User's Manual

ManualsBrandsGraco ManualsDo-It-Yourself tools309234H

Coriolis Fluid Flow Meter

Instructions–Parts List

309234H

Important Safety Instructions

Read all warnings and instructions in this manual and

in your proportioner manual. Save these instructions.

The meter and meter kit are intended for installation and use on a PrecisionMix II fluid

panel in non–hazardous environments only. If a Coriolis meter is installed on a

PrecisionMix II, the entire system is no longer approved for a hazardous environment.

Not approved for use in explosive atmospheres or hazardous locations.

For professional use only.

5000 psi (34 MPa, 345 bar) Maximum Working Pressure

Part No. 116158 Bare Meter

.01 to 0.5 gpm (40 to 2,000 cc/min.) Flow Range.

Part No. 244039 Meter Kit

Includes Part No. 116158 Bare Meter, mounting hardware, and fittings.

2300 psi (16 MPa, 160 bar) Maximum Working Pressure

Part No. 15D135 Bare Meter

.01 to 0.5 gpm (40 to 2,000 cc/min.) Flow Range.

Part No. 15D599 Meter Kit

Includes Part No. 15D135 Bare Meter, mounting hardware, and fittings.

TI0624a

II 2 G EEx de IIC

Summary of content (14 pages)

PAGE 1
Instructions–Parts List Coriolis Fluid Flow Meter 309234H EN The meter and meter kit are intended for installation and use on a PrecisionMix II fluid panel in non–hazardous environments only. If a Coriolis meter is installed on a PrecisionMix II, the entire system is no longer approved for a hazardous environment. Not approved for use in explosive atmospheres or hazardous locations. For professional use only.
PAGE 2
Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2 309234 Technical Data . . . . . . . . . . . . . . . . .
PAGE 3
WARNING SKIN INJECTION HAZARD Spray from leaks, or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin can also cause serious injury. Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate surgical treatment. Do not stop or deflect fluid leaks with your hand, body, glove, or rag.
PAGE 4
Installation WARNING FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD To reduce the risk of fire, explosion, or electric shock: All electrical equipment must only be installed by a qualified electrician. Mounting the Flow Meter CAUTION The bare meter weighs 33 lb (15 kg). Do not mount the meter in the fluid line without proper support, to prevent stress on the fluid inlet and outlet connections. See Fig. 1.
PAGE 5
Installation Vertical Mounting Grounding When mounting on a vertical surface, the preferred fluid flow is upward through the meter. See Fig. 2. This allows solids to settle out and air to rise away from the metering tube. This also allows thorough draining of the meter during shutdown, to prevent fluid from drying in the meter. Downward flow is permitted if a check valve is installed at the meter outlet to prevent fluid from falling through the meter.
PAGE 6
Operation Pressure Relief Procedure WARNING INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. Fluid under high pressure can be injected through the skin and cause serious injury. To reduce the risk of an injury from injection, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you: are instructed to relieve the pressure, stop spraying, check or service any of the system equipment. 1.
PAGE 7
Operation Measuring values Using the ProMass 80A with a Graco PrecisionMix II System The following will list values per the E&H function matrix. If a value isn’t mentioned, the the default E&H settings will suffice. Generic Settings for Basic Installation with a PrecisionMix II System The function matrix is a two level construct: groups and functions. The groups, being the highest level, are compromised by multiple functions.
PAGE 8
309234 LANGUAGE ASSIGN LINE 1 ASSIGN TOTALIZER OPERATION USER INTERFACE OPERATION MODE PULSE/FREQ. OUT. TAG NAME COMMUNICATION SIM. FAILSAFE MODE SERIAL NUMBER SW–REV. AMP. SIMULAT. SYSTEM SENSOR VERSION AMP. HW VERSION DENSITY COEF. C 2 ACTUAL SYS. COND. K–FACTOR SENSOR DATA SUPERVISION INSTL. DIR. SENSOR SYSTEM PARAMETER DENSITY ADJUST ASSIGN LF–CUT OFF ASSIGN STATUS IN STATUS INPUT PROCESS PARAM. ASSIGN STATUS STATUS OUTPUT SIMULATION FREQ.
PAGE 9
Parts Use Only Genuine Graco Parts and Accessories Part No. 244039 and 15D599 Coriolis Meter Kit, for solvent-borne materials (0.8–2000 cps) Ref. No. 1 Part No. Description 116158 METER, Coriolis; for solvent and water-borne materials that cannot be handled through a gear meter (244039 only) METER, Coriolis; same as above (15D599 only) BRACKET, mounting CABLE, 4 conductor; 10 ft (3.05 m) CONNECTOR, cable SCREW, cap, socket head; 1/4–20 x 1 in. (25 mm) SCREW, cap, hex head; 1/4–20 x 1 in.
PAGE 10
Dimensions D N R P J C H A Dia G E F K M L B S T Four 0.26 in. (6.6 mm) holes TI0852A Diameter (ANSI) Dia. A B C D E F G H 1/8 in. 0.138 in. 1.26 in. 7.88 in. 11.0 in. 8.23 in. 5.90 in. 6.89 in. 8.66 in. 12.3 in. (3.5 mm) (32 mm) (200 mm) (279 mm) (209 mm) (150 mm) (175 mm) (220 mm) (312 mm) J K L M N P R S T Weight 6.16 in. 9.45 in. 22.4 in. 17.1 in. 7.50 in. 6.73 in. 7.26 in. 3.86 in. 4.34 in.
PAGE 11
Technical Data for Bare Meter Category Data Category Data Maximum Working Fluid Pressure Model 116158: 5000 psi (34 MPa, 345 bar) Model 15D135: 2300 psi (16 MPa, 160 bar) Flow Meter Inlet/Outlet 1/4 npt(f) Resolution ≈ 0.119 cc/pulse Accuracy + 0.5 %* Supply Voltage 24 Vdc Wetted Parts 303 and 440C Stainless Steel, PTFE Flow Range 0.01–0.5 gpm (40–2,000 cc/min) Fluid Temperature Range 40–180 Maximum Ambient Temperature 180 Fluid Viscosity Range 0.
PAGE 12
Wiring Diagram for PrecisionMix II and PrecisionMix II 3K 60 Series Meter Wiring Detail 1082 2021 1082 2021 A–4251, B–4271, C–4291 1082 TI0625a 80 Series Meter Wiring Detail 1082 2021 1082 2021 A–4251, B–4271, C–4291 1082 TI0625a 12 309234
PAGE 13
Notes 309234 13
PAGE 14
Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.