Instructions / Assembly

ManualsBrandsGraco ManualsPaintTexSpray RTX 2000PI Texture Sprayer

Table Of Contents

Quick Guide

RTX2000 Texture

Sprayers

For Water-Based Materials Only. 3A3482A - EN

Step 1: Connect air hose and material hose to sprayer air and material hose outlets. Step 2: Close

prime valve and close gun air control valve. Step 3: Connect air hose to gun. Step 4: Connect material

hose to gun. Step 5: Install burp guard. Step 6: Install spray nozzle. Step 7: Pour one gallon of water

into material hopper. Step 8: Turn ON/OFF switch to

position. Step 9: Close gun air control valve.

Open prime valve to start flow. Step 10: Point gun into waste bucket and pull trigger to pump water

through the system until material hopper is empty. Step 11: See Mixing Material. Add premixed mix to

material hopper. Step 12: Trigger gun into a waste bucket until a steady stream of material sprays out

of the gun. Release trigger.

Read Operation manual 3A3258 for complete instructions and warnings.

Manuals are available by calling Graco at 1-800-690-2894, or at

www.graco.com.

For Technical Assistance call 1.800.543.0339

This Quick Guide is not a substitute for reading and understanding all operation manuals

and warning labels supplied with the equipment. It is important that you read and

understand all warnings and instructions before operating this equipment.

Follow the pressure relief procedure and wear protective equipment including but not

limited to protective eye wear.

FAILURE TO FOLLOW ALL WARNINGS CAN RESULT IN SERIOUS INJURY.

SETUP

NOZZLE SELECTION CHART

Application WideTex™ Disc Nozzle (mm) Air Volume

Standard Hardened

Simulated Acoustic - Fine W6 W6H 4high

- Medium W8 W8H 6high

- Course W10 W10H 8- 10 high

Fog W4 W4H 3high

Orange peel W4 or W6 W4H or W6H 3 - 8 medium to high

Splatter coat W6 or W8 W6H or W8H 6 - 10 low to medium

Knockdown W6 or W8 W6H or W8H 6 - 8 low

1 2 3 4 5 6

ti28566a

7 8 9 10 11

Summary of content (5 pages)

PAGE 1
Quick Guide RTX2000 Texture Sprayers For Water-Based Materials Only. 3A3482A - EN Read Operation manual 3A3258 for complete instructions and warnings. Manuals are available by calling Graco at 1-800-690-2894, or at www.graco.com. For Technical Assistance call 1.800.543.0339 This Quick Guide is not a substitute for reading and understanding all operation manuals and warning labels supplied with the equipment.
PAGE 2
PRESSURE RELIEF PROCEDURE 1 2 3 ti ti28565a ti OPERATION Soft Start/Smart Start™ • Smart Start keeps the sprayer at full operating pressure and allows the sprayer to spray • immediately when the gun is triggered. Soft Start prevents a large “splotch” of material from being discharged from the gun when trigger is pulled after the sprayer has sat idle for a period of time.
PAGE 3
Texture Spraying 1. Wet inside of hose before each use to flush out sediment and prevent texture material from packing out hose. a. Pour one gallon (3.8 liters) of water into the material hopper. b. Open gun air control valve. Turn ON/OFF switch to ON position. Aim gun into hopper and trigger gun to circulate water for a few minutes to wet inside of material hose. c. Trigger gun into waste pail until hopper no longer contains water and all water is removed from hose and pump system. System priming. a.
PAGE 4
MIXING MATERIAL Correct material mixture is essential for a successful project. Drywall Compound • Mix the material with water in a separate container before pouring it into hopper. • Dry Mix: Carefully mix material and water according to manufacturer instructions. • Premix: Follow manufacturers recommendations for mixing. • Use Material Thickness Gauge to determine if mixture is thin enough to spray. Be sure gauge is completely dry and clean every time it is used.
PAGE 5
DO NOT PRINT THIS PAGE -- PRINTING DO NOT PRINT THIS PAGE -- PRINTING INSTRUCTIONS Printing Instructions: 1. Size: 8.5 x 11 folded to 5.5 x 8.5 2. 1.5 mil lam with sealed edge 3. 0.2 inch diameter hole punch in top left corner after folding 4. Stock: 100# Gloss Cvr Part must be RoHS compliant.