User's Manual

ManualsBrandsGraco ManualsAir Compressors307879R

307879R

Instructions - Parts List

15:1 Ratio Fire-Ball

Undercoater Pumps

Portable stationary units for filled undercoating materials. For professional use only.

Model 222077

35 lb. portable dispense kit and cover

Model 226342

120 lb. rollaround dispense kit and cover

Model 226269

400 lb. stationary dispense kit and cover

2250 psi (15.5 MPa, 155 bar) Maximum Working

Pressure

180 psi (1.2 MPa, 12 bar) Maximum Incoming Air

Pressure

Important Safety Instructions

Read all warnings and instructions in this

manual. Save these instructions.

These systems are designed to be used only in

pumping petroleum-based undercoating materials.

Any other use of the system can cause unsafe

operating conditions and result in component rupture,

fire, or explosion which can cause serious bodily

injury, including fluid injection.

Summary of content (10 pages)

PAGE 1
Instructions - Parts List 15:1 Ratio Fire-Ball® Undercoater Pumps 307879R Portable stationary units for filled undercoating materials. For professional use only. Model 222077 35 lb. portable dispense kit and cover Model 226342 120 lb. rollaround dispense kit and cover Model 226269 400 lb. stationary dispense kit and cover 2250 psi (15.5 MPa, 155 bar) Maximum Working Pressure 180 psi (1.
PAGE 2
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
PAGE 3
Warnings WARNING EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals. • Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings.
PAGE 4
Installation Installation Grounding The equipment must be grounded to reduce the risk of static sparking and electric shock. Electric or static sparking can cause fumes to ignite or explode. Improper grounding can cause electric shock. Grounding provides an escape wire for the electric current. To ground the pump: Remove the ground screw (Z) and insert through the eye of the ring at the end of the ground wire (Y). Fasten the ground screw back onto the pump and tighten securely.
PAGE 5
Installation Typical Installation Air Line and Accessories This typical installation is only a guide for selecting and installing a system. It is not an actual system design. Contact your Graco distributor for assistance in designing a system to suit your needs. NOTE: Install the air line accessories in the order shown in FIG. 2. D 1. Install a pump runaway valve (G) to shut off the air to the pump if the pump accelerates beyond the pre-adjusted setting.
PAGE 6
Operation Operation Pressure Relief Procedure Follow the Pressure Relief Procedure whenever you see this symbol. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. 2. Open the master air valve from the compressor. 3.
PAGE 7
Operation NOTICE Never allow a pump to run dry of fluid being pumped. A dry pump quickly accelerates to a high speed, possibly damaging itsself, and it may get very hot. NOTE: A pump runaway valve can be installed on the air line to automaticaly shut off the pump if it starts to run too fast. See page 5. 7. Read and follow the instructions supplied with each component. 8. Whenever you shut off the system always follow the Pressure Relief Procedure on page 6.
PAGE 8
Operation Model 226342 120 lb. Drum Size Unit with Dolly 1 3 2 4e 4c 4b 4a 4d Ref. 1 2 3 4 4a 4b 4c 4d 4e 8 Part Description Qty.
PAGE 9
Operation 112 1 111 109 107 101 110 106 108 113 102 114 103 3 Model 226269 400 lb Stationary Drum Size Unit Ref. 1 2 3 Part Description Qty. 206700 PUMP, 15:1 Fire-Ball, See 306531 1 for parts 222082 DISPENSE KIT, see page 1 200326 COVER, drum 1 307879R Dispense Kit 222082 Ref. 101 102 103 106 107 108 109 110 111 112 113 114 Part Description Qty.
PAGE 10
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.