User's Manual

ManualsBrandsGraco ManualsDo-It-Yourself tools332073B

332073B

Instructions - Parts

XM PFP

Hot Water Flush Kit

For flushing the XM PFP system with hot water. For professional use only.

Not approved for use in explosive atmospheres or hazardous locations.

Part No. 16T859

Six Gallon Electric Water Heater Kit

100 psi (0.7 MPa, 7 bar) Maximum Inlet Pressure to Regulator

180°F (82°C) Maximum Outlet Fluid Temperature

Contents

Component Identification ....................2

Installation ................................3

Optional Location 1 .......................3

Optional Location 2 .......................4

Priming the Heater .........................5

OtherInstructions ..........................5

Parts .....................................6

16T859 Kit ..............................6

TechnicalData .............................9

Graco Standard Warranty ...................10

Important Safety Instructions

Read all warnings and instructions in this manual, the

XM PFP Operation manual 3A2776, and the Hatco

C-5 instruction manual. Save all instructions.

ti20139a

Summary of content (10 pages)

PAGE 1
Instructions - Parts XM PFP Hot Water Flush Kit 332073B EN For flushing the XM PFP system with hot water. For professional use only. Not approved for use in explosive atmospheres or hazardous locations. Part No. 16T859 Six Gallon Electric Water Heater Kit 100 psi (0.
PAGE 2
Component Identification Component Identification F D E ti20139a G C B A ti20152a H FIG.
PAGE 3
Installation Installation 1. Use four bolts and washers (20, 14) to install the bracket (13) onto the system frame. 2. Use four bolts and washers (19, 15) to install heater (1) onto bracket. The equipment must be grounded to reduce the risk of static sparking and electric shock. Electric or static sparking can cause fumes to ignite or explode. Improper grounding can cause electric shock. Grounding provides an escape wire for the electric current. 3. Connect water supply hose to heater inlet (A).
PAGE 4
Installation Optional Location 2 4. Connect water supply hose to heater inlet (A). Connect hose from heater outlet (G) to PFP solvent flush pump bottom inlet. See FIG. 1 on page 2 and FIG. 3 on page 4. NOTICE 1. Use four bolts and washers (20, 14) to connect the three bracket pieces (13, 22, 23). To prevent burning out the heater element, never turn on the heater without it completely filled with water. 2. Use four bolts and washers (21, 19) to install the bracket assembly onto system frame. 5.
PAGE 5
Priming the Heater Priming the Heater BURN HAZARD Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe burns: • Do not touch hot fluid or equipment. NOTICE To prevent burning out the heater element, never turn on the heater without it completely filled with water. 1. With the heater ON/OFF toggle switch (H) OFF, turn on the water supply. 2. Adjust the fluid pressure regulator (B) to 20 psi (0.14 MPa, 1.4 bar). 3.
PAGE 6
Parts Parts 16T859 Kit 1 1b 18 11 16 1d 5 37 25 35 1d 3 27 35 5 4 28 26 36 2 29 10 1c 6 7 8 9 19 ti20140a 21 22 23 21, 19 13 19 15 14 20 NOTE: Use sealant on all pipe threads.
PAGE 7
Parts Ref 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24▲ 25▲ 26 27 28 29 35 36 37 Part 16T869 166466 113445 194048 107219 166590 157191 16T886 115099 119992 16T619 16T751 100018 C19138 --16T891 121603 115625 112395 121488 256254 256256 189285 189930 H43806 156589 100505 156849 156172 295847 125548 Description Qty HEATER, Hatco C-5 1 FITTING, tee, pipe, female 1 FITTING, elbow, street 1 FITTING, nipple, reducing 1 BUSHING 2 FITTING, elbow, street 1 FITTING, adapter (1/2 npt x 3/4 npt) 1 ADAP
PAGE 8
Parts 8 332073B
PAGE 9
Technical Data Technical Data See the Hatco® C-5 instruction manual for full technical data. PFP Hot Water Flush Kit Maximum Water Inlet Pressure to Regulator Maximum Regulated Pressure Maximum Outlet Fluid Temperature Supply Voltage Power Tank Size Inlet Fitting Wetted Parts 332073B US 100 psi 20 psi 180°F 220-250 Volts AC, 1 phase 5000 Watts 6 gallon 3/4 NHR Garden Hose Metric 7 MPa, 7 bar 140 kPa, 1.4 bar 82°C 22.
PAGE 10
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.