User's Manual

ManualsBrandsGraco ManualsElectric Lubrication PumpsGraco 311306C- Oil Transfer Pump

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441

311306C

Instructions - Parts List

APEX

Oil Transfer Pump

For pumping non-flammable fluids including motor oils, hydraulic

fluid, and antifreeze. Do not use to pump water.

Model 260105, 3.0 gpm (11 lpm), 115 VAC (wall mount)

Model 260106, 3.0 gpm (11 lpm), 115 VAC

Model 260108, 4.2 gpm (16 lpm), 115 VAC

Model 260109, 7.9 gpm (30 lpm), 115 VAC

Model 260240, 6.3 gpm (24 lpm), 12 VDC (reversible)

150 psi (1.03 MPa, 10.3 bar) Maximum Working Pressure

Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Mounting Pump on Barrel or Tank . . . . . . . . . . . . . . . . 4

Mounting Pump In-line . . . . . . . . . . . . . . . . . . . . . . . . . 4

Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Electrical Installation

12 VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Performance Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . . 14

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Important Safety Instructions

Read all warnings and instructions in this

manual. Save these instructions.

Summary of content (14 pages)

PAGE 1
Instructions - Parts List APEX Oil Transfer Pump 311306C For pumping non-flammable fluids including motor oils, hydraulic fluid, and antifreeze. Do not use to pump water. Model 260105, 3.0 gpm (11 lpm), 115 VAC (wall mount) Model 260106, 3.0 gpm (11 lpm), 115 VAC Model 260108, 4.2 gpm (16 lpm), 115 VAC Model 260109, 7.9 gpm (30 lpm), 115 VAC Model 260240, 6.3 gpm (24 lpm), 12 VDC (reversible) 150 psi (1.03 MPa, 10.
PAGE 2
Warnings Warnings The following general warnings are for the setup, use, grounding, maintenance, and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings. When these symbols appear throughout the manual, refer back to these pages for a description of the specific hazard.
PAGE 3
Warnings WARNING PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow Pressure Relief Procedure in this manual, when you stop dispensing and before cleaning, checking, or servicing equipment. • Tighten all fluid connections before operating the equipment. • Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
PAGE 4
Installation Installation 4. Apply pipe sealant to threads and install pipe into pump inlet. These pumps are positive displacement gear pumps. The models with AC motors are 115 VAC, and use UL and CSA listed TENV motors. The motors use sealed bearings and require minimal maintenance. These pumps are for use with motor oil, hydraulic fluid, antifreeze, gear lubes and other oil-based products. Models 260106, 260108, and 260109 include a bung adapter for mounting on any standard 2 inch barrel or tank bung.
PAGE 5
Operation Electrical Installation Operation 115VAC The pump comes pre-wired with a 30 in. (762 mm) power cord with a 3 prong grounded plug. Power to the pump must be 115VAC, 60Hz, single phase. If an extension cord is used it should be a 3-wire cord with a ground. To permanently hardwire the pump, remove the conduit box cover and remove the power cord strain relief. The conduit box wiring opening is for a 1/2 in. conduit pipe.
PAGE 6
Troubleshooting Troubleshooting Problem Motor runs but pump will not prime. Oil leaking in motor mount. 6 Cause Solution Dirt under pressure relief valve Remove pressure relief valve or seal. and inspect, clean, or replace if damaged. Worn or damaged gears. Remove cover and inspect gears. Replace if worn or damaged. Fluid level low. Refill tank. Cover seal damaged. Replace if worn or damaged. Inlet strainer clogged. Remove and clean or replace. Air leak in suction tube.
PAGE 7
Troubleshooting Problem Unit pumps but output flow is low. Motor stalls when nozzle is closed. Motor overheating. Switch will not turn pump on. 311306C Cause Solution Clogged inlet strainer (12). Air leak in suction tube. Clean or replace. Check to make sure all joints in suction tube are sealed. Suction tube too close to tank Suction tube must have a 2 in. bottom. (51 mm) minimum clearance. Tank empty. Refill tank. Tank not vented. Tank must be vented to atmosphere. Worn or damaged gears.
PAGE 8
Parts Parts Models 260105, 260106, 260108, 260109 5 4 15 3 2 7 9 14 12 1 13 8 10 11 6 Ref. No. Description Qty.
PAGE 9
Parts Kits Kit Number Description 260061 ADAPTER, bung 260245 KIT, fluid, 3 gpm with swivel (model 260106) 260246 KIT, fluid, 3 gpm without swivel (model 260105) 260247 KIT, fluid with swivel (models 260108, 260109, 260240) 260248 KIT, motor, 115 VAC 3/4 HP (models 260105, 260106, 260108) 260249 KIT, motor, 115 VAC 1 HP (model 260109) 260292 KIT, packing 260293 KIT, gear, high flow (models 260108, 260109, 260240) 260294 KIT, gear (models 260105, 260106) 260295 KIT, pressure relief 260541 KIT, MOTOR, 12 VDC
PAGE 10
Technical Data Technical Data Maximum working pressure Output flow Inlet size Outlet size Weight Dimensions Power cord Horsepower Max current Wetted parts 10 150 psi (1.05 MPa, 10.5 bar) Model 260105: 3.0 gpm (11 lpm) Model 260106: 3.0 gpm (11 lpm) Model 260108: 4.2 gpm (16 lpm) Model 260109: 7.9 gpm (30 lpm) Model 260240: 6.3 gpm (24 Ipm) 1 in. npt 3/4 in. npt Model 260105, 260106, 260108: 25 lb (11.25 kg) Model 260109: 30 lb (13.5 kg) Model 260240: 28 lb (12.7 kg) See page 11 30 in.
PAGE 11
Technical Data Dimensions A B C Models 260105 260106 260108 260109 260240 311306C Length (A) Inches mm 13 330.2 13 330.2 13 330.2 13 330.2 13 330.2 Height (B) Inches mm 8 203.2 8 203.2 8 203.2 8 203.2 8 203.2 Width (C) Inches mm 7.75 196.8 7.75 196.8 7.75 196.8 6.25 158.7 6.25 158.
PAGE 12
Technical Data Performance Chart &,5)$ /54,%4 02%3352% PSI BAR -0A " # ! $ GPM LPM &,/7 2!4% 0!24 .5-"%23 ,%'%.
PAGE 13
Notes Notes 311306C 13
PAGE 14
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.