User's Manual

ManualsBrandsGraco ManualsFiltersGraco 310652K - CleanLine Filter

Instructions - Parts List

CleanLine

™

Filter

For petroleum-based oils, synthetic oils and anti-freeze* mixtures.

Not for use in explosive atmospheres.

*CleanLine 1800 filters must be used for anti-freeze mixtures,

CleanLine 900 filters are not compatible with anti-freeze.

Model 248418 Wall Mount CleanLine 900 Filter Assembly

900 psi (6.2 Mpa 62 bar) Maximum Working Pressure

Model 248421 Pump Mount CleanLine 900 Filter Assembly

900 psi (6.2 Mpa 62 bar) Maximum Working Pressure

Model 248417 Wall Mount CleanLine 1800 Filter Assembly

1800 psi (12.4 Mpa 124 bar) Maximum Working Pressure

Model 248419 Pump Mount CleanLine 1800 Filter Assembly

1800 psi (12.4 Mpa 124 bar) Maximum Working Pressure

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

310652K

ENG

TI6278B

Model 248421 shown

Summary of content (12 pages)

PAGE 1
Instructions - Parts List CleanLine™ Filter 310652K ENG For petroleum-based oils, synthetic oils and anti-freeze* mixtures. Not for use in explosive atmospheres. *CleanLine 1800 filters must be used for anti-freeze mixtures, CleanLine 900 filters are not compatible with anti-freeze. Model 248418 Wall Mount CleanLine 900 Filter Assembly 900 psi (6.2 Mpa 62 bar) Maximum Working Pressure Model 248421 Pump Mount CleanLine 900 Filter Assembly 900 psi (6.
PAGE 2
Warnings Warnings The following warnings include general safety information for this equipment. More specific warnings are included in the text where applicable. WARNING SKIN INJECTION HAZARD High-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Seek immediate surgical treatment. • Do not stop or deflect leaks with your hand, body, glove, or rag.
PAGE 3
Installation Installation The CleanLine Filter™ is installed upstream from the dispense equipment. It can be pump or wall-mounted. Wall Mount Clean Line 900 Installation Wall Mount Clean Line 1800 Installation K K J F J H H F E E G G D ti10680a ti5127 FIG. 2 FIG. 1 KEY KEY DESCRIPTION, See FIG. 2. DESCRIPTION, See FIG. 2. D Thermal Pressure Relief Kit must be installed downstream from the pump. The Thermal Pressure Relief Kit will vary based on the pump selected. See manual 308403.
PAGE 4
Installation Wall-mount 1. Fasten the wall-mount bracket (part no. 249568) to the wall using screws long enough to provide secure support. See FIG. 3. 2. Observe the flow-direction arrows on the top of the filter assembly. See FIG. 5. Position the filter assembly correctly and secure the assembly to the bracket using four screws (10) for models 248418 and 248421 or three screws (107) for models 248417 and 248419. Part No. 249565 Pump Mount Part No. 249568 Wall Mount FIG. 4 FIG. 3 Pump-mount 1.
PAGE 5
Operation Operation Relieve Pressure Flush System Flush the system before installing meters and for ongoing operation for all service fluids. Follow this procedure for each dispense location in the system, starting at the location farthest from the pump. WARNING Follow Relieve Pressure procedure before replacing CleanLine Filter cartridge. Read warnings on page 2. WARNING CleanLine 900 Filter (models 248418 and 248421) 1. Turn off air supply to pump. 2. Close upstream and downstream ball valves (6).
PAGE 6
Operation 4. Ensure the main fluid outlet valve at the pump is closed. 4. Unscrew the filter (5). 5. Apply oil to the new filter seal. 5. Place dispense end of hose into a waste oil container. Secure the hose so it will not come out during flushing. 6. Slowly open the main fluid outlet valve at the pump. At the same time, gradually increase the air pressure to the pump until there is good flow through the hose. 7.
PAGE 7
Operation 310652K 7
PAGE 8
Parts for CleanLine 900 Filter Parts for CleanLine 900 Filter Model 248418 Wall Mount CleanLine Filter Assembly Model 248421 Pump Mount CleanLine Filter Assembly 14 13 2 3 12 17★ ◆16 2 14 9 10 11 6 To dispense system 8 18a◆ 18b★ 6 4 7 3 2 1 Torque to 130-150 in-lb. 2 Apply sealant. 3 Route tube to used oil container or to bulk oil tank, not to TLM port. 1 1 2 8 5 From pump Ref.
PAGE 9
Parts for CleanLine 1800 Filter Parts for CleanLine 1800 Filter Model 248417 Wall Mount CleanLine Filter Assembly Model 248419 Pump Mount CleanLine Filter Assembly 109◆ 107 To dispense system 106 112 110 106 101 105 105 101 102 111a◆ 111b★ 1 Torque to 15 ft-lb. 103 1 A CleanLine Filter must be used when you use a Matrix fluid management system to dispense oil or anti-freeze.
PAGE 10
Technical Data Technical Data Maximum Working Pressure CleanLine 900 Filter (models 248418 and 248421) 900 psi (6.2 MPa, 62 bar) CleanLine 1800 Filter (models 248417 and 248419) 1800 psi (12.
PAGE 11
Dimensions Dimensions Part No. 249568 5.5” Part No. 249565 12.25” 7” 4” 7” .375” 13” 2.25” .75” 2.25” 2” 4” Part No.
PAGE 12
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.