Repair-Parts ProMix® PD2K Electronic Proportioner 3A2800B EN Positive displacement proportioning of 2-component materials helps reduce waste. Manual system with Advanced Display Module. For professional use only. Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 3 for model part numbers and approvals information. PROVEN QUALITY. LEADING TECHNOLOGY.
Contents Models............................................................... 3 Related Manuals ................................................ 5 Warnings ........................................................... 6 Important Isocyanate (ISO) Information ................ 9 Troubleshooting.................................................. 11 System Troubleshooting ............................... 11 Error Code Troubleshooting.......................... 12 Booth Control Troubleshooting......................
Models Models See Figs. 1–7 for component identification labels, including approval information and certification. Part No. Series Maximum Air Working Pressure Maximum Fluid Working Pressure MC1000 A 100 psi (0.7 MPa, 7.0 bar) 300 psi (2.068 MPa, 20.68 bar) MC2000 A 100 psi (0.7 MPa, 7.0 bar) 1500 psi (10.34 MPa, 103.
Models Figure 3 Model MC2000 (High Pressure) Identification Label Figure 4 Non-Intrinsically Safe Color Change Control (Accessory) Identification Label Figure 5 Intrinsically Safe Color Change Control (Accessory) Identification Label Figure 6 Booth Control Identification Label Figure 7 Pump Expansion Kit (Accessory) Identification Label 4 3A2800B
Related Manuals Related Manuals Manual No. Description Manual No.
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
Warnings INTRINSIC SAFETY WARNING Intrinsically safe equipment that is installed improperly or connected to non-intrinsically safe equipment will create a hazardous condition and can cause fire, explosion, or electric shock. Follow local regulations and the following safety requirements.
Warnings WARNING TOXIC FLUID OR FUMES Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed. • Read MSDSs to know the specific hazards of the fluids you are using. • Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines. • Always wear chemically impermeable gloves when spraying, dispensing, or cleaning equipment.
Important Isocyanate (ISO) Information Important Isocyanate (ISO) Information Isocyanates (ISO) are catalysts used in two component materials. Keep Components A and B Separate Isocyanate Conditions Cross-contamination can result in cured material in fluid lines which could cause serious injury or damage equipment. To prevent cross-contamination: Spraying or dispensing materials containing isocyanates creates potentially harmful mists, vapors, and atomized particulates.
Important Isocyanate (ISO) Information Changing Materials NOTICE Changing the material types used in your equipment requires special attention to avoid equipment damage and downtime. • When changing materials, flush the equipment multiple times to ensure it is thoroughly clean. • Always clean the fluid inlet strainers after flushing. • Check with your material manufacturer for chemical compatibility.
Troubleshooting Troubleshooting NOTE: Check all possible remedies before disassembling the system. System Troubleshooting Problem Cause Solution Unit will not operate. Inadequate power supply. See Technical Data, page 59. Power switch is off. Turn switch on. Main power is shut off. Turn main power switch on. Exhausted fluid supply. Refill and reprime pump. Clogged fluid outlet line, valves, etc. Clear. Fluid dried on piston rod. Disassemble and clean pump. See pump manual.
Troubleshooting Error Code Troubleshooting System errors alert you of a problem and help prevent off-ratio spraying. There are three types: Advisory, Deviation, and Alarm. An Advisory records an event in the system, and will clear itself after 60 seconds. A Deviation records an error in the system but does not shut down the equipment. The deviation must be acknowledged by the user. NOTE: When an error occurs be sure to determine the code before resetting it.
Troubleshooting Code Type B9S0 Problem Cause Solution Advisory Volume Rollover Solvent Current Batch counter for material S rolled over. The totalizer has reached maximum capable value and started over at zero. n/a B9SX Advisory Volume Rollover Solvent Lifetime Grand total counter for material S rolled over. The totalizer has reached maximum capable value and started over at zero. n/a CAC# Alarm Comm. Error Color Change # System does not see the Color Change Module #.
Troubleshooting Code Type Description Problem Cause Solution CDDX Alarm Duplicate Fluid Module System sees two or more identical Fluid Control Modules. More than one Fluid Control Module is connected in the system. Check the system and remove the extra fluid control module. CDNX Alarm Duplicate Booth Control System sees two or more identical Booth Control Modules. More than one Booth Control Module is connected in the system. Check the system and remove the extra booth control module.
Troubleshooting Code Type Description Problem Cause Solution DG0# Alarm No Stall Down Pump # Pump stall test failed; pump did not stall on the down stroke. Valve failure, seal failure, worn rod or cylinder. Replace inlet and outlet valve and seal for down stroke. Replace piston and throat seals. Replace rod and cylinder as necessary. DH0# Alarm No Stall Pump # Pump stall test failed; pump did not stall on either the up or down stroke. Valve failure, seal failure, worn rod or cylinder.
Troubleshooting Code Type Description Problem Cause Solution EF1# Alarm Timeout Shutdown Pump # Pump tried but was not able to move to the park position within a specified amount of time. Pump dose valves did not actuate. Visually inspect valves to ensure they are operating properly; verify they have air pressure above 85 psi (0.6 MPa, 6.0 bar). Pump is filled with thick paint and could not drive piston to end of stroke. Motor or drive is worn or damaged.
Troubleshooting Code Type Description Problem EQU3 Record EQU4 Record USB Custom Lang. Uploaded EQU5 Record Data logs were USB Logs Downloaded downloaded to USB drive. ES00 Advisory Factory Defaults Record of defaults being loaded. EVUX Advisory USB Disabled USB drive has been inserted, downloading is disabled. Configuration of system is blocking data transfer. Change configuration to enable USB download function. F1F# Alarm There has been no/low flow during a fill pump operation.
Troubleshooting Code Type Description Problem Cause Solution F7P1 Alarm Flow Detected Air Gun The air flow switch is indicating unexpected atomizing air flow. Air flow switch is stuck in flow position. Clean or replace switch. Leak downstream in air line or fitting. Check for leaks and tighten fittings. Air supply pressure fluctuation. Eliminate pressure fluctuations. F7S1 Alarm Flow Detected Solvent Gun The solvent flow switch is indicating unexpected solvent flow.
Troubleshooting Code Type Description Problem Cause Solution P6D# Alarm Press. Sens. Removed Outlet # Outlet pressure transducer has been disconnected when the system is expecting one. Disconnected transducer. Verify transducer is connected properly. Replace if reconnecting does not eliminate the alarm. P9D# Alarm Press. Sens. Failed Outlet # Outlet pressure transducer has failed. Outlet pressure transducer has failed or the pressure is above the readable range. Relieve system pressure.
Troubleshooting Code Type Description Problem Cause Solution SAD1 Alarm Atomizing Solvent AFS is active while solvent, diluted material, or an unknown material is in the gun. Atomizing air supply was not shut off before purging or filling spray gun. Make sure atomizing air is shut off before purging or filling the spray gun. Use an AA cutoff valve on the atomizing air supply.
Troubleshooting Maintenance Error Codes Perform the required maintenance if the following codes occur. Code Type Name Description END# Record Calibration Pump # A calibration test was run on the pump. ENS0 Record Calibration Solvent Meter A calibration test was run on the solvent meter. ENT# Record Calibration Stall Test Pump # A stall test was completed successfully on pump #. MAD# Advisory Maint. Outlet Pump # Maintenance is due on pump. MAT# Advisory Maint.
Troubleshooting Booth Control Troubleshooting Figure 9 Bottom View of Booth Control Figure 8 Booth Control Table 1 . Booth Control Diagnostics Indicator Description Diagnosis Mix Mode (green) LED is on when in Mix mode. LED blinks when in Mix Fill mode. Also blinks is Mix Idle mode (together with Standby LED). Purge Mode (green) LED is on when in Purge mode. LED blinks when a purge is needed. Pressure Change Mode (green) LED blinks when in Pressure Change mode.
Troubleshooting Power Barrier Board Troubleshooting Figure 10 Power Barrier Board Table 2 . Power Barrier Board Diagnostics Component or Indicator Description Diagnosis D4 LED (green) IS Power D5 LED (green) Power F3 Fuse, 400 mA, 250 V F4 Fuse, 400 mA, 250 V If either F3 or F4 is blown, there is no power to the IS location. D4 is out.
Troubleshooting Isolation Board Troubleshooting Figure 11 Isolation Board Table 3 . Isolation Board Diagnostics Component or Indicator Description Diagnosis D6 LED (yellow) IS Communication D7 LED (green) IS Power D8 LED (green) Non-IS Power D14 LED (yellow) Non-IS Communication J1 Connector Non-IS J2 Connector Non-IS J3 Connector Intrinsically Safe J4 Connector Intrinsically Safe S1 Pushbutton Switch For Non IS connectors. If switch S1 is off, yellow LED (D14) is steady on.
Troubleshooting Enhanced Fluid Control Module Troubleshooting Figure 12 Enhanced Fluid Control Module Table 4 .
Troubleshooting Pump Module Troubleshooting Figure 13 Pump Module Table 5 .
Troubleshooting Advanced Display Module Troubleshooting Figure 14 Advanced Display Module Table 6 .
Notes Notes 28 3A2800B
Electrical Schematics Electrical Schematics NOTE: The electrical schematic illustrates all possible wiring expansions in a ProMix PD2K system. Some components shown are not included with all systems. NOTE: See Optional Cables and Modules, page 35 for a list of cable options. FAN (24P658) ENCODER AND MOTOR (16P036, 16P037) WIRE HARNESS (24P684, 24P685) PUMP OUTLET TRANSDUCER (16P289, 16P290) MAC SERIES 46 SOLENOID (16P812) PUMP V/P FOR FLUID REG.
Electrical Schematics CONTINUED ON PAGE 3 CONTINUED ON PAGE 3 (NON IS) (IS) 3 (24M485) UNUSED UNUSED SOLVENT CUTOFF BARRIER BOARD (248192) UNUSED 8 3 1 2 3 4 5 6 7 8 9 10 11 12 5 (121227) GCA MODULE EFCM (24N913) PWR (RED) SIG (WHITE) COM (BLACK) SHIELD/GRN SOLVENT METER (258718) RED WIRE (065161) +12VDC COM UNUSED UNUSED +12VDC COM +12VDC COM UNUSED GROUND BAR BLACK WIRE (065159) 1 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 4 25 PIN D-SUB CABLE (16T659) 24
Electrical Schematics GUN TRIGGER INPUTS SIG COM SIG COM SIG COM SIG COM SIG COM SIG COM 7 1 2 3 4 5 6 7 8 9 10 11 12 FLOW RATE ANALOG IN 1 FLOW RATE ANALOG COMMON 1 FLOW RATE ANALOG IN 2 FLOW RATE ANALOG COMMON 2 FLOW RATE ANALOG IN 3 FLOW RATE ANALOG COMMON 3 FLOW RATE ANALOG IN 4 FLOW RATE ANALOG COMMON 4 UNUSED UNUSED UNUSED UNUSED 9 1 2 3 4 5 6 GCA MODULE EFCM (24N913) 3 4 LIGHT TOWER (15X472) 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 BREAKOUT MODULE PUMP 3 (24N
Electrical Schematics FROM CAN IS BOARD (24M485) ON PAGE 2 FROM CAN IS BOARD (24M485) ON PAGE 2 2 CABLE (15V206) MANIFOLD FLUSH COLOR 1 COLOR 2 COLOR 3 COLOR 4 COLOR 5 COLOR 6 COLOR 7 COLOR 8 +12VDC COM +12VDC COM +12VDC COM 1 2 3 4 5 6 +12VDC COM +12VDC COM +12VDC COM 1 2 3 4 5 6 +12VDC COM +12VDC COM +12VDC COM 1 2 3 4 5 6 12 34 5 COLOR CHANGE MODULE 1 (COLORS 1 THRU 8) J8 J9 1 2 3 4 5 6 +12VDC COM +12VDC COM +12VDC COM J16 1 2 3 4 5 6 +12VDC COM +12VDC COM +12VDC COM J10 1 2 3 4 5 6
Electrical Schematics MANIFOLD FLUSH CATALYST 3 CATALYST 4 +12VDC COM +12VDC COM +12VDC COM 1 2 3 4 5 6 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED 1 2 3 4 5 6 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED 1 2 3 4 5 6 CATALYST CHANGE MODULE 6 (CATALYST 3 THRU 4) J8 J9 1 2 3 4 5 6 +12VDC COM +12VDC COM +12VDC COM J16 1 2 3 4 5 6 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED J10 1 2 3 4 5 6 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED 6 J15 J14 MANIFOLD DUMP CATALYST 3 CATALYST 4 2 CABLE (15V206)
Electrical Schematics FROM CAN IS BOARD (24M485) ON PAGE 2 NON-HAZARDOUS LOCATION HAZARDOUS LOCATION MANIFOLD COLOR FLUSH COLOR 1 COLOR 2 COLOR 3 COLOR 4 COLOR 5 COLOR 6 COLOR 7 COLOR 8 12 34 5 COLOR CHANGE MODULE 7 (COLORS 33 THRU 40) +12VDC COM +12VDC COM +12VDC COM 1 2 3 4 5 6 J8 +12VDC COM +12VDC COM +12VDC COM 1 2 3 4 5 6 J15 +12VDC COM +12VDC COM +12VDC COM 1 2 3 4 5 6 J9 1 2 3 4 5 6 +12VDC COM +12VDC COM +12VDC COM J16 1 2 3 4 5 6 +12VDC COM +12VDC COM +12VDC COM 1 2 3 4 5 6 +12VD
Electrical Schematics Optional Cables and Modules NOTE: The total length of all cable used in the system must not exceed 150 ft (45 m). See the Electrical Schematics, page 29. M12 CAN Cables, for Hazardous Locations CAN Cables, for Non-Hazardous Locations Only NOTE: The total length of cable used in the hazardous location must not exceed 120 ft (36 m). Cable Part No. Length ft (m) Cable Part No. Length ft (m) 125306 1.0 (0.3) 16V423 2.0 (0.6) 123422 1.3 (0.4) 16V424 3.0 (1.0) 121000 1.6 (0.
Repair Repair Before Servicing • Servicing the electrical control box exposes you to high voltage. To avoid electric shock, turn off power at the main circuit breaker before opening the enclosure. • All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations. • Do not substitute or modify system components as this may impair intrinsic safety. 1. Flush the system as explained in your PD2K Operation Manual if service time may exceed pot life time.
Repair Pressure Relief Procedure With Color Change Follow the Pressure Relief Procedure whenever you see this symbol. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment.
Repair Repairing the Advanced Display Module (ADM) To replace the Advanced Display Module, disconnect the cable from the module and remove the module from the bracket. Install the new module on the bracket and attach the cable. 3. Insert and press token (T) firmly into slot. NOTE: There is no preferred orientation of the token. Figure 24 Insert Token 4. Turn the power switch back on. The red indicator light (L) will flash until the new firmware is completely loaded. 5. Remove the token (T). 6.
Repair Servicing the Control Box Replacing the Isolation Board NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. To avoid electrical component damage, remove all system power before plugging any connectors. 1. Follow the steps in Before Servicing, page 36. 2. Loosen the screws (124) and remove the enclosure cover (117). 3. Note the position of the isolation board cables.
Repair Replacing the Barrier Board NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. To avoid electrical component damage, remove all system power before plugging any connectors. 1. Follow the steps in Before Servicing, page 36. 2. Loosen the screws (124) and remove the enclosure cover (117). 3.
Repair Replacing the EFCM Control Module NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. To avoid electrical component damage, remove all system power before plugging any connectors. 8. Load the software. See Install Key Token or Upgrade Token, page 38. 9. Turn on the control box power switch. Check that the green is on, the orange and yellow LEDs are blinking, and the red LED is off. 10.
Repair Replacing the 24 Vdc Power Supply NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. To avoid electrical component damage, remove all system power before plugging any connectors. 8. Turn on power at the main circuit breaker. 9. Turn on the control box power switch.
Repair Replacing the 48 Vdc Pump Power Supply NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. To avoid electrical component damage, remove all system power before plugging any connectors. 8. Turn on power at the main circuit breaker. 9. Turn on the control box power switch. Press to turn pump power on. NOTE: The 48V green LED on each of the pump control modules (132) will light when operating. 1.
Repair Replacing a Pump Control Module NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. 8. Turn on the control box power switch. Check that the 48V green LED and the 24V green LED on each of the pump control modules (132) are on. 9. Reinstall the cover (117) and tighten the screws (124). To avoid electrical component damage, remove all system power before plugging any connectors. 1.
Repair Replacing the Line Filter NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. To avoid electrical component damage, remove all system power before plugging any connectors. 1. Follow the steps in Before Servicing, page 36. 2. Loosen the screws (124) and remove the enclosure cover (117). 3. Note the position of the line filter input and output wires. See Electrical Schematics, page 29.
Repair Replacing the Power Switch NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. 7. Reinstall the cover (117) and tighten the screws (124). 8. Turn on power at the main circuit breaker. To avoid electrical component damage, remove all system power before plugging any connectors. 1. Follow the steps in Before Servicing, page 36. 2. Loosen the screws (124) and remove the enclosure cover (117). 3.
Repair Replacing the Air Flow Switch NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. 8. Turn on power at the main circuit breaker. 9. Turn on the control box power switch. To avoid electrical component damage, remove all system power before plugging any connectors. 1. Follow the steps in Before Servicing, page 36. 2. Loosen the screws (124) and remove the enclosure cover (117). 3.
Repair Servicing the Fluid Section Removing a Pump Installing a Pump 1. Slide the pump into the mounting bracket (4). Tighten the jam nuts to secure. 2. Install the pump bracket (7) and screws (15). 1. Follow the steps in Before Servicing, page 36. 2. Remove the screws (56) holding the cover (8) to the front of the unit. 3. Connect the fluid inlet and outlet lines to the pump manifolds (IN, OUT). 4. Connect the air lines to the dosing valves (V). 3. Disconnect the cable from the pump driver (101). 5.
Repair Replacing a Solenoid NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. To avoid electrical component damage, remove all system power before plugging any connectors. 1. Follow the steps in Before Servicing, page 36. 2. Remove the screws (56) holding the cover (8) to the front of the unit. 3. Loosen the screws (124) and remove the enclosure cover (117). 4.
Repair Replacing a Fan 2. Remove the screws (56) holding the cover (8) to the front of the unit. NOTICE To avoid damaging the circuit boards when servicing the control box, wear Part No. 112190 grounding strap on your wrist and ground appropriately. To avoid electrical component damage, remove all system power before plugging any connectors. 1. Follow the steps in Before Servicing, page 36. 3. Loosen the screws (124) and remove the enclosure cover (117). 4.
Repair Replacing the Solvent Flow Switch Replacing the Solvent Valve 1. Follow the steps in Before Servicing, page 36. 2. Remove the screws (56) holding the cover (8) to the front of the unit. 3. Disconnect the solvent flow switch wires from J6 pins 11–12 on the EFCM. See Electrical Schematics, page 29. 4. Disconnect the solvent lines. 5. Unscrew the adapter (45) from the solvent flow switch (19). 6. Unscrew the solvent flow switch from the elbow (18). 1. Follow the steps in Before Servicing, page 36. 2.
Parts Parts Proportioner Parts Part No. MC1000 Low Pressure Proportioner Part No.
Parts Part No. MC1000 Low Pressure Proportioner Part No.
Parts Description Qty Ref 30 Part ——— WASHER; 3/8 40 54 31 ——— 4 32 ——— SCREW, cap, hex head; 3/8–16 x 2.75 in. (70 mm) SCREW, cap, hex head; 3/8–16 x 7/8 in. (22 mm) NUT, lock; 3/8–16 Ref 33 ——— 34 ——— 35 10 56 223547 ——— 69 ——— 70 16V429 73 24T302 73a ——— 73b 24U617 73c ——— 73d ——— A/R 73e ——— A/R 74 166421 10 8 ——— SCREW, cap, hex head; 3/8–16 x 3 in.
Parts Control Box Parts Electrical Control Box 3A2800B 55
Parts Electrical Control Box (continued) 101 Part ——— 102 ——— 103 24T769 104 Description 110 Part ——— BRACKET, board 2 111 24M485 BOARD, isolation, IS 1 1 112 16U725 1 3 113 ——— SWITCH, selector, 2 position DUCT, wire SPACER, standoff 3 114 ——— COVER, duct 2 BOARD, barrier; includes item 106a FUSE; 400 mA, quick acting COVER, barrier 1 115 FILTER , line; 10A 1 116 16V446 ——— BLOCK, terminal 1 117 ——— COVER, enclosure 1 1 118 ——— GROMMET 2 SCREW, machine, pan
Parts 121 Part ——— 122 ——— 123 ——— 124 ——— Ref Description Qty Ref CONNECTOR, bar, ground SCREW, ground; M5 x 0.8 NUT, hex, flange head; 1/4–20 SCREW, flanged, hex head; 1/4–20 x 0.75 in. (19 mm) SCREW, machine, pan head; 10–24 x 0.375 in. (10 mm) SCREW, machine, pan head; 10–32 x 0.75 in. (19 mm) FITTING, connector; 1/8 npt(m) x 1/4 in. (6 mm) OD tube SCREW, machine, pan head; 8–32 x 0.25 in. (6 mm) SCREW, machine, binding head; 6–32 x 0.25 in. (6 mm) CABLE, CAN; fbe; 3.
Parts Solenoid Manifold Parts Part No. 24T772 Solenoid Manifold Description Qty 301 Part ——— PLATE 1 302 ——— MANIFOLD 1 303 ——— 4 304 115671 305 16P812 SCREW, cap, socket head; 1/4–20 x 0.375 in. (10 mm) CONNECTOR; 1/8 npt(m) x 1/4 in. (6 mm) OD tube VALVE, solenoid 307 114151 308 114263 309 C06061 Ref FITTING, elbow, swivel; 1/8 npt(m) x 5/32 in. (4 mm) OD tube FITTING, straight; 1/8 npt(m) x 5/32 in.
Technical Data Technical Data U.S. Metric MC1000 Air Spray Systems 300 psi 2.1 MPa, 21 bar MC2000 Air-Assisted Spray Systems 1500 psi 10.5 MPa, 105 bar 100 psi 0.7 MPa, 7.0 bar Positive Displacement Proportioner Maximum fluid working pressure: Maximum working air pressure: Air supply: 85–100 psi 0.6–0.7 MPa, 6.0–7.
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
