User's Manual

ManualsBrandsGraco ManualsAutomatic Lubrication SystemsGraco 3A0534F G3 Reservoir and O-Ring Replacment Kit

Instructions

G3 Reservoir and O-Ring

Replacement Kit

Instructions for replacing G3 reservoir and o-rings. For professional use only.

Part No.:

571042, 571069, 571179 - 2 Liter

models

571182, 571183 - 4 Liter models

Kit Parts 571179, 571182

Kit Parts 571042, 571069, 571183

Ref. Description Qty

1 RESERVOIR 1

2 CAP, oil, fill 1

3 LABEL 1

4O-RING 1

5 O-RING, square 1

Important Safety Instructions

Read all warnings and instructions in this

manual and the G3 Pump Instruction manual

included with your unit. Save these instruc-

tions.

Ref. Description Qty

1O-RING 1

2 RESERVOIR 1

3 LABEL 1

4 O-RING, square 1

3A0534F

Summary of content (6 pages)

PAGE 1
Instructions G3 Reservoir and O-Ring Replacement Kit 3A0534F EN Instructions for replacing G3 reservoir and o-rings. For professional use only. Part No.: 571042, 571069, 571179 - 2 Liter models 571182, 571183 - 4 Liter models Important Safety Instructions Read all warnings and instructions in this manual and the G3 Pump Instruction manual included with your unit. Save these instructions. 2 2 1 3 3 4 1 1 5 4 Kit Parts 571042, 571069, 571183 Kit Parts 571179, 571182 Ref.
PAGE 2
Instructions Instructions 3. Use a strap wrench around reservoir to turn reservoir 1/4 turn counter-clockwise (FIG. 2). Pressure Relief SKIN INJECTION HAZARD High-pressure fluid from dispense device, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. Follow Pressure Relief Procedure in this manual, when you stop dispensing and before cleaning, checking, or servicing equipment.
PAGE 3
Instructions 3. Be sure parts remaining in reservoir were removed to reuse them for reassembly. 4. Examine follower plate seal referenced in Step 1 for wear or damage. If it is damaged, it must be replaced. Part No. 278139 is available from Graco. Contact customer service to order this part or your local Graco distributor.
PAGE 4
Instructions Reassembly Lower O-Ring Installation d 1. Coat new o-ring (1) with grease (user supplied) and install o-ring in bottom groove of ricer plate (b). b 1 FIG. 9 4. Complete installation following instructions for Top O-ring and Reservoir installation, page 4. Top O-ring Installation 1. Coat new o-ring (1) with grease (user supplied). 2. Install o-ring in groove of ricer plate (b) (FIG. 10). FIG. 7 1 2. Replace ricer plate (b), aligning circular sections with the round bosses in the base.
PAGE 5
Instructions Reservoir Installation plate) as shown in FIG. 11. 1. Install new reservoir (2) with vent (g) facing toward the rear left (h) of the G3 base. See FIG. 12 for correct orientation of these parts to ensure proper installation. R g 2 S f FP FPS c h FIG. 11 3. Install spring (S) into spring pocket (f). FIG. 12 4. Install Rod (R) into reservoir (2). 2. Position strap wrench over reservoir and use it to turn reservoir 1/4 turn clockwise till reservoir will not turn any farther (FIG. 12).
PAGE 6
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. For patent information, see www.graco.com/patents Original instructions. This manual contains English. MM 3A0534 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441 Copyright 2010, Graco Inc. is registered to ISO 9001 www.