Repair/Parts ® ProMix 2KE 3A0870L Plural Component Proportioner EN Self-contained, electronic plural component paint proportioner. For professional use only. Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See pages 3 and 4 for model information, including maximum working pressure and approvals. For patent information, see www.graco.
Contents Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Non-Hazardous Location Models . . . . . . . . . . . . . . 3 Hazardous Location Models . . . . . . . . . . . . . . . . . . 4 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Important Two-Component Material Information . 8 Isocyanate Conditions . . . . . . . . . . . . . . . . . . . . . 8 Material Self-ignition . . . . . . . . . . . . . . . . . . . . . . 8 Keep Components A and B Separate . . . . . . .
Related Manuals Related Manuals Manual 3A0868 3A0869 313599 308778 312781 312782 312784 312792 312793 312796 Description ProMix 2KE, Pump-Based, Operation ProMix 2KE, Meter-Based, Operation Coriolis Meter G3000 Flow Meter Fluid Mix Manifold Dosing Valve Gun Flush Box Kit 15V826 Merkur Displacement Pump Merkur Bellows Displacement Pump NXT Air Motor Manual 406714 406823 3A1244 3A1323 3A1324 3A1325 3A1332 3A1333 313542 Description Rebuild Kit for High Pressure Dispense Valve Dispense Valve Seat Kits Graco
Hazardous Location Models Hazardous Location Models ProMix 2KE systems are not approved for use in hazardous locations unless the base model, all accessories, all kits, and all wiring meet local, state, and national codes. Approved for Hazardous Location Class 1, Div 1, Group D (North America); Class 1, Zones 1 and 2 (Europe) Maximum Working Pressure USB psi (MPa, bar) Module Approvals* Part No. Series Description Pump Systems 24F102 A 3:1, Merkur, A and B 300 (2.
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
Warnings WARNING INTRINSIC SAFETY Intrinsically safe equipment that is installed improperly or connected to non-intrinsically safe equipment will create a hazardous condition and can cause fire, explosion, or electric shock. Follow local regulations and the following safety requirements. • Only models with model numbers 24F084-24F087 and 24F102-24F115, utilizing the air-driven alternator, are approved for installation in a Hazardous (explosive atmosphere) Location. See Hazardous Location Models, page 4.
Warnings WARNING EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals. • Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings.
Important Two-Component Material Information Important Two-Component Material Information Isocyanate Conditions Spraying or dispensing materials containing isocyanates creates potentially harmful mists, vapors, and atomized particulates. Read material manufacturer’s warnings and material MSDS to know specific hazards and precautions related to isocyanates. Prevent inhalation of isocyanate mists, vapors, and atomized particulates by providing sufficient ventilation in the work area.
Pressure Relief Procedure Pressure Relief Procedure Meter Systems To reduce the risk of skin injection, relieve pressure when you stop spraying, before changing spray tips, and before cleaning, checking, or servicing equipment. 1. Press on Run Mix Spray (Screen 2) or from any screen to put the system in Standby. 2. Shut off the A1 (A2 and A3, if using multiple colors) and B fluid supply pumps/pressure pots. NOTE: The following procedure relieves all fluid and air pressure in the ProMix 2KE system. 3.
Purging Purging Pump Systems There are 2 pump purging procedures in this manual: • • Purging Mixed Material Purging Fluid Supply System Use the criteria listed for each procedure to determine which procedure to use. There are times when you only want to purge the fluid manifold, such as: end of potlife breaks in spraying that exceed the potlife overnight shutdown before servicing the fluid manifold assembly, hose or gun. 1.
Purging 5. Disconnect the component A and B fluid supplies at the pump inlets, and connect solvent supply lines. 6. Adjust the solvent fluid supply pressure. Use the lowest possible pressure to avoid splashing. 7. Remove the Control Box cover to access the solenoid valves. See FIG. 1, page 12. 8. Purge as follows: • Purge component A side. See FIG. 1, page 12. Press the manual override on the Dose Valve A solenoid valve and trigger the gun into a grounded metal pail. Purge component B side.
Purging Manual Overrides Solvent Valve A Solenoid Dose Valve A1 Solenoid Solvent Valve B Solenoid Dose Valve A3 Solenoid Location Dose Valve B Solenoid Gun Flush Box Solenoid Location ti15730a Dose Valve A2 Solenoid Location FIG. 1. Solenoid Valves in Control Box Shutdown 1. Follow Purging procedure for your system, page 10 or 11. 2. Close main air shutoff valve on air supply line and on ProMix 2KE. 3. Non-IS Systems: Shut off ProMix 2KE power (0 position).
Service Service Before Servicing 4. Remove and replace element (206a, 209a). 5. Screw filter bowl (B) on securely. Install cover (A). Pump System • To avoid electric shock, turn off power before servicing. • Servicing the Control Box exposes you to high voltage. Shut off power at main circuit breaker before opening enclosure. 209 • All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.
Service Replace Solenoids The system has a minimum of 4 solenoids. If you have a 3-color system or a gun flush box, you have additional (optional) solenoids for each. To replace the solenoid module: 1. Follow Before Servicing, page 13. Disconnect main power. 2. Open Control Box. 3. Disconnect all solenoid wires (N) from harnesses (320). To replace a single solenoid: 1. Follow Before Servicing, page 13. Disconnect main power.
Service Replace the Power Supply All electrical wiring must be completed by a qualified electrician and comply with all local codes and regulations. Wall Power Supply and Filter 1. Follow Before Servicing, page 13. Disconnect main power. 10. Connect the power supply wire harness (411/PS) to the switch (402), as shown. See also Electrical Schematic. Connect the PS ground wire to the ground terminal (T) of the advanced fluid control module. 11. See FIG. 5.
Service 402 2: PS(L) 1: PS(N) 1A: LF(N) 1A: LF(N) 401a 302 T LF(L) LF(N) 405 403 401 PS(GND) PS(L) PS(N) 407 ti16454a 406 FIG. 8.
Service Alternator Power Supply and Turbine 5. Disconnect air regulator line and exhaust air line from alternator module. 1. Follow Before Servicing, page 13. Disconnect main air. 6. Remove four screws (509) from mounting to remove alternator from control box. 2. Open Control Box. 3. See FIG. 9. Disconnect output power cable connections from alternator module (501). Disconnect ground lead (G) from control box ground terminal (T). 4.
Service Replace Alternator Regulator 1. Follow Before Servicing, page 13. Disconnect main air. Replace Advanced Fluid Control Module (AFCM) 2. Open Control Box. 3. Disconnect supply air line from regulator assembly (505). 4. Loosen air regulator swivel fittings (506) and remove from solenoid module. 1. Follow Before Servicing, page 13. Disconnect main power. 2. Open Control Box. 5. Repair or replace alternator regulator parts as necessary. See Alternator Power Assembly, page 46, for repair parts.
Service Replace Alarm Replace Display Module 1. Follow Before Servicing, page 13. 1. Follow Before Servicing, page 13. Disconnect main power. 2. The Display Module (63) snaps tightly into the mounting bracket (49). To remove it, lift up on the front of the bracket and, at the same time, pull the Display Module out. 2. Open Control Box. 3. Disconnect the CAN cable (64). 3. Disconnect alarm wires from alarm (311). 4. Replace with a new Display Module. 4.
Service Replace USB Module USB Module 1. Follow Before Servicing, page 13. Disconnect main power. 2. Open Control Box. 3. Non-IS Systems: Disconnect Display Module CAN cable, Advanced Fluid Control Module CAN cable and USB cable from the USB module (340). IS Systems: Disconnect Alternator CAN cable and USB cable from the USB module (340). P4 P3 ti16580a Advanced Fluid Control Module Display Module J8 4. Remove ground screw (343) from top of Control Box for USB module and bracket. 5.
Service 343 349 342 342 341 (X 4) 348 340 345 ti16451a FIG. 16.
Service Pump System Air Controls Replace Pressure Gauge(s) 1. See Remove Air Control Assembly, page 22. See FIG. 18, page 23, for a full diagram of the pump air controls. Remove Air Control Assembly 1. Follow Before Servicing, page 13. 2. See FIG. 17. Disconnect pump air lines, main air line, and solenoid air line. 2. Disconnect air lines to gauges (203). 3. Remove mounting screws (203a). NOTE: You may prefer to remove the A side air motor air line after you remove the assembly from the frame. 4.
Service 203 202b 202a 222 207 206 224 209 210 205 205 220 201 212 211 208 204 212 215 212 212 208 204 212 214 219 221 202 207 ti16325a FIG. 18. Air Controls, Pump System Meter System Air Controls Solenoid air Remove Air/Fluid Panel 1. Follow Before Servicing, page 13. 2. Disconnect main air line and solenoid air line. Disconnect fluid lines where they enter the valve stacks. 3. Remove four screws (8) from sides of frame. 4. Remove air/fluid panel assembly. 5.
Service Replace Ball Valve Replace Pressure Gauge(s) 1. See Remove Air/Fluid Panel, page 23. 1. See Remove Air/Fluid Panel, page 23. 2. Remove screw (106b) and washer (106c) from the handle on the front of the panel. 2. Disconnect air line to gauge (105). 3. Remove mounting screws (105a). 3. Remove fittings (113, 114, 121, 122) and ball valve (106). 4. Remove fitting (114) and gauge (105). Replace as needed. 4. Replace fittings and/or valve as needed. 5. Follow steps in reverse order to reassemble.
Service Fluid Controls 108 52 53 4 Remove Dosing Valve Stacks 1. Follow Before Servicing, page 13. 2. Meter-based systems: See Remove Air/Fluid Panel, page 23. 3. Pump-based systems: On inside of panel, remove fluid inlet hose (37). Remove fluid outlet pressure sensor (6). Disconnect fluid fitting (5) from dosing valve stacks (4, 108 if 3-color system). Disconnect fluid outlet lines from fitting (710). Disconnect solvent supply hose from inlet. Fluid inlets, meter-based system. ti16674a FIG. 22.
Service Dosing Valve Manifold Rebuild Order Kit 24H254 (see page 49). Use all parts in the kit. 711 1. Follow Steps 1 - 5 in Remove Dosing Valve Stacks, page 25. 706 2. Remove fitting (710) and o-ring (708). 3. Remove the dosing valve (705), then remove seat (703) and o-rings (702 and 704) from each side of each manifold (701, 706). 708 707 709 4. 3-Color Systems. Remove the spacer (707) and o-rings (708 and 709) from between the two manifolds (706). 5. 3-Color Systems.
Service Repair Flow Meters Installation 1. Secure meter (103) and spacer (104) to the fluid plate (101) with screws (110) and washers (109). 2. Connect cable harness (118) and fluid line. Coriolis Meter 1. Follow Before Servicing, page 13. 3. Calibrate meter as instructed in the Operation manual 3A0869. 2. To remove and service the Coriolis meter, see manual 313599. Repair Mix Manifold 1. Follow Before Servicing, page 13. G3000 Meter 2. See FIG. 25, page 28. Disconnect fluid lines. Removal 1.
Service 52, 53 13 ti15697a ti16682a Disconnect fluid lines. FIG. 25.
Service Pump Assembly 15 16 16 Prior to service, remove the displacement pump first, then the air motor. Remove the Displacement Pump See pages 30-31 for detailed illustration. 1. Follow Pressure Relief Procedure, page 9. 2. Disconnect the fluid line from the pump outlet. See FIG. 26. ti12813a ti12812a 14 FIG. 27. Remove the coupling collars 25 6. Merkur Pumps: Pull up on the TSL reservoir (25) to remove. 7. Use a socket to remove the tie rod nuts (14). 3.
Parts Parts Pump-Based Proportioners, Models 24F088-24F115 9 2 - See page 43 for control box parts. 58 83 58 82 39 10 63 1 8 64 - connects inside box 3 - See page 35 for air controls parts. See page 31 for pump parts. 4 - See page 49 for valve stack parts. 17 37 37 38 4 13 - See page 48 for mix manifold parts.
Parts Pumps 62 54 1 62 18 Connects reed switch (54) and linear sensor (62) to AFCM (302, see page 43). 2 Connects fluid outlet pressure sensor (6) to AFCM (302, see page 43).
Parts Pump-Based Models 24F088-24F115 - Ref. 1 2 3 4 5 6 8 9 10 13 14 15 16 17 18 Part ----------------16F164 15M669 ----112547 109478 262399 15U606 184128 15T311 16F249 M02LH0 M12LN0 M18LN0 19 LW050A LW075A LW100A LW125A LW150A 20 21 22 23 24 25 26 27 37 38 39 40▲ 45 32 LB100B LB150B LW050A LW075A LW100A LW125A LW150A 15M662 15M662 15U691 See Table 16G463 See Table 24A959 ----206966 239083 166421 277853 15X214 105335 Description FRAME CONTROL BOX, see page 43, Refs.
Parts Ref. 46 Part 47 115841 C38211 15T632 48 100133 49 51 52 53 54 55 57 58 62 63 64 66 67 68▲ 77 78 79 82 83 84 87 325▲ Description ELBOW, air inlet M02xxx air motors All other air motors KIT, Air Flow Switch, see page 50, Refs.
Parts Parts that Vary by Model, Pump-Based Model Non-IS 24F088 24F089 24F090 24F091 24F092 24F093 24F094 24F095 24F096 24F097 24F098 24F099 24F100 24F101 34 IS 24F102 24F103 24F104 24F105 24F106 24F107 24F108 24F109 24F110 24F111 24F112 24F113 24F114 24F115 Adapter Air Plate Motor (Item 17) 16F249 ------------16F249 --------16F249 ------------16F249 --------- (Item 18) M02LH0 M12LN0 M12LN0 M12LN0 M02LH0 M12LN0 M18LN0 M02LH0 M12LN0 M12LN0 M12LN0 M02LH0 M12LN0 M18LN0 “A” Lower “B” Lower “A” “B” Lowe
Parts Air Controls, Pump-Based Models 24F088-24F115 203 202b 202a 222 207 223 206 224 209 210 205 205 220 201 212 211 208 204 212 215 212 212 208 204 212 214 219 221 202 207 Ref.
Parts Tubing Chart, Pump-Based Models 24F088-24F115 Type Color Air Air Air Air Air Air Air Air Air Air Air Fluid Fluid Fluid Fluid Air Air * Description Green Green Green Green Red Red Red Red Natural Natural Natural ------------Natural Black Starting Point Ending Point Solvent Valve A On Dose Valve A On Solvent Valve B On Dose Valve B On Solvent Valve A Off Dose Valve A Off Solvent Valve B Off Dose Valve B Off Solenoid Air Air Regulator to Pump B Air Regulator to Pump A Pump B to Valve Stack B Pump
Parts GFB1-A ATOM-1 ATOM-2 A2 A3 A Side B Side A1 A3 ti16772a 2G 4G 4R 2R 1R 3R 3G 1G A4 A5 A Side B Side ti16765a A5 A4 A6 A7 ti16766a See Manual 312784 for full setup instructions for a gun flush box.
Parts Meter-Based Proportioners, Models 24F080-24F087 9 2 - See page 43 for control box parts. 58 1 83 82 39 10 63 68 53 52 64 - connects inside box 105 108 - See page 49 for valve stack parts. 37 111 8 103 110 109 101 52 53 106 4 - See page 49 for valve stack parts. 102 38 103 118 38 104 118 37 111 104 13 - See page 48 for mix manifold parts.
Parts 117 106b 112 105 120 106c 106a 106 209 ti16298a 122 121 113 123 115 116 114 Meter-Based Models 24F080-24F087 Ref. 1 2 4 Part ------------- 8 9 10 13 27 35 37 38 39 40▲ 47 52 53 57 58 63 64 66 67 ----112547 109478 262398 ----117356 206966 114339 277853 15X214 15T632 C19798 100527 120685 115313 16E883 123278 --------- 68▲ 82 83 87 90 101 102 103 104 15W776 111307 121224 16F793 16G607 ----114342 289813 16F063 3A0870L Description FRAME, meter CONTROL BOX, see page 43, Refs.
Parts Ref. Part 105 15T500 105a ----106 118762 106a ----106b ----106c ----108 ----109 100527 110 117029 111 501867 112 107404 113 100081 114 C19675 115 15T498 116 C20365 117 517312 118 258528 120 114153 121 158491 122 512905 123 114366 124 117793 209 114124 230 262028 325▲ 15W598 Description GAUGE, air pressure SCREW, mounting, gauge VALVE, ball, vented, 1/2 in.
Parts Tubing Chart, Meter-Based Models 24F080-24F087 Type Air Air Air Air Air Air Air Air Air Air Air Air Air Air Air Fluid Fluid Air Air * Color Description Green Solvent Valve A On Green Dose Valve A1 On Green Solvent Valve B On Green Dose Valve B On Green Dose Valve A2 On Green Dose Valve A3 On Red Solvent Valve A Off Red Dose Valve A1 Off Red Solvent Valve B Off Red Dose Valve B Off Red Dose Valve A2 Off Red Dose Valve A3 Off ----Main Air to Pressure Gauge Natural Solenoid Air Natural Main Air to Filt
Parts See Manual 312784 for full setup instructions for a gun flush box.
Parts Control Box 310 306 309 301 304 313 315 330 329 307 305 308 ti16421a 318 338 - 3-color models have 2 additional solenoids here. 68 325 320 302 316 339 317 326 311 314 321 Ref. 68▲ 301 302 302a 302b 303 304 305 306 Part 15W776 ----16F357 103854 ----110637 16E943 121628 117356 307 114263 308 309 310 311 312 100139 C06061 112698 122000 15V778 313 314 113796 ----- 3A0870L 303 Description Qty.
Parts USB Module 341 Purchase cable separately. See CAN Cable options below. 342 349 343 342 345 348 346 340 ti16427a Ref. Part 340 16F358 341 121417 342 102063 343 195875 345 24H084 346 15R325 347 15X214 348 16G873 349 195874 Description USB MODULE with TOKEN SCREW WASHER SCREW, grounding USB HARNESS COVER, bulkhead LABEL, warning BRACKET, grounding SCREW, grounding Qty. 1 4 2 1 1 1 1 1 1 NOTE: Order Kit 24H253 to add a USB Module. Includes all parts shown and instructions.
Parts Electric Power Assembly 402 401 405 407 410 403 411 404 406 Ref. Part Description 401 15V747 POWER SUPPLY, 24 VDC, 2.5 A, 60 watt, B-code, with cable 402 116320 SWITCH, rocker, power 403 115306 FILTER, power line 404 114095 BLOCK, terminal 405 112144 SCREW, machine, pan head 406 109467 SCREW, machine, pan head 407 103832 SCREW, mach 408 100139 PLUG, pipe, not shown 410 ----HARNESS, 2-wire; 8 in. (203 mm) 411 ----HARNESS, 3-wire; 4 in. (102 mm) Qty.
Parts Alternator Power Assembly 511 501 J1 Connect cable 517 to fluid control module. 510 509 508 504 505 J2 Connect cable 516 to USB module, if present. J3 Connect cable 515 to display module. 506 Ref.
Parts Alternator Module 255728 501f 501k 501h 501a 501j 501d 501e 501b Ref. 501a 501b 501c 501d 501e 501f 501g▲ 501h 591j 501k▲ 3A0870L Part ------------257147 ----122161 15R337 114380 122848 172953 Description HOUSING, upper and lower GASKET, stacked, internal GASKET, housing TURBINE BOARD, assy. FITTING, air LABEL, warning, not shown SCREW, cap, socket head FITTING, air LABEL, grounding 501c 501a Qty.
Parts Sequential Dosing Mix Manifold 262398 Dynamic Dosing Mix Manifold 262399 605 604 623 625 622 602 611 613 628 618 620 627 614 607 615 617 619 611 632 603 621 626 601 611 616 617 617 616 611 606 603 619 615 624 630 631 629 614 608 606 618 613 611 610 609 617 601 602 605 ti16301a Ref.
Parts 706 711 705 702 703 704 706 708 708 707 709 710 ti16791a 1-Color/1 Solvent Valve Stack Ref. Part 702*† ----703*† ----704*† ----705 15X303 706◆ 16F057 Description O-RING SEAT, valve O-RING, PTFE VALVE, dispense MANIFOLD, valve, 1-color, 303 stainless steel 708* 110004 O-RING 710 16F064 FITTING, CC Qty. 2 2 2 2 1 705 702 703 704 712 708 710 2 1 701 ti16302a --- Parts not sold separately. 3-Color/1 Solvent Valve Stack * Ref.
Parts Air Flow Switch Kit 15T632 812 807 807 900 808 903 801 904 901 902 ti16428a 809 810 Ref. Part 900 119159 901 ----902 ----903 ----904 ----- 803 811 802 804 Description SWITCH, air flow FITTING ELBOW, 1/4 npt NIPPLE, 1/4 x 1/4 npt CONNECTOR, tube Qty. 1 1 1 1 1 ti16426a Pump Stand Kit 24F301 Meter Stand Kit 24G611 Ref.
Accessories Accessories ProMix 2KE systems are not approved for use in hazardous locations unless the base model, all accessories, all kits, and all wiring meet local, state, and national codes. Part Description USB Module 16F358 USB Module Kit, see page 44 Air Flow Switch 15T632 Air Flow Switch, see page 50 Power Kits 16G351 Electric Power Kit, see page 45 16G353 Alternator Power Kit, see page 46 Cables 123278 10 ft (3.05 m), Yellow, IS CAN Cable, male x female 123280 50 ft (15.
AIR REGULATOR GAUGE MERKUR MOTOR A 52 PUMP A PILOT AIR REGULATOR PUMPS SYSTEMS ONLY 3/4" AIR FILTER AUTO DRAIN 20 MICRON RELIEF VALVE 85/110 PSI (.58/.76 MPa, 5.8/7.6 BAR) PUMPS SYSTEMS ONLY AIR INPUT GAUGE GAUGE PUMP B PILOT ALTERNATOR AIR REG. 18 PSI (.12 MPa, 1.2 BAR) 3/8" AIR FILTER AUTO DRAIN 5 MICRON 100 PSI (.7 MPa, 7 BAR) 3/4" BALL VALVE BLEED TYPE MERKUR MOTOR B 3/8" TUBE TO MANIFOLD AIR SUPPLY RELIEF VALVE 20 PSI (.12 MPa, 1.
AIR REGULATOR GAUGE MERKUR MOTOR A PUMP A PILOT 3A0870L PUMPS SYSTEMS ONLY 3/4" AIR FILTER AUTO DRAIN 20 MICRON RELIEF VALVE 85/110 PSI (.58/.76 MPa, 5.8/7.6 BAR) AIR REGULATOR PUMPS SYSTEMS ONLY AIR INPUT GAUGE GAUGE PUMP B PILOT 3/8" AIR REG. AUTO DRAIN 5 MICRON 100 PSI (.
Schematics Hazardous Location Electrical Schematic J1 CAN_L +V_CAN V_CAN_RTN CAN_H SHIELD 1 2 3 4 5 ALTERNATOR MODULE 18 PSI 1.
Schematics Hazardous Location Electrical Schematic (continued) J7 J8 FLUID CONTROL MODULE J4 UNUSED ALARM (+) COMMON PURGE A (+) DOSE A1 (+) UNUSED UNUSED UNUSED UNUSED UNUSED 1 2 3 4 5 1 2 3 4 5 CAN_L +V_CAN V_CAN_RTN CAN_H SHIELD 1 2 3 4 5 J5 UNUSED AFS #1 (+) COMMON PURGE B (+) DOSE B (+) 1 2 3 4 5 J13 J12 +12 VDC FLOW METER B SIG COMMON GFB INPUT/AFS #2 (+) GFB OUTPUT 1 2 3 4 5 1 2 3 4 5 J3 J2 +5 VDC AI (-) COMMON AI (+) SHIELD "A" PRESSURE TRANSDUCER +5 VDC AI (-) COMMON AI (+) SHI
Schematics Non-Hazardous Location Electrical Schematic J1 L N GRND L GRND N CAN_L +V_CAN V_CAN_RTN CAN_H SHIELD 1 2 3 4 5 TERMINAL BLOCK POWER SUPPLY LINE POWER FILTER L N P4 P3 2A 2 SWITCH ROCKER CAN_L +V_CAN V_CAN_RTN CAN_H SHIELD 1A 1 2 3 4 5 1 2 3 4 5 J2 P1 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 USB BASE MODULE J6 CAN_L +V_CAN V_CAN_RTN CAN_H SHIELD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 J4 LED_YELLOW LED_BLUEA LED_GREEN UNUSED LED_BLU
Schematics Non-Hazardous Location Electrical Schematic (continued) J7 J8 CAN_L +V_CAN V_CAN_RTN CAN_H SHIELD 1 2 3 4 5 FLUID CONTROL MODULE J4 UNUSED ALARM (+) COMMON PURGE A (+) DOSE A1 (+) CAN_L +V_CAN V_CAN_RTN CAN_H SHIELD 1 2 3 4 5 J5 UNUSED AFS #1 (+) COMMON PURGE B (+) DOSE B (+) 1 2 3 4 5 1 2 3 4 5 J13 J12 +12 VDC FLOW METER B SIG COMMON GFB INPUT/AFS #2 (+) GFB OUTPUT 1 2 3 4 5 1 2 3 4 5 J3 J2 +5 VDC AI (-) COMMON AI (+) SHIELD "A" PRESSURE TRANSDUCER +5 VDC AI (-) COMMON AI (+)
Schematics 58 3A0870L
Technical Data Technical Data ProMix® 2KE Maximum fluid working pressure Maximum working air pressure Air supply Air filter inlet size Air filtration for air logic (Graco-supplied) Air filtration for atomizing air (user-supplied) Mixing ratio range On-ratio accuracy Fluids handled Viscosity range of fluid Fluid filtration (user-supplied) Fluid flow rate range G3000, G250 Meter G3000HR, G250HR Meter Coriolis Meter S3000 Solvent Meter (accessory) Fluid inlet sizes Flow Meter Dose Valve/Color Valve Adapters
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.