and Contractort Inline Valve

– For the rolled application of architectural paints and

coatings –

Model 245397, Series C

 20 in. (50 cm) Heavy-Duty Extension

 9 in. (23 cm) EvenFlow Roller Frame

 1/2 in. (13 mm) Nap Roller Cover

 Contractor Inline Valve

3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure

The best operating pressure is the lowest pressure that provides

an even paint supply to the roller and typically does not exceed

300 psi (2.1 MPa, 21 bar).

CAUTION

Never leave water in the pump, inline valve, or roller frame.

Doing so could cause corrosion and damage from freezing.

For storage, flush the system with Graco Pump Armor or

mineral spirits/paint thinner.

GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441

Graco Inc. is registered to I.S. EN ISO 9001

Summary of content (10 pages)

PAGE 1
INSTRUCTIONS–PARTS LIST 309445 Rev. E Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. To find your local Graco authorized service center: Call us at 1–800–690–2894 Visit our website at www.graco.com Pressure Roller with 20” Heavy Duty Extension, EvenFlowt Roller Frame and Contractort Inline Valve – For the rolled application of architectural paints and coatings – Model 245397, Series C 20 in. (50 cm) Heavy-Duty Extension 9 in.
PAGE 2
Warnings and Cautions WARNING EQUIPMENT MISUSE HAZARD Misuse can cause the equipment to rupture or malfunction and result in serious injury. To help prevent injury Do not modify the extension tube or roller frame or use parts not designed for this equipment. Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in this or any other pressurized aluminum equipment.
PAGE 3
Installation Assemble pressure roller as shown in Parts Drawing, page 7. Attach pressure roller assembly to inline valve. When connecting EvenFlow roller frame to the Contractor Inline Valve, use a wrench to tighten. Pressure Relief Procedure WARNING To help prevent injection injuries, follow this procedure whenever you stop painting. psi/MPa/bar 1. Put inline valve trigger safety in SAFETY ON position (Fig. 1). 2. Shut off power to pump. 3.
PAGE 4
Operation WARNING SKIN INJECTION HAZARD To reduce the risk of a fluid injection injury, do not operate the inline valve with the tip guard or trigger guard removed. The Contractor Inline Valve can be used as an airless spray gun by attaching a Handtite Guard and RAC5 Switchtip. 1. Follow pump priming instructions using lowest pressure setting at which pump primes. 2. Turn prime/spray valve to SPRAY position.
PAGE 5
. Prime pump with water or flushing fluid for oil– based materials. Use the lowest pump priming pressure setting. Cleaning Contractor Inline Valve 1. Relieve pressure, page 3. 6. Turn prime/spray valve to SPRAY. NOTE: Perform Step 7 at the lowest pressure possible. 7. Trigger inline valve until flushing fluid begins to dilute the paint. 8. Place roller frame (1) in another bucket and continue flushing until fluid coming out of the roller frame (1) is clear. 2.
PAGE 6
Notes 6 309445
PAGE 7
Parts List Model 245397, Series A 23 4 1 5 2 12 ti10642a 19 Ref. No. Part No. Description 1 2 4 244271* 245999 246277 1 1 5 7 197106 15H622 FRAME, roller CAP, end (includes seal and retainer) CAP, end (includes seal, retainer, and o–ring) CLIP, roller GASKET 12 115524 GASKET 1 14 232122 EXTENSION, 20 in. (50 cm) 1 19 107590 ROLLER, cover, 9 inch, 1/2 in. (13 mm) nap 1 DIFFUSER 2 23 15B065 Qty. 1 1 1 *244271 Frame includes 1, 2, 4, 5, 12, 19, 23.
PAGE 8
Parts List 101 108 119 111 110 105a 120 106 105b 107 102 105 105c 113 105d 103 114 112 104 8 309445 TI0667
PAGE 9
Parts List Contractort In–line Valve Model 244161 Ref. No. Part No. Description 101 102 218070 244193 NEEDLE–DIFFUSER/SEAT KIT TRIGGER, valve, In–line (includes 107) GUARD, trigger KIT, swivel FLUID FILTER ASSEMBLY (standard 50 mesh) includes replacement parts 5a, 5b, 5c, 5d RETAINER, spring ELEMENT, strainer SPRING, compression RETAINER, spring SEAL, sleeve 103 196869 104 238817 105 218131 105a 105b 105c 105d 106 179722 179731 179763 179750 179733 Qty. 1 1 1 1 1 1 1 1 1 1 Ref. No.
PAGE 10
Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.