User's Manual

10
Ordering Information
Pro Xp Air-Assist
Part Number Power Supply kV Recommended Coating Type Display Type
H85T10 85 Standard Standard
H85M10 85 Standard Smart
H60T10 60 Standard Standard
H60M10 60 Standard Smart
H60T18 60 Waterborne Standard
H60M18 60 Waterborne Smart
All gun models include AEM or AEF tip of choice.
Air-Assist Gun Models
AEF Fine Finish Pre-Orifice Spray Tips
AEM Spray Tips
Recommended for high finish quality applications at low and medium pressures. AEF tips have a pre-orifice that assists in atomizing sheer thinning materials.
Order desired tip, Part No. AEFxxx, where xxx = 3-digit number from the matrix below.
Orifice Size
inch (mm)
Fluid Output
fl oz/min (l/min)
Maximum Pattern Width at 12 inches (305 mm)
inches (mm)
at 600 psi
(41 bar, 4.1 MPa)
at 1000 psi
(70 bar, 7.0 MPa)
6-8
(150-200)
8-10
(200-250)
10-12
(250-300)
12-14
(300-350)
14-16
(350-400)
16-18
(400-450)
Spray Tip
† 0.010 (0.254) 9.5 (0.28) 12.5 (0.37) 310 410 510 610 710 –
0.012 (0.305) 12.0 (0.35) 16.0 (0.47) 312 412 512 612 712 812
0.014 (0.356) 16.0 (0.47) 21.0 (0.62) 314 414 514 614 714 814
0.016 (0.406) 20.0 (0.59) 26.5 (0.78) – 416 516 616 716 –
* Tips are tested in water.
Fluid output (Q) at other pressures (P) can be calculated by this formula: Q = (0.041) (QT)
√P where QT = fluid output (fl oz/min) at 600 psi from the above
table for the selected orifice size.
† These tip sizes include a 150 mesh filter.
Recommended for high finish quality applications at low and medium pressures.
Order desired tip, Part No. AEMxxx, where xxx = 3-digit number from the matrix below.
Orifice Size
inch (mm)
Fluid Output
fl oz/min (l/min)
Maximum Pattern Width at 12 inches (305 mm)
inches (mm)
at 600 psi
(41 bar,
4.1 MPa)
at 1000 psi
(70 bar,
7.0 MPa)
2-4
(50-100)
4-6
(100-150)
6-8
(150-200)
8-10
(200-250)
10-12
(250-300)
12-14
(300-350)
14-16
(350-400)
16-18
(400-450)
Spray Tip
† 0.007 (0.178) 4.0 (0.1) 5.2 (0.15) 107 207 307 – – – – –
† 0.009 (0.229) 7.0 (0.2) 9.1 (0.27) – 209 309 409 509 609 –
† 0.011 (0.279) 10.0 (0.3) 13.0 (0.4) – 211 311 411 511 611 711 –
0.013 (0.330) 13.0 (0.4) 16.9 (0.5) – 213 313 413 513 613 713 813
0.015 (0.381) 17.0 (0.5) 22.0 (0.7) – 215 315 415 515 615 715 815
0.017 (0.432) 22.0 (0.7) 28.5 (0.85) – 217 317 417 517 617 717 –
0.019 (0.483) 28.0 (0.8) 36.3 (1.09) – – 319 419 519 619 719 –
0.021 (0.533) 35.0 (1.0) 45.4 (1.36) – – – 421 521 621 721 821
0.023 (0.584) 40.0 (1.2) 51.9 (1.56) – – – 423 523 623 723 823
0.025 (0.635) 50.0 (1.5) 64.8 (1.94) – – – 425 525 625 725 825
0.029 (0.736) 68.0 (1.9) 88.2 (2.65) – – – – – – – 829
0.031 (0.787) 78.0 (2.2) 101.1 (3.03) – – – 431 – 631 – 831
0.033 (0.838) 88.0 (2.5) 114.1 (3.42) – – – – – – – 833
0.037 (0.939) 108.0 (3.1) 140.0 (4.20) – – – – – – 737
0.039 (0.990) 118.0 (3.4) 153.0 (4.59) – – – – 539 – – –
* Tips are tested in water.
Fluid output (Q) at other pressures (P) can be calculated by this formula: Q = (0.041) (QT)
√P where QT = fluid output (fl oz/min) at 600 psi from the above table
for the selected orifice size.
† These tip sizes include a 150 mesh filter.