Repair - Parts XM PFP 3A2989G EN For spraying two-component intumescent epoxies. For professional use only. Not for use in explosive atmospheres or hazardous locations. Important Safety Instructions Read all warnings and instructions in all supplied manuals. Save all instructions. See page 3 for model information, including maximum working pressure and approvals.
Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Keep Components A and B Separate . . . . . . . . 6 Changing Materials . . . . . . . . . . . . . . . . . . . . . . . 6 Components A and B . . . . . . . . . . . . . . . . . . . . . 6 Component Identification . . . . . . . . . . . . . . . . . . . . 6 Grounding . . . . . . . . .
Models Models Models Maximum Fluid Working Pressure Maximum Air Working Pressure Approvals A and B Materials: 6000 psi (41 MPa, 414 bar) 262869 24W626 Flushing Fluid: 4500 psi (31 MPa, 310 bar) Supply: 150 psi (1.0 MPa, 10.3 bar) Max. Setpoint: 100 psi (0.7 MPa, 7 bar) Heating Fluid: 100 psi (0.7 MPa, 7 bar) 9902471 Certified to CAN/CSA C22.2 No. 88 Conforms to UL 499 Related Manuals Manuals are available at www.graco.com.
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
Warnings WARNING WARNING MOVING PARTS HAZARD Moving parts can pinch, cut or amputate fingers and other body parts. • Keep clear of moving parts. • Do not operate equipment with protective guards or covers removed. • Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure and disconnect all power sources. EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury.
Component Identification Keep Components A and B Separate Component Identification See XM PFP Operation manual for component identification. Cross-contamination can result in cured material in fluid lines which could cause serious injury or damage equipment. To prevent cross-contamination: • Never interchange component A and component B wetted parts. • Never use solvent on one side if it has been contaminated from the other side.
Pressure Relief Procedure Pressure Relief Procedure Follow the Pressure Relief Procedure whenever you see this symbol. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. 1. Engage trigger lock. NOTICE The material may expand when air pressure is removed.
Troubleshooting 7. Open recirculation ball valves. 11. Close mix manifold material ball valves. ti20129a WL D 8. Disengage trigger lock. 12. Perform Flush Mixed Material procedure in XM PFP Operation manual to prevent mixed material curing in the system and to relieve pressure in the solvent lines. 13. Close metering pump air supply ball valve. TI19265a1 9. Hold a metal part of the gun firmly to a grounded metal pail. Trigger gun to relieve pressure in material hoses.
Repair Repair NOTICE Do not use air motor lift rings to lift the entire assembly. This will damage the system. The system must be lifted from the bottom. 3. Unscrew filter bowl from inlet air regulator (601d). 4. Remove and replace element. 601d Filter Bowl and Element Follow Pressure Relief Procedure on page 7 if service time may exceed pot life time, before servicing fluid components, and before transporting sprayer. r_312359_313289_15 Replace Air Filter Element 5. Screw filter bowl on securely.
Repair User Interface/Control Box 2. Disconnect solenoid cable connector (542) from the solenoid (509a) being replaced. 3. Remove two screws (509b) from the solenoid being replaced then remove solenoid (509a). See FIG. 4. Remove Shroud and Front Panel of Control Box 1. Close main air shutoff valve on air supply line and on system. Depressurize air line. 2. Remove four nuts (21) and then remove front and rear shrouds (19, 20). 509b 21 r_xm1a00_312359_313289_9_3 509a 20 FIG. 4 19 4.
Repair Update USB Module Software Replace USB Module 1. Remove four nuts (21) and then remove front and rear shrouds (19, 20). 1. Remove Shroud and Front Panel of Control Box, see page 10. 2. Disconnect CAN cables and USB cable from USB module (519). 21 19 ti19926a1 2. Use software token 16P644. See Graco Control Architecture™ Module Programming manual for instructions. NOTE: Upgrade all modules in the system to the software version on the token, even if you are replacing only one or two modules.
Repair Update Fluid Control Module (FCM) Software 3. Loosen four mounting screws (535). r_312359_313289_26 518 1. Remove four nuts (21) and then remove front and rear shrouds (19, 20). 535 21 535 20 19 4. Slide FCM up and out of keyhole slots. ti19926a1 2. Use software token 16P644. See Graco Control Architecture™ Module Programming manual for instructions. NOTE: Upgrade all modules in the system to the software version on the token, even if you are replacing only one or two modules.
Repair Display 6. Turn power off. Upgrade Software 7. Remove token (T). NOTICE To avoid damaging circuit board, wear a grounding strap. 8. Use screws (512) to install access cover (511). Use software token 16P644. See Graco Control Architecture™ Module Programming manual for instructions. NOTE: Upgrade all modules in the system to the software version on the token, even if you are replacing only one or two modules. Different software versions may not be compatible.
Repair Replace Display 6. Discard old display assembly. NOTE: Order display kit 257484 for replacement. 7. Place new front display panel (507) and gasket (513) on front panel of control box (16). NOTICE To avoid damaging circuit board, wear a grounding strap. NOTE: To ease installation use clear tape to hold front display panel in place. 1. Remove Control Box Shrouds, see page 17. 2. Disconnect CAN cable from display module. 8.
Repair Junction Box Replace High Power Temperature Control Module (HPTCM, ref. 404) Update High Power Temperature Control Module (HPTCM, ref. 404) Software NOTE: Upgrade all modules in the system to the software version on the token, even if you are replacing only one or two modules. Different software versions may not be compatible. All data in the module may be reset to factory default settings.
Repair Update Fluid Control Module Cube (FCM3, ref. 415) Software NOTE: Upgrade all modules in the system to the software version on the token, even if you are replacing only one or two modules. Different software versions may not be compatible. All data in the module may be reset to factory default settings. Record all settings and user preferences before the upgrade, for ease of restoring them following the upgrade. The latest software version for each system can be found at Tech Support at www.graco.
Repair Air Controls Remove Control Box Shrouds 1. Close main air shutoff valve on air supply line and on system. Depressurize air line. 2. Remove four nuts (21) and then remove front and rear shrouds (19, 20). 8. Follow steps in reverse order to reassemble. Replace Solvent Air Regulator 1. Remove Control Box Shrouds. 2. Disconnect air motor air lines and system air line. 3. Remove four nuts (17) from front of air controls (18). See page 36. 4. Pull out assembly.
Repair 5. Disconnect air line. 9. Remove regulator assembly (601d) and replace with new. See part number shown in the System Air Controls Module (255761) section beginning on page 44. 6. Remove gauge (606) from block (601e). 7. Remove screws from quick clamps (601f) holding air regulator assembly (601c) in place. 10. Follow steps in reverse order to reassemble. 8. Open clamps (601f) at hinge and pull apart from block (601e). 11. Set new air pressure regulator to at least 80-85 psi (0.55-0.58 MPa, 5.
Repair Dosing Valve Assembly 1. Follow Pressure Relief Procedure, page 7. 6. Remove dosing valves. 2. Disconnect all fluid lines from dosing valves (28 or 29). See FIG. 6. 7. See Ratio Control Valve Assemblies on page 50 for disassembly illustration. 3. Remove two bolts (31) securing dosing valve to bracket. 8. Follow steps in reverse order to reassemble dosing valve assembly. See Ratio Control Valve Assemblies on page 50 for assembly illustration and specifications. 4.
Repair Sensors Replace Temperature (RTD) Sensors This procedure applies to: • Tank sensors mounted in the side of each tank near the bottom (209). Replace Fluid Pressure Sensor • Glycol heater for hose outlet manifold sensor (100). 1. Close main air shutoff valve on air supply line and on system. 1. Close main air shutoff valve on air supply line and on system. 2. Follow Pressure Relief Procedure, page 7. 2. Follow Pressure Relief Procedure, page 7. 3. Open control box cover.
Repair Pump Assembly (System Module) Remove Displacement Pump Follow these instructions for removing only the displacement pump; the air motor will remain installed. 1. Follow Pressure Relief Procedure, page 7. 2. Close ball valve on tank outlet. Prior to servicing the pump assembly you must first remove either the entire pump assembly or the displacement pump and air motor individually. Remove Pump Assembly 3. Disconnect fluid inlet line from the displacement pump. Leave line connected to the tank. 4.
Repair Solvent Pump Remove Air Motor 1. Follow Pressure Relief Procedure, page 7. 2. Disconnect displacement pump from air motor. See steps 2 and 3 under Remove Displacement Pump, page 21. 3. Disconnect sensor cable, air line, and ground wire from air motor. 4. Remove mounting screws (5) and washers (4) holding air motor (2 or 3) to mounting bracket. 2 or 3 1. Follow Pressure Relief Procedure, page 7. 2. Disconnect pump inlet line (154) and air lines (57, 60) from solvent pump. 3.
Repair Heaters Replace 1. Follow Pressure Relief Procedure, page 7. 2. Disconnect fluid lines and electrical wiring from fluid heater. NOTE: See applicable heater manual for wiring, repair, and parts information. See Related Manuals on page 3. Service and Repair 1. Follow Pressure Relief Procedure, page 7. 2. Disconnect fluid lines and electrical wiring from fluid heater. 3. Refer to heater manual to service or repair heater. 3. System Module Heaters: See FIG. 8.
Repair Replace Radar Level Sensor NOTE: Order radar level sensor kit 24T052. See Feed Module (24P883) on page 40 for kit contents. 8. Use a wrench to hold the 3/8 in. flats on the sensor rod. NOTE: Tank level sensors changed in 2014. The old sensors were red. The new sensors are blue. The blue sensors can be used as direct replacements for the red sensors. 9. Tighten to approximately 25 - 30 in-lb (2.8 - 3.4 N•m). Do not over-tighten. 1.
Repair Set Up a New Guided Radar Level Sensor Level sensors need to have three settings setup after installing on the tank of the PFP machine. The tank must be empty, or the level needs to be at least below the bottom of the installed probe with the tank cover closed. 1. Open the sensor head cover over the display: a. Loosen the securing clamp with an Allen wrench (if clamp is present). b. Unscrew the round cover and pull away.
Repair 4. Set FULL CAL to .691 meters. a. Press + to get to FULL CAL, then press E. b. Press + until decimal point (.) appears, then press E. c. Press + until 6 appears, then press E. d. Press + until 9 appears, then press E. e. Press + until 1 appears, then press E. f. Press and hold E until the hourglass appears, then release. 5. Map EMPTY TANK. a. Press + to get to MAPPING, then press E. b. Press E to get to CONFIRM DISTANCE. c. Press + until TANK EMPTY appears, then press E. d.
Electrical Schematics Electrical Schematics Simplified Electrical Schematic Page 1 of 3 DISC1 Switch - 123969 thpole - 123968 4 24VDC POWER 16T147 Din rail PS1 L3 RED +V BLACK -V L2 GND-3 L1 + + 24VDC - Power Supply - CB5-3 3 CB5-1 1 N CB4-3 3 FIELD WIRE SIDE GRACO WIRE SIDE CB4-1 1 CB3-3 3 CB3-1 1 CB2-3 3 CB2-1 1 CB1-3 CB1-1 3 1 CB5 30A 126130 CB4 20A 126128 CB3 30A 126130 CB2 20A 126128 CB1 25A 126129 L L N N GND GND-2 4 CB5-4 TCMA-5L2 2 CB5-2 TCMA-5L1 4 CB4-4 TCMH-5L2 2 CB
SW3 -4 WH ITE GND-2 NEMA L6-20P NEMA L6-30P NEMA L6-20P 3 1 3 SW2-1 SW3 -3 SW3 -1 SW2-3 GND-2 TCMH 255774 2 3 GND-2 TCMA-3L1 26 6 TCMA-3L2 TCMH-6 6 TCMB-6 WHITE TCMA-5L2 GND-2 TCMA-5L1 BLACK TCMA-5L1 126511 3 TCMH-3L1 2 Cable 125789 TCMH-3L2 TCMB 255774 WHITE 6 BLACK 6 125357 SW2-1 TCMB -3L2 SW3-3 SW1-3 SW3-1 SW1-1 SW2-3 WHITE 5 TCMB -3L1 TCMB-5L2 GND-2 TCMB-5L1 BLACK 126511 SW3 Switch -15U423 1 TCMB-5L1 4 2 4 2 TCMA-5L2 A FLU ID HEATER 5.
Electrical Schematics Page 3 of 3 5 FCM1 7 Base - 289697 FCM - 289696 1 121806 126495 2 121806 126496 126494 16T072 DISPLAY SHIELD 15M483 DISPLAY FRONT 255727 3 1 AFCM 255920 2 15M976 4 5 5 3A2989G Dose B Motor B 15U542 121683 B Tank RTD 126381 121683 Reed Switch Manifold 256555 15M977 3 15U542 4 A Tank RTD 126381 Linear Sensor - 256893 USB Stop - 121619 15M669 Air Motor Junction Box NXT411 15M974 15M669 15M975 1 15M977 2 127172 B GREEN A LEVEL SENSOR 24T052 15R324 15V7
1” 6\VWHP 9DOYH 30 $872 PLFURQ { ರ SVL OLPLW )OXVK 3XPS (;+ 3XPS 5HJ 7R +RVH &LUF 3XPS SVL OLPLW 0LFURQ )LOWHU 5HJ 7R % )HHG 0RGXOH 7R $ )HHG 0RGXOH 0DLQ FRQWURO YDOYH -XQFWLRQ %R[ 6ROHQRLGV ;0 &RQWURO %R[ 6ROHQRLGV 7R 3QHXPDWLF 5DP SXPS SLORW % 7R 3QHXPDWLF 5DP SXPS SLORW $ SVL OLPLW (;+ 'RVLQJ 9DOYHV ;0 'XDO SLORW YDOYH 3803 $ +LJK 3UHVVXUH 0HWHULQJ 3XPSV 3803 % Electrical Schematics XM PFP Air Logic Schematic 3A2989G
3A2989G ~ 7XEH 3UHV 5HOLHI 9DOYH 6SHHG &RQWURO $JLWDWRU 0RWRU /XEULFDWRU :DWHU 3XPS 7DQN +HDW ~ 5HG KRVH 9HQW $LU )URP 3URSRUWLRQHU ೀ5HG KRVH 7DQN /LG 0DQLIROG ~ 5HG KRVH 7DQN 3UHVVXUH 21 2)) 21 2)) &LUF $JLWDWRU ~ 5HG KRVH 2SWLRQDO 7DQN 'U\ $LU 5HG KRVH $LU 0RWRU $JLWDWRU 6SHHG &RQWURO 3XPS 2YHULGH 3XVK %XWWRQ ~ 5HG KRVH %ODFN From J-Box Level Solenoid %ODFN %ODFN 5$0 3DLO )HHG 3XPS 35(6685( 5(*8/$725 '2:1 83 ~ :KLWH 3DLO %ORZ RII 'U\ $LU WR WDQN L
Parts Parts XM PFP System (262869, 24W626) Ref. Part 1 262878 24W648 2 24P202 24W628 2a 24P883 2b* C20461 2c‡ 100505 2d‡ 156849 2f◆ 15U654 Description Qty. SYSTEM MODULE AND MIX LINE 1 Model 262869 Model 24W626 FEED MODULES ASSEMBLY 1 Model 262869 Model 24W626 FEED MODULE 2 NIPPLE, reducing 1 BUSHING 1 NIPPLE 1 LABEL, A/B Identification 1 Ref. Part 2g◆ 061134 2h◆ --3 16T121 16T122 Description HOSE, nylon CABLE TIE HEATED HOSE BUNDLE Model 262869 Model 24W626 Qty. 2.5 8 1 --- Not for sale. ◆ Not shown.
Parts XM PFP System (262869, 24W626) Subassemblies Base System (262878, 24W648) Page 1 of 5 46 85 95 96 61 97 99 98 61 ti20154a Heated Hose Bundle 16T121. Not included with assemblies 262878 and 262869. Shown for reference only. Heated Hose Bundle 16T122 not included with assembly 24W648 and 24W626. Shown for reference only. NOTE: Apply pipe sealant to all non-swiveling pipe threads.
Parts Base System (262878, 24W648) page 2 of 5 Set air regulator to 85 psi (590 kPa, 5.
Parts Base System (262878, 24W648) page 3 of 5 29 28 56 27 37 85 36 55 31 54 67 60 118 105 67 59 120 ti20157a 3A2989G 35
Parts Base System (262878, 24W648) page 4 of 5 133 110 109 132 17 86 16 15 19 112 116 111 115 52 117 40 108 114 9 113 23 114 25 26 21 20 17 36 22 24 ti20158b 18 3A2989G
Parts Base System (262878, 24W648) page 5 of 5 78 79 127 120 12 9 54 132 107 133 87 15 106 64 13 93 100 34 82 100 85 ti20159b 54 12 3A2989G 37
Parts Base System (262878, 24W648) Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 38 Part Description Qty --FRAME 1 L180C9 PUMP; B side lower 1 L220C9 PUMP; A side lower 1 100133 WASHER, lock, 3/8 8 100101 SCREW, cap, hex head 8 256169 PLATE, solvent pump 1 121488 SCREW, hex head, flanged 2 W30CAS PUMP, solvent, 6.
Parts Ref Part Description Qty 85◆ H75002 HOSE, coupled, 7250 psi, 0.5 in. 2 (12 mm) ID, 2 ft 86 --TUBE, 0.375 in. (9.5mm) ID blue 6 nylon 87 --TUBE, 0.375 in. (12 mm) ID red 1.5 nylon 88 114601 CONDUIT, flexible, non-metallic 3.5 92 15T258 TOOL, wrench, Xtreme, 145/290 1 93 24P242 SENSOR, RTD, 1k ohm, insulated 1 94 158586 FITTING, bushing 1 95◆ 16T316 MIXER, static, assembly 1 96◆ H75010 HOSE, coupled, 7250 psi, 0.50 ID, 1 10 ft 97◆ H73803 HOSE, coupled, 7250 psi, 0.
Parts Feed Module (24P883) Page 1 of 2 298 217 246 243 297 213 219 212 201 213 219 273 211 218 267 209 215 266 265 268, 215 219a 272 208 202 207 300 247 210 216 269 254 230 270 213 211 253 233 206 254 271 252 251 252 220 40 222 WL F Turns clockwise as viewed from the top 3A2989G
Parts Page 2 of 2 259 260 261 223 227 258 257 231 262 224 225 227a 224 250 213 249 250 227c 226 229 277 228 224 276 227b ti20161c 3A2989G 41
Parts Feed Module (24P883) Ref 201 202 203 Part --24M683 --- 204 205 111841 --- 206 207 16R869 --- 208 126351 209 126381 210 211 212 213 215 216 126898 295847 16T481 157785 171988 16T619 217 24P885 218 --- 219 220 221 222 223 224 225 226 227◆ 24T052 D11021 100016 102040 262860 113796 16R871 16T525 262868 227a P40DCS 227b 227c 228 229 230 231 232 233 234 257620 257727 GC2041 100017 117426 104633 --103475 --- 235 --- 236 237 238 239 240 241 242 243 246 205418 109130 16P244 15B772 05417
Parts Heated Hose Bundle 16T121 - 3/4 in. x 1/2 in. (included in model 262869) 16T122 - 3/4 in. x 3/4 in. (included in model 24W626) 305 (blue) 308 305 310b 310c 304 302 (red) 303 309 307 301 303 302 310a 306 ti20243a Ref 301 Part Description Qty H67550 HOSE, coupled, 3/4 in., 6500 psi; Model 16T121 - Qty 1 Model 16T122 - Qty 2 302 16X027 KIT, tube, 0.375 (9.5mm) ID red 2 nylon 303 H42550 HOSE, coupled, 4500 psi, 1/4 in. ID, 1 50 ft (15.
Parts Base System (262878, 24W648) Subassemblies System Air Controls Module (255761) NOTE: For Feed Module Air Panel (262860) parts, see page 55. 616 617 644 607 608 613 610 603 611 609 Ref. 27 615 645 642 626 619 637 636 638 632 629 612 632 613 635 617 646 643 618 628 630 627 640 631 Ref.
Parts Junction Box (24N598) 403, 446 412 402 403 418, 419, 423 411 4 413, 414, 443 404 415, 445 416 442 B HOSE A 422, 439 417, 444 405 405a ti20155a 407, 408 405b 405f 405c 405e 406 403 407 420 421 425 442 426, 427 409 410 401 4 Set High Power Temperature Control Module zone addresses on dial under cover when installing modules (404). Addresses: B Module =1, Hose Module = 2, A Module = 0. NOTE: See Electrical Schematics beginning on page 27 for cable identification.
Parts Junction Box (24N598) Ref 401 402 403 404◆ 405 405a 405b 405c 405d 405e 405f 406 407 Part ----114231 255774 --126382 126129 126130 126684 126453 126128 121603 255047 408 255048 409 15U423 410 123967 411 123968 412 123969 413† 289697 414 104371 415z† 289696 416 117666 417 115942 418 15U651 419 117831 420 --421 109466 422 104387 423 113161 425 126496 426 426a 426b 426c 427 428 --121636 15A798 15A799 106084 125789 429 123422 430 121615 432 433 434 435 436 437 438 126495 124273 --126494 121806 -
Parts Control Box (255771) 543 532 538 539 504b 504f 501 504h 504e 551 536 502 523 521 504g 532 504c 538 537 504a, 504d 545 540 508 541 520 522 535 543 502 526 526 544 530 527 507 542 503 501 543 529 509 528 514 515 510 517 542 533 534 526 524, 525 546 519c ti18050a Ref.
Parts Ref. Part 519z 257088 519a 289899 z519b 289900 519c 277674 520 121618 521 15R324 522 121619 523 121617 523a❄ 123412 524 117745 525 117625 526 113505 527 15B090 528 --529 15R343 530 --531❄ 172953 532 120493 533 15H189 534 15G816 535 110637 536 15R325 537 538 539 540 541 542 543 544 545 546 551▲ 552❄ 120494 120495 15M974 15M975 15M976 15M977 121988 195875 102063 15U542 15X214 15X393 122829 Description MODULE, USB, assy.
Parts Air Filter (24P899) 706 707 711 705 711 704 702 703 701 702 703 1 Apply PTFE tape and/or pipe sealant to all non-swiveling pipe threads. 2 Orient fittings approximately as shown.
Parts Ratio Control Valve Assemblies 1 852 1 854 1 836 801 1 852 836 1 837 1 8 15 1 855 840 1 1 853 839 857 1 14 831 8 832 858 8 833 851 Apply pipe sealant to all non-swiveling pipe threads. 8 Position valve (832) with barbed fitting (833) oriented as shown, position elbow (837) as shown. ti20219a 14 Torque until nut (831) bottoms out in housing. 15 Flip ball valve handle retainer (855). Handle to face forward in open position.
Parts Feed Module (24P883) Sub-Assemblies Air Powered Agitator (24P885) 917 5 925 915 924 923 5 916 7 907 912 3 4 915 3 914 913 922 2 919 918 2 921 5 911 7 5 910 7 909 905 908 3 913 906 905 904 8 903 902 7 901 1 Apply pipe sealant to all non-swiveling pipe threads. 2 Apply low strength threadlocker. 3 Apply blue thread locker. 4 Remove four screws from gear reducer (915), pass them through bracket (912) and back into gear reducer (915) then torque to 150-170 in-lb (17-19 N•m).
Parts Air Powered Agitator (24P885) Ref 901 902 903 Part 16P919 16U219 --- 904 905 --122774 906 907 16P920 --- 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929▲ 930▲ 112222 --122761 122760 16P922 C19209 101682 181794 16P923 100828 16T063 116940 181849 101118 111310 115841 206264 191872 ------15A722 16A614 Description Qty SHAFT, agitator, upper 1 HOUSING, agitator 1 SEAL, 0.875 in. ID x 1.125 in.
Parts Tank Air Manifold Assembly 1008 1010 1012 1011 1001 1004 1002 1013 1005 1003 1009 1008 1013 1003 Ref 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 Part 189016 155665 156849 214847 165198 100840 103347 156971 108638 101759 101754 100139 100030 111856 --- 1007 1006 1 Apply pipe sealant to all non-swiveling pipe threads. 2 Orient all fittings as shown.
Parts Static Mixer (16T316) 1303 1301 1303 1302 1 Ref 1301 1302 1303 Part --24P886 16T315 1304 --- Apply pipe sealant to all non-swiveling pipe threads. Description Qty TUBE, mixer 1 MIXER, 12 element, stainless steel 1 BUSHING, reducing 3/4 nptf x 2 1/2 npt SEALANT, pipe, stainless steel 1 --- Not for sale.
Parts Feed Module Air Panel (262860) NOTE: For System Air Controls Module (255761) parts, see page 44. 1102 1103 1101 1123 1122 1103 1113 1114 1121 1104 1122 1128 1121 1109 1111 1120 1119 1118 1122 1116 1115 1117 1129 1130 1105 1106 1127 1125 1111 1113 1110 1114 1 3A2989G Apply pipe sealant to all non-swiveling pipe threads.
Parts Air Panel (262860) Ref 1101 1102 1103 Part ----121424 1104 15T498 1105 1106 116513 121141 1109 1110 1111 1113 1114 1115 1116 1117 1118 1119 198171 100403 121457 155699 165198 104984 157705 156971 206264 114367 1120 1121 1122 1123 1124 1125 109544 110914 100264 116514 109193 16F151 1126 1127 1128 1129 1130 --054134 517305 106495 100840 Description BRACKET, air control LABEL, instructions GAUGE, pressure, panel mount, 1.5 in. FITTING, 90 degree, swivel, 5/32 in. tee x 1/8 in.
Parts Check Valve (16T481) Flexible Fluid Connection Kit (262820) 1412 1411 1401 1402 1404 1410 1205 1202 1407 1403 1404 1402 1405 1406 1206 1408 1207 1204 1203 1201 1 1 Ref 1201 1202 1203 1204 1205 1206 1207 1409 Torque to 75-80 ft-lb (102-108 N•m). Part --102595 100279 108361 --181492 181535 --- Not for sale.
Technical Data Technical Data XM PFP Mix Ratio Range Ratio Tolerance Range (before alarm) Maximum Flow Rate (measured with oil) Fluid Viscosity Range US Metric 1:1-10:1 (in 0.01 increments) +/- 5% 3 gallons per minute 13.6 liters per minute Handles mastic materials which are loaded into heated tanks with ram-fed priming piston pumps Air Inlet 1 in.
Technical Data XM PFP US Wetted Parts Suction Tube (Flush) Tanks Flush Pump Hoses Pumps (A, B and Feed Pail) Dosing Valves Manifold Metric Aluminum Stainless Steel Carbide, PTFE, stainless steel, UHMWPE Nylon Carbon steel, alloy steel, 303, 440, 17-ph grades stainless steel, zinc and nickel plating, ductile iron, tungsten carbide, PTFE Carbon Steel, nickel plating, carbide, polyethylene, leather Carbon steel, nickel plating, carbide, 302 stainless steel, PTFE, UHMWPE Stainless steel housing with stainle
Technical Data Dimensions Min: 70 in. (1780 mm) Max: 84 in. (2130 mm) 76 in. (1930 mm) 52 in. (1320 mm) Min: 70 in. (1780 mm) Max: 84 in. (3130 mm) 104 in. (2640 mm) 38 in.
Notes Notes 3A2989G 61
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
