Repair - Parts Supply Systems 313527V EN For transferring or dispensing sealants, adhesives, or other medium to high viscosity fluids. For professional use only. Not approved for use in European explosive atmosphere locations. L20c 2 inch single post elevator 20 liter (5 gallon) size 100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure S20 3 inch single post 20 liter (5 gallon) size 125 psi (0.9 MPa, 9 bar) Maximum Air Inlet Pressure D60 3 inch dual post 60 liter (16 gallon) size 150 psi (1.
Table of Contents Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Component Identification . . . . . . . . . . . . . . . . . . . 10 D200 3 in. and D200s 6.5 in. Dual Post . . . . . . 10 S20 3 in. Single Post and D60 3 in. Dual Post . 11 Integrated Air Control Module . . . . . . . . . . . . . . 12 Integrated Air Line Accessories .
Related Manuals Related Manuals The following manuals are available at www.graco.com.
Warnings Warnings WARNING SKIN INJECTION HAZARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Do not point gun at anyone or at any part of the body. • Do not put your hand over the dispense outlet. • Do not stop or deflect leaks with your hand, body, glove, or rag.
Warnings WARNING ELECTRIC SHOCK HAZARD This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock. • Turn off and disconnect power cord before servicing equipment. • Use only grounded electrical outlets. • Use only 3-wire extension cords. • Ensure ground prongs are intact on power and extension cords. • Do not expose to rain. Store indoors. SPLATTER HAZARD Hot or toxic fluid can cause serious injury if splashed in the eyes or on skin.
Models Models Check the identification plate (ID) for the 6-digit part number of the supply system. Use the following matrix to define the construction of the supply system, based on the six digits. For example, Part No. CM14BA represents a Check-Mate supply system (CM), a carbon steel Check-Mate 100 MaxLife® displacement pump with an NXT 2200 air motor with remote DataTrak (pump code 14), a 3 in. dual post ram with integrated air controls (B) and a 55-gallon, uncoated platen with a neoprene seal (A).
Models CM First and Third and Second Digit Fourth Digit CM (Supply System with Check-Mate displacement pump) GD (Supply System with Dura-Flo displacement pump) Pump Code (See Table 1 for 2-digit Check-Mate Pump Code) (See Table 2 for 2-digit Dura-Flo Pump Code) KEY: S = Single post ram c = Cart mounted D = Dual post ram * B A Fifth Digit Sixth Digit Ram Options Platen and Seal Options 14 Size Style DataTra k Voltage 1 2 in. L20c no volt Air Control Panel B 2 3 in.
Models Table 1: Check-Mate Pump Code/Part No. Index Pump Part No.
Models Table 2: Dura-Flo Pump Identification Code/Part No. Index Pump Part No.
Component Identification Component Identification D200 3 in. and D200s 6.5 in. Dual Post W CM14BA Model Shown V Lift Locations N E U T H (Note: Do not use motor lift ring to lift entire system.) A X B G S R K M C P J D TI10430a FIG. 1 Key: A B C D F G H J K M 10 Ram Assembly Air Motor Displacement Pump Platen Remote DataTrak (single ram systems) or Display Module (tandem systems) Integrated Air Controls (see FIG.
Component Identification S20 3 in. Single Post and D60 3 in. Dual Post Model CM9HLB Shown Model CM2MRY Shown Lift Location H B (Note: Do not use motor lift ring to lift entire system.) Lift Location X B X G A G F R Lift Location F C R C K K J J P D A D r_255648_313527_5a r_255648_313527_6a FIG. 2 Key: A B C D F G H J K P R S T U Ram Assembly Air Motor Displacement Pump Platen Remote DataTrak (single ram systems) or Display Module (tandem systems) Integrated Air Controls (see FIG.
Component Identification Integrated Air Control Module D200, D200s, D60, and S20 Models Integrated Air Line Accessories See FIG. 1. The integrated air controls include: • Main air slider valve (BA): turns air on and off to the system. When closed, the valve relieves pressure downstream. • Ram air regulator (BB): controls ram up and down pressure and blowoff pressure. • Ram director valve (BC): controls ram direction.
Component Identification L20c 2in. Elevator CM7B1G Model Shown BA BB Lift Location BF R P BC BD J r_257302_312376_1e FIG.
Component Identification L20c 2 in. Air Controls • Air motor regulator (DA): Controls air pressure to motor. • Blowoff button (DB): turns air on and off to push the platen out of an empty drum. • Air motor shutoff valve (DC): turns air on and off to the air motor. • Elevator director valve (DD): controls elevator direction. DA DB DD DC r_257302_312376_2e FIG.
Component Identification Platen Component Identification Model 255664, 200 liter (55 gallon) EK EA EL EM EH EJ EB Model 257727, 20 liter (5 gallon) EP TI10518A EK EA EH EM EG EB EN r_255648_313527_7a FIG.
Before Beginning Repair Before Beginning Repair Grounding Pressure Relief Procedure The equipment must be grounded. Grounding reduces the risk of static and electric shock by providing an escape wire for the electrical current due to static build up or in the event of a short circuit. Pump: use a ground wire and clamp. Loosen grounding lug locknut and washer. Insert one end of a 1.5 mm2 (12 ga) minimum ground wire into the slot in lug and tighten the locknut securely.
Maintenance Procedures Flush Before Using Equipment The pump was tested with lightweight oil, which is left in the fluid passages to protect parts. To avoid contaminating your fluid with oil, flush the pump with a compatible solvent before use. See your pump manual for flushing directions.
Maintenance Procedures Use platen with straight sided pail 1. Ensure large diameter of spacer (EG) is facing down. Work spacer (EG) up over the platen by hand completely above the flange of the platen. See FIG. 12. 2. Working from the top, use screwdriver to position spacer (EG) between flange and wipers (EB). See FIG. 13. b. Remove eight nuts (459) that hold wiper assembly to platen casting (451) and remove wiper assembly. c.
Maintenance Procedures Reassemble 20, 30, and 60 Liter Wiper Assemblies c. 1. Assemble wiper assembly. a. For single wiper assemblies: Place bottom plate (455) on flat surface. Place wiper support (454), wiper (453), spacer (452), and top plate (457) on bottom plate (455). b. For single wiper assemblies with SST platens: Place bottom plate (455) on flat surface. Place wiper support (454), wiper (453), flowered wiper support (460), PTFE spacer (452), and top plate (457) on bottom plate (455).
Maintenance Procedures Remove 30 and 55 Gallon Platen Wipers 1. To replace worn or damaged wipers (EB), raise platen up out of drum. Remove drum from base. Wipe fluid off of platen. 2. Cut top and bottom wipers with knife and remove from platen. See FIG. 15. EB TI10613A FIG. 15 Reinstall 30 and 55 Gallon Platen Wipers 1. Using a wooden or plastic tool to prevent damage to the wiper (EB), clean all material from seal grooves. 2. Working from the bottom, angle one wiper (EB) over back of platen. See FIG.
Troubleshooting Troubleshooting Check all possible problems before disassembling the ram, pump, or platen. Refer to Supply Unit Operation manual 313526 for descriptions of DataTrak diagnostic codes. Refer to Check-Mate Pump Packages manual 312376 for pump troubleshooting. Ram Problem Ram will not raise or lower. Cause Solution Closed air valve or clogged air line. Open, clear. Not enough air pressure. Increase. Worn or damaged piston. Replace. See Supply Unit Repair on page 30.
Repair Repair Disconnect Pump from Platen The pump is mounted to the platens by mounting kit 255392 or 257630. See the Repair Kits on page 64. 30 and 55 Gallon Platen 1. Remove four hex screws (426), four clamps (427), and washers (425). 20, 30, and 60 Liter Platen 1. Loosen two 5/16 in. screws (462) from platen. 2. Carefully pull pump away to prevent damage to pump inlet. If using a pump with intake adapter, remove screws (472), adapter (471), and o-rings (473, 463) from pump inlet.
Repair Connect Platen Remove Displacement Pump 30 and 55 Gallon Platen 1. Place o-ring (428) from mounting kit 255392 on the platen. If attached to plate, place displacement pump onto platen. See FIG. 17. 2. Secure pump’s intake flange to plate with screws (426), washers (425), and clamps (427) included in mounting kit 255392.
Repair b. For NXT 200-1800 with 55 gallon platen: Go to step 3. c. For NXT with smaller platens and all supply units: See procedure for D60 3 in. Dual Post, S20 3 in. Single Post, and L20c 2 in. Supply Units. 3. See Disconnect Pump from Platen on page 22 to disconnect the platen from the displacement pump. 102,103 4. Use two people to lift out the displacement pump. Premier Air Motors: 101 1. Remove nuts and washers (102, 103) from top of platen lift rods (101). See FIG. 20.
Repair Install Displacement Pump 4. Connect air motor: D200 3 in. and D200s 6.5 in. Supply Units NXT Air Motors 1. Insert displacement pump on platen. Follow Connect Platen steps on page 23. 2. See Reconnect Displacement Pump in Check-Mate Pump Packages manual 312376. 3. Reconnect ground wire and air motor harness (units with Remote DataTrak) if they were disconnected. a. For NXT 2200-6500 with 55 gallon platen: Use wrench on nut (105) on top of ram bar to lower air motor onto displacement pump.
Repair Remove Air Motor NXT Air Motors 1. See Disconnect Displacement Pump in Check-Mate Pump Packages manual 312376. 2. Disconnect air hose from air motor. If using a remote DataTrak, detach electrical connections from the air motor. 110 111 r_255648_313527_9a FIG. 24: NXT 200-1800 with 55 Gallon PLaten 3. Disconnect air motor: a. For NXT 2200-6500 with 55 gallon platen (D200 3 in. and D200s 6.5 in. supply units): Loosen nut (105a) below crossbar.
Repair d. For NXT on S20 3 in. supply unit and L20c 2 in. elevator: Remove screws (111) and washers (110) securing motor to mounting bracket. 1c 103, 102 109 113 114 110 111 TI10658A r_255648_313527_10a FIG. 28: Premier Air Motors FIG. 27 4. Using a capable hoist, secure air motor to hoist and remove air motor. Premier Air Motors 1. Remove air hose. 2. See Disconnect Displacement Pump in Check-Mate Pump Packages manual 312376. 3. Remove nuts (103), washers (102), and cross bar (1c). 4.
Repair Install Air Motor D200 3 in. and D200s 6.5 in. Supply Units NXT with 55 gallon platen: 1. For NXT2200-6500: Using a capable hoist, insert tie rods into displacement pump and secure air motor to pump. a. See Reconnect Displacement Pump in Check-Mate Pump Packages manual 312376. b. Install threaded rod (106) through center hole in the crossbar. Install lock washers (104) and nuts (105) onto threaded rod (106), both above and below crossbar.
Repair D60 3 in. Dual Post Supply Unit NXT Air Motors 1. Using a secure hoist, attach motor to mounting plate (109) with screws (111) and washers (110). See FIG. 26 on page 26. 2. See Reconnect Displacement Pump in Check-Mate Pump Packages manual 312376. 3. Connect air hose to motor. If using a remote DataTrak, connect electrical connections to the air motor. See FIG. 24 on page 26. S20 3 in. Single Post Supply Unit and L20c 2 in. Elevator NXT Air Motors 1.
Repair Supply Unit Repair 1e 1h 1j To reduce the risk of serious injury whenever you are instructed to relieve pressure always follow the Pressure Relief Procedure on page 16. Do not use pressurized air to remove the guide sleeve or the piston. 1f 1k 1g D200s 6.5 in. Ram Piston Rods Always service both cylinders at the same time. When you service the lift rod always install new o-rings in the piston rod seal and ram piston. Disassemble Piston Rod Seal 1d TI10784A FIG. 30: 6.5 in. Piston Rod Seal 1.
Repair Disassemble Ram Piston Assemble Ram Piston 1. Relieve pressure. 1. Install new o-rings (1p, 1j) on piston rod (1d) and piston (1r). Lubricate the piston (1r) and o-rings (1p, 1j). Reinstall piston (1r) and lower retaining ring (1n) onto piston rod (1d). Install piston guide band (1q) onto piston (1r). 2. Remove nuts (1a) and lockwashers (1b) holding the tie bar (1c) to the piston rods (1d). See page 38. 3. Remove nuts (103, 105) and washers (102, 104). See parts illustration on page 42. 4.
Repair D200, D60, and S20 3 in. Ram Piston Rods Always service both cylinders at the same time. When you service the piston rod always install new o-rings in the piston rod seal and ram piston. Disassemble Piston Rod Seal and Bearing 1. Relieve pressure. 5. Inspect parts for wear or damage. Replace as necessary. Do not reinstall end cap assembly if the ram piston (202e, 802e) needs to be removed from the piston rod. See the next page for ram piston repair instructions. 2.
Repair Assemble Piston Rod Seal and Bearing See FIG. 32 on page 32. 1. For S20 3 in. Ram: Lubricate seal (802d) and spacer (802p) and install in bearing (802j). Remove nut (202f, 802f), washer (202g, 802g), piston (202e, 802e), outer o-ring (202c, 802c), and inner o-ring (202h, 802h). 3. Inspect parts for wear or damage. Replace as necessary. a. Align groove on bearing with pin (802b) and install bearing (802j) into end cap (802a). Lubricate o-ring (802c) and end cap (802a). b.
Repair L20c 2 in. Elevator 522 Disassemble Piston Rod Seal, Bearing, and Piston 521 1. Remove air motor. See Remove Air Motor on page 26. 2. Remove nut (522), lock washer (521), handle (520), washer (519), and air motor mounting bracket (518) from end cap (516). 519 520 518 3. Remove retaining ring (510). 4. Remove cylinder end cap (516). Remove o-ring (513) and replace if necessary. 5. Remove screw (514) from inside cylinder (515) and lift cylinder assembly off of elevator cart (501). 510 6.
Repair Power Supply 6. Remove protective earthing conductor from the PE terminal marked . 7. Remove screws (159) and 24 Vdc power supply module (154) from power supply mounting bracket (151. See parts illustration on page 53. Remove 24 Vdc Module 8. Remove screws (155) and power switch (157) from power supply mounting bracket (151). 1. Turn external 24 Vdc power source off. 2. Remove shrouding covers. See DataTrak Kit parts illustrations on page 61-62. 3.
Repair 6. Attach 24 V Class 2 power supply to terminals on the power switch: +24 Vdc to terminal 2 (+) and 24 Vdc return to terminal 5 (-). See FIG. 36. Attach protective earthing (PE) conductor to terminal marked . See FIG. 37. The 24 Vdc power supply must be capable of supplying at least 1.0 Amp and have supply current protection rated at no more than 2.5 Amps. 8. Inspect all parts for wear or damage. Replace as needed. Replace 100-240 Vac Fuses 1. Turn power supply OFF and Disconnect power. 2.
Parts Parts Use this table to identify which pump mounting kit and platen are compatible with each air motor and supply system. See page 39 for relief valve for your pump package. Pump Mounting Kit Supply System Air Motor Size Kit Gallons (liters) Pump Mounting Kit Page Platens Page NXT200 NXT400 257627 55 (200) pg. 42 pg. 55 257628 D200 3 in. Dual Post (see page 40) Platens NXT700 NXT1200 NXT1800 257625 257626 5 (20), 8 (30), 16 (60) 30 (115) 55 (200) 5 (20), 8 (30), 16 (60) 30 (115) pg.
Parts D200s 6.5 in. Supply Units Model 255688 Shown 5 6 See page 53 for power supply illustration.
Parts D200s 6.5 in. Supply Units, 255688 Ref No. 1 1a 1b 1c 1d 1e* 1f* 1g 1h* 1j* 1k* 1n* 1p* 1q* 1r 1s✖ 1u 1v 1w 1x 1y▲ 1z✖ 2✖ Part No. Description RAM, 6.5 in. (includes 1a - 1z) 113939 NUT, jam, hex 113993 WASHER, lock, helical 15M538 BEAM, tie C32401 ROD C03043 RING, snap C31001 WIPER, rod 617414 SLEEVE, guide, 6-1/2 in.
Parts D200 3 in. Supply Units Model 255648 Shown 211 212 See page 53 for power supply illustration.
Parts D200 3 in. Supply Units, 255648 Ref No. Part No. Description Qty 201 RAM, 3 in. 1 202 PISTON, assembly 3 in.
Parts D200s and D200 Pump Mounts for 55 Gallon (200 Liter) Platen Kits - 257625 and 257627 Kits - 255315, 255305, and 256235 Note: See page 37 for kit configuration table. Note: See page 37 for kit configuration table. 105 104 103 102 104 103, 105 105 102, 104 120 101 101 119 118 r_255648_313527_12a 106 107 108 109 110 111 117 TI10771A Ref.
Parts D200s and D200 Pump Mounts for 5 Gallon (20 Liter), 8 Gallon (30 Liter), 16 Gallon (60 Liter), and 30 Gallon (115 Liter) Platens Kits - 255316, 255317, 255308, 255309 Note: See page 37 for kit configuration table. 103 102 116 117 101 102 103 109 110 111 Ref.
Parts Pump Mount 255306 (Premier motors on 6.5 in. supply units only) Kits - 257626 and 257628 Note: See page 37 for kit configuration table. Note: See page 37 for kit configuration table. 103 102 115 116 101 117 102 103 118 103 112 102 109 102 109 120 102 114, 113 103 119 103 110 111 101 r_255648_313527_13a Ref. Part. 101 257726 102 101533 103 101535 109 110 100133 111 117 114128 118 100896 119 120 061513 121✖ 122✖ 123✖ ✖ Not shown.
Parts D60 3 in. Dual Post Supply Unit Model 257621 Shown 211 See page 53 for power supply illustration.
Parts D60 3 in. Supply Units, 257621 Ref. 202 Part 202a* 202b* 107092 202c* 202d* 202e* 183943 202f* 202g* 202h* 202j* 202k* 202m* 302n* 15V697 203* 127510 301 209 211 101682 212 100016 213 255650 215 46 101689 Description PISTON, ram, subassembly; includes 202a-202m BEARING, ram end cap PIN, spring, straight O-RING O-RING PISTON NUT, jam WASHER, split O-RING BEARING, ram end cap RETAINER, retaining ring SPRING, compression ROD, piston, ram RING, retaining, 3.
Parts D60 Pump Mounts 257623 and 257624 for 5 Gallon (20 Liter), 8 Gallon (30 Liter), and 16 Gallon (60 Liter) Platens Note: See page 37 for kit configuration table. 383 382 381 386 384 387 385 r_255648_313527_15a Ref. Part 381 ‡ ✿ 382 101533 383 101535 384 100133 385 C38372 386 105281 387 C12034 388✖ 389✖ 390✖ 391✖ 160327 Description BRACKET, shelf, NXT2200 BRACKET, shelf, NXT3400 and NXT6500 WASHER, spring lock NUT, hex WASHER, lock SCREW, cap, hex head FITTING, 3.
Parts S20 3 In. Single Post Ram S20 Single Supply Unit Cart Shown See page 53 for power supply illustration.
Parts S20 Single Supply Unit, 257620 Ref. 801 802 Part 802a 802b 802c 802d 802e 802f 802g 802h 802j 15V032 15U979 160258 15U189 183943 101535 101533 156401 15U546 257619 Description RAM PISTON, S20 ram, subassembly; includes 802a-802p BEARING, rod top PIN, spring, straight O-RING SEAL, d-shaped u cup PISTON NUT, hex WASHER, spring lock O-RING BEARING, ram end cap max flat Qty . 1 1 1 3 2 1 1 1 1 1 1 Ref. 802k Part Description 15F453 RETAINER, retaining ring 1.
Parts S20 3 In. Single Post Ram Mounting Kit 257664 - For NXT200 and NXT400 NXT700, NXT1200, and NXT 1800 257666 - For NXT2200 and NXT3400 257612 - Air controls sold separately for S20 ram. Includes 2 gauges (113911) and 2 labels (15V954). Motor mount bracket for 257666 257664 Shown 857 851 858 851 854 868 859 855 856 860 852 862 r_255648_313527_19a Ref.
Parts L20c 2 In. Elevator 522 521 520 L20c Cart Kit, 257638 519 L20c Cylinder Kit, 257611 524 518 510 506 517 516 506 514 507 512 511 505 510 513 509 508 501 503 515 504 502 r_255648_313527_21a Ref.
Parts ★ Included in kit 257611. Air Control Kit- L20c 2 In. Elevator 257613 - For NXT200, NXT400, NXT700, NXT1200, and NXT1800 557 551 553 552 556 r_255648_313527_23a r_255648_313527_22a Ref. Part 551 552 553 554✖ 555✖ 556 557 Description PANEL, air control; see manual 312374 SCREW, cap, socket head WASHER, lock TUBE, nylon, rnd; 52 in. TUBE, nylon, 1/2 OD X 3/8 ID; 25 in. SCREW, cap, socket hd ELBOW, male, swivel ELBOW, male, swivel, 1/2 npt x 1/2 tube Qty .
Parts Power Supply - D200s, D200, D60, and S20 3 in.
Parts 24 Vdc and 100-240 Power Supply Parts (24 Vdc) Ref. No. 151 Description ENCLOSURE, power supply assy 152 WASHER, lock 153 SCREW, cap, sch 154 MODULE, assembly, 24V 154a POWER SUPPLY, 100-240 Vac 155 SCREW, mach, pan head 156 SCREW, self-tapping 157 SWITCH, power, 24 Vdc 157a SWITCH, power, 120V 158 COVER, switch mount 159 SCREW, countersunk, 6-32 x 0.38 160 COVER, power 161 GROMMET 162▲ LABEL, caution 163 CABLE, power, female,.8M 164 WASHER, lock 165 FUSE, 250V / 1.
Parts 30 and 55 Gallon Platen 115 Liter (30 Gallon) Platen, Model 255661 200 Liter (55 Gallon) Platen, 255662, 255663, and 255664 404 417 429 416 411 403 *426 405 *427 *428 416 403 417 414 421 406 414 420 408 408 410 TI10530A ti20583a 115 Liter (30 Gallon) Platen Parts Ref. No. 403 404 405 406 408 410 411 414 416 417 420 429 Part No.
Parts 20 Liter (5 Gallon), 30 Liter (8 Gallon), and 60 Liter (16 Gallon) Platens Single Wiper with SST Platen Double Wiper Platen 470 461 461 Single Wiper Platen 469 459 470 469 462 461 459 462 451 465 456 459 465 464 462 456 459 457 459 464 464 451 451 453 465 457 456 459 452 452 457 452 460 453 453 453 454 454 454 455 455 455 r_255648_313527_26a r_255648_313527_25a r_255648_313527_34a 56 313527V
Parts Platen Descriptions Platen Platen Size 257727✿ 20 Liter (see page 58) Platen Material Seal Material Wiper Assembly Kit CS Nitrile 257639 CS PolyUrethane 257640 257729✿ SST PTFE-coated Nitrile 257641 257730❄ CS Nitrile 257642 257731❄ CS PolyUrethane 257643 CS Nitrile 257644 CS PolyUrethane 257645 257734✿ SST PTFE-coated Nitrile 257646 257735❄ CS Nitrile 257647 257728✿ 257732✿ 257733✿ 30 Liter (see page 58) 257736❄ CS PolyUrethane 257648 CS Nitrile 257649
Parts Common Parts Ref. 456 459 461 463 465 The parts listed below are common among all 20, 30, and 60 liter platens. Parts that vary are found in the tables on page 58-60. Part 121829 113504 257697 109482 C20350 Description O-RING NUT, keps, hex hd HANDLE, bleed, sst O-RING; see page 60 ELBOW, 90°; 1/4 OD x 1/4 npt1 Qty . 1 12 1 1 Varying Parts - 20 Liter (5 Gallon) Platens The following table indicates which parts (according to reference number) are included with each platen. Reference Numbers Ref.
Parts Parts designated n/a are not available separately. ‡ See page 57 for wiper assembly kits.
Parts Varying Parts - 60 Liter (16 Gallon) Platens The following tables indicates which parts (according to reference number) are included with each platen. Reference Numbers Ref.
Accessories Accessories D200s, D200, and D60 DataTrak Accessory Kits D200s Supply Units, 255705 (100-240 Vac) and 255758 (24 Vdc) D200 and D60 Supply Units, 255757 (24 Vdc) and 255704 (100-240 Vac) 616 613 610 617 618 606 614 611 601, 602 608 667 669 619 607 601 602 See Power Supplies illustration on page 53. r_255648_313527_28a Ref. 601 602 603 604 605 609 610 611 612 613 614 615 616 Qty Part Description .
Accessories See page 63 for varied parts table. S20 3 in. Supply Unit DataTrak Accessory Kit, 257636 and 257635 663 See Power Supplies illustration on page 53. 667 664 651 652, 653 659 658 657 661 654 656 Ref. 651 652 653 654 655 656 657 658 659 661 662 663 664 665✖ 666✖ 667▲ 668✖ 62 Part 255415 257657 122487 189285 Description BRACKET, datatrak WASHER, lock SCREW, cap, socket head KNOB, display adj. WASHER, plain SCREW, shcs, 1/4-20UNC x 4.
Accessories Varied Parts for DataTrak Accessory Kits D200s, D200, and D60 Supply Units 24 Vdc Ref. No. 606 607 608 151* 154a* 157a* 155* 160* 165* 154* 160* 163* 156* * Description COVER, shroud front COVER, shroud rear BRACKET, light tower BRACKET, power supply POWER SUPPLY, 100-240 Vac SWITCH, power, 100-240 Vac SCREW, machine, pan hd COVER, power FUSE, 250V/1.2A MODULE, assembly, 24V COVER, switch mount CABLE, pwr, female, 0.
Accessories Two-Button Interlock Air Control Kit Check-Mate Displacement Pump Kits See 312374 for information. Displacement Pump Size 60cc 100cc 200cc 250cc 500cc Supply Unit Part D200 255719 D200s 255720 D60 257615 Drum Roller Kits for D200 and D200S Supply Units, 255627 See 312492 for more information.
Dimensions Dimensions D200 S20 S30 A (ram up) A (ram up) B (ram down) B (ram down) ti10429a D E C E C F F D r_255648_313527_5a L20c D60 A (ram up) A (ram up) B (ram down) B (ram down) D C D F E F 313527V r_255648_313527_6a r_257302_312376_1e 65
Dimensions S20 (NXT) S30 WL D A (ram up) B (ram down) C E D F Dimensions Ram Model A in. (mm) B in. (mm) C in. (mm) L20c 69 (1752.6) 44 (1117.6) S20 (NXT) 84 (2133.6) 59 (1498.6) 16 (406.4) 19 (482.6) 11 (279.4) 17 (431.8) S20 59.3 (1506) 35.8 (909) 16 (406.4) 19 (482.6) 11 (279.4) 17 (431.8) S20c 90 (2286) 65 (1651) D60 89 (2260.6) 59 (1498.6) 14 (355.6) 18 (457.2) 24 (609.6) 28 (711.2) D200 102.3 (2599) 64.8 (1646) 21.0 (533) 25.0 (635) 38.0 (965) 42.
Technical Data Technical Data Max air input pressure (supply system) / Air inlet size L20c - 2 in. elevator, 5 gal. (20 L) . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar) / 1/2 npsm(f) S20 - 3 in. single post, 5 gal. (20 L) . . . . . . . . . . . . . . 125 psi (0.9 MPa, 9 bar) / 1/2 npt(f) D60 - 3 in. dual post, 16 gal. (60 L), 5 gal. (20 L), 30 gal. (115 L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 psi (1.0 MPa, 10 bar) / 3/4 npt(f) D200 - 3 in. dual post, 55 gal.
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
