Please send other correspondence to: Graco Children’s Products Inc. Main Street P.O. Box 100 Elverson, PA 19520-0100 238 A IMPORTANT! PRODUCT REGISTRATION CARD THANK YOU FOR CHOOSING !802010040401! PRODUCT REGISTRATION DEPARTMENT PO BOX 40 DENVER CO 80201-0040 Stroller Owner’s Manual Please save for future use.
✃ Failure to follow these warnings and the assembly instructions could result in serious injury or death. MISE EN GARDE Manquer de suivre ces avertissements et les instructions d'assemblage peut entraîner de sérieuses blessures ou un décès. NEVER LEAVE child unattended. Always keep child in view while in stroller. NE LAISSEZ JAMAIS votre enfant sans surveillance. Ayez toujours l’enfant en vue. AVOID FINGER ENTRAPMENT: Use care when folding and unfolding the stroller.
WARNING NEVER PLACE child in the stroller with head toward front of stroller. NEVER ALLOW YOUR STROLLER to be used as a toy. STROLLER TO BE USED only at walking speed. Product not intended for use while jogging, skating, etc. DISCONTINUE USING YOUR STROLLER should it become damaged or broken. MISE EN GARDE NE JAMAIS PLACER l’enfant dans la poussette avec la tête vers l’avant de la poussette. NUNCA COLOQUE el niño en el cochecito con la cabeza en la delantera parte del cochecito.
Questions? Des questions? ¿Preguntas? Replacement Parts (USA) Piezas de repuesto (EE.UU) In the U.S.A. or Canada, please contact our Customer Service Department with any questions you may have concerning parts, use, or maintenance. When you contact us, please have your product’s model and serial numbers ready so that we may help you efficiently.
46 Pull straps back through seat slots. Straps remain attached to frame. Modèles avec harnais: au moment de l'enlever, tirez les courroies aux épaules à travers le panneau du dossier. Tirez les courroies à travers les fentes du siège. Les courroies restent attachées à l'armature. Modelos con arnés: Para quitar las correas de los hombros, páselas a través del tablero. Pase las correas por las ranuras del asiento. Las correas se mantienen fijas al bastidor.
Basket Le panier La canasta 4 To Remove Seat 39 5 Enlever le siège Para sacar el asiento 40 41 SNAP! ENCLENCHEZ! ¡CHASQUIDO! Four plastic tabs under seat front. Holes and metal buttons on underside Seven snaps Trous et boutons métallique en dessous Sept boutons-pression Agujeros y botones metálicos por debajo Siete broches Footrest and Front Wheels Close canopy, if it is open, and turn stroller over.
37 Push carrier down so it is below latches on stroller handle as shown. Turn and lock latches. ALWAYS LOCK LATCHES OVER CARRIER. Check that carrier is securely attached by pulling up on the carrier handle. Appuyez sur le porte-bébé vers le bas pour qu’il soit en-dessous des loquets de sûreté sur le guidon de la poussette comme illustré. Tournez et verrouillez les loquets de sûreté. TOUJOURS VERROUILLEZ LES LOQUETS DE SÛRETÉ AU-DESSUS DU PORTE-BÉBÉ.
Child’s Tray Le plateau pour enfant 10 La bandeja del niño 11 13 12 14 To Attach Graco® Infant Carrier (sold separately) Attacher le porte-bébé Graco® (vendu séparément) Instalación del transportador Graco® (vendido por separado) WARNING Improper use of this stroller with a carrier may result in serious injury or death. Use a Graco infant carrier only. Read the manual provided with your Graco carrier before using it with your stroller.
To Adjust Handle Pour ajuster le guidon 32 Para ajustar la manija Choose from three handle positions or flip all the way down for storage. Choisissez une des trois positions du guidon ou abaissez complètement pour le rangement. Elija una de las tres posiciones para la manija o bájela completamente para almacenar. To Fold Stroller Plier la poussette Para plegar el cochecito Before folding stroller: 1) lock front swivel wheels, 2) adjust seat back to upright position and 3) apply brakes.
Attacher le baldaquin To Secure Canopy 19 Para poner la capota 20 Sun visor is included on certain models. To Use Brakes 26 Pour utiliser les freins 27 WARNING Always apply both brakes. Check brakes by trying to push stroller. Un pare-soleil est inclus sur certains modèles. MISE EN GARDE Toujours utiliser les deux freins. Vérifiez les freins en essayant de pousser la poussette. En ciertos modelos, la visera incluida.
Attacher le baldaquin To Secure Canopy 19 Para poner la capota 20 Sun visor is included on certain models. To Use Brakes 26 Pour utiliser les freins 27 WARNING Always apply both brakes. Check brakes by trying to push stroller. Un pare-soleil est inclus sur certains modèles. MISE EN GARDE Toujours utiliser les deux freins. Vérifiez les freins en essayant de pousser la poussette. En ciertos modelos, la visera incluida.
To Adjust Handle Pour ajuster le guidon 32 Para ajustar la manija Choose from three handle positions or flip all the way down for storage. Choisissez une des trois positions du guidon ou abaissez complètement pour le rangement. Elija una de las tres posiciones para la manija o bájela completamente para almacenar. To Fold Stroller Plier la poussette Para plegar el cochecito Before folding stroller: 1) lock front swivel wheels, 2) adjust seat back to upright position and 3) apply brakes.
Child’s Tray Le plateau pour enfant 10 La bandeja del niño 11 13 12 14 To Attach Graco® Infant Carrier (sold separately) Attacher le porte-bébé Graco® (vendu séparément) Instalación del transportador Graco® (vendido por separado) WARNING Improper use of this stroller with a carrier may result in serious injury or death. Use a Graco infant carrier only. Read the manual provided with your Graco carrier before using it with your stroller.
37 Push carrier down so it is below latches on stroller handle as shown. Turn and lock latches. ALWAYS LOCK LATCHES OVER CARRIER. Check that carrier is securely attached by pulling up on the carrier handle. Appuyez sur le porte-bébé vers le bas pour qu’il soit en-dessous des loquets de sûreté sur le guidon de la poussette comme illustré. Tournez et verrouillez les loquets de sûreté. TOUJOURS VERROUILLEZ LES LOQUETS DE SÛRETÉ AU-DESSUS DU PORTE-BÉBÉ.
Basket Le panier La canasta 4 To Remove Seat 39 5 Enlever le siège Para sacar el asiento 40 41 SNAP! ENCLENCHEZ! ¡CHASQUIDO! Four plastic tabs under seat front. Holes and metal buttons on underside Seven snaps Trous et boutons métallique en dessous Sept boutons-pression Agujeros y botones metálicos por debajo Siete broches Footrest and Front Wheels Close canopy, if it is open, and turn stroller over.
46 Pull straps back through seat slots. Straps remain attached to frame. Modèles avec harnais: au moment de l'enlever, tirez les courroies aux épaules à travers le panneau du dossier. Tirez les courroies à travers les fentes du siège. Les courroies restent attachées à l'armature. Modelos con arnés: Para quitar las correas de los hombros, páselas a través del tablero. Pase las correas por las ranuras del asiento. Las correas se mantienen fijas al bastidor.
Questions? Des questions? ¿Preguntas? Replacement Parts (USA) Piezas de repuesto (EE.UU) In the U.S.A. or Canada, please contact our Customer Service Department with any questions you may have concerning parts, use, or maintenance. When you contact us, please have your product’s model and serial numbers ready so that we may help you efficiently.
Please send other correspondence to: Graco Children’s Products Inc. Main Street P.O. Box 100 Elverson, PA 19520-0100 238 A IMPORTANT! PRODUCT REGISTRATION CARD THANK YOU FOR CHOOSING !802010040401! PRODUCT REGISTRATION DEPARTMENT PO BOX 40 DENVER CO 80201-0040 Stroller Owner’s Manual Please save for future use.
✃ Failure to follow these warnings and the assembly instructions could result in serious injury or death. MISE EN GARDE Manquer de suivre ces avertissements et les instructions d'assemblage peut entraîner de sérieuses blessures ou un décès. NEVER LEAVE child unattended. Always keep child in view while in stroller. NE LAISSEZ JAMAIS votre enfant sans surveillance. Ayez toujours l’enfant en vue. AVOID FINGER ENTRAPMENT: Use care when folding and unfolding the stroller.
Infant Restraint/Carrier Owner’s Manual READ THIS MANUAL KEEP INSTRUCTIONS FOR FUTURE USE. Do not install or use this infant restraint until you read and understand the instructions in this manual. FAILURE TO PROPERLY USE THIS INFANT RESTRAINT INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN A SUDDEN STOP OR CRASH.
1.0 Registration Information . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5 1.1 Register Your Infant Restraint . . . . . . . . . . . . . . . . . . . . . .4 1.2 Recall Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.3 If You Need Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2.0 Features and Components . . . . . . . . . . . . . . . . . . . . . . . .6-13 2.1 3-Point Harness Model . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.
5.0 Using Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-36 5.1 Positioning Harness Straps . . . . . . . . . . . . . . . . . . . . . . .24 5.1.1 3-Point Harness . . . . . . . . . . . . . . . . . . . . . . . . . .25 5.1.2 5-Point Harness . . . . . . . . . . . . . . . . . . . . . . . . . .26 5.2 Securing Child in Infant Restraint . . . . . . . . . . . . . . . . . .28 5.2.1 3-Point Harness . . . . . . . . . . . . . . . . . . . . . . . . . .29 5.2.2 5-Point Harness . . . . . .
1.0 Registration Information Model Number: Serial Number: Purchase Date: 1.1 Register Your Infant Restraint Please fill in the above information. The model and serial numbers can be found on a label underneath your infant restraint. Fill out the prepaid registration postcard attached to the seat cover and mail it today. Child restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall.
1.3 If You Need Help In the U.S.A. or Canada, please contact our Customer Service Department with any questions you may have concerning parts, use, or maintenance. When you contact us, please have your product’s model and serial numbers ready so that we may help you efficiently. These numbers can be found on a sticker on the underside of your infant restraint. USA: 1-888-224-6549 or www.gracobaby.
2.0 Features and Components Each model of the infant restraint comes with different harness options. To adjust your infant restraint properly, it is very important to follow the instructions that are appropriate for the model you have purchased.
2.
REAR VIEW: 3-POINT HARNESS Canopy Harness tightener Release handle Level indicator* Harness anchor buckle Harness slot Mounting notch Attachment latch Owner’s manual pocket Locking clip** *Level Indicator The level indicator is attached to the side of the infant restraint, and indicates whether or not the infant restraint is properly reclined. **Locking Clip The locking clip is stored on the bottom of the infant restraint. You will need to use it with certain types of vehicle seat belts.
2.
REAR VIEW: 5-POINT HARNESS Canopy Release handle Mounting notch Level indicator* Harness slot Owner’s manual pocket Attachment latch Metal junction plate Waist strap anchor buckle Harness adjustment strap Locking clip** *Level Indicator The level indicator is attached to the side of the infant restraint, and indicates whether or not the infant restraint is properly reclined. **Locking Clip The locking clip is stored on the bottom of the infant restraint.
2.3 Removing and Attaching Base To remove infant restraint, squeeze handle at back of seat and lift infant restraint from base as shown . To put infant restraint in base, push infant restraint down until it clicks into base. Pull up on infant restraint to be sure it is latched firmly into base. 2.4 Adjusting Handle 1. Press handle adjustment buttons on both sides of handle . 2. Rotate handle until it clicks into any of three positions (for carrying, reclining, or sitting).
2.5 Attaching Canopy 1. Infant restraint comes with four (two on certain models) identical canopy support parts. Thread one canopy support completely through one sewn tunnel . 2. Slide straight end of a second support into the straight end of the first support . 3. On models with four canopy supports, repeat steps one and two for the other canopy tunnel. The canopy should appear as shown . 4. Attach canopy in the areas between the infant restraint and the handle base .
2.6 Head Support (on certain models) Some infants may need extra support to keep their head and body in a comfortable position. Unsnap the sides and resnap them with the harness straps threaded through the slots in the cushion . If your model does not include a head support, you may want to use a rolled towel or a blanket for support . MAKE SURE THAT NOTHING INTERFERES WITH THE HARNESS. It must still be flat and snug against your child’s shoulders. 2.
3.0 Important Information 3.1 Warnings for Use as Infant Restraint • DO NOT INSTALL OR USE THIS INFANT RESTRAINT AND BASE UNTIL YOU READ AND UNDERSTAND THE INSTRUCTIONS IN THIS MANUAL AND IN YOUR VEHICLE OWNER’S MANUAL. DO NOT let others install or use the infant restraint unless they understand how to use it. • FAILURE TO PROPERLY USE THIS INFANT RESTRAINT AND BASE INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN A SUDDEN STOP OR CRASH.
• SOME SPECIAL NEEDS CHILDREN, such as pre-term babies or those who have tested positive for positional apnea, may be at increased risk of suffering breathing or other difficulties in an infant restraint. If your child has special needs, we recommend that you have your physician or hospital staff evaluate your child and recommend the proper infant restraint or car bed before using this product.
• NEVER USE INFANT RESTRAINT AND BASE IF IT HAS DAMAGED OR MISSING PARTS. DO NOT use a cut, frayed or damaged infant restraint harness or vehicle seat belt. • THE INFANT RESTRAINT CAN BECOME VERY HOT IF LEFT IN THE SUN. Always touch the surface of any metal or plastic parts before putting your child in the infant restraint. • THIS CHILD RESTRAINT CONFORMS to all applicable Federal Motor Vehicle Safety Standards and is certified for use in motor vehicles and aircraft.
3.3 Additional Warnings for Use as Carrier • FALL HAZARD: Child’s movements can slide carrier. NEVER place carrier near edges of countertops, tables or other high surfaces. Always stay within arms reach whenever carrier is not on floor/ground. BE SURE handle locks into position before lifting carrier. NEVER place carrier in the top of a shopping cart. • SUFFOCATION HAZARD: Infant Carrier can roll over on soft surfaces and suffocate child. Never place carrier on beds, sofas or other soft surfaces.
3.4 Height and Weight Limits FAILURE TO USE INFANT RESTRAINT IN A MANNER APPROPRIATE FOR YOUR CHILD’S SIZE MAY INCREASE THE RISK OF SERIOUS INJURY OR DEATH. Your child MUST meet all requirements: • WEIGHT: 20 lbs.
4.0 Infant Restraint Location 4.1 Vehicle Seat Requirements IMPROPER PLACEMENT OF THE INFANT RESTRAINT INCREASES THE RISK OF SERIOUS INJURY OR DEATH. Some seating positions in your vehicle may not be safe for this infant restraint. Some vehicles do not have any seating positions that can be used safely with the infant restraint. If you are not sure where to place the infant restraint in your vehicle, consult your vehicle owner’s manual or Graco Children's Products Inc., 1-888-224-6549.
• The VEHICLE seat must face forward. • DO NOT use infant restraint on vehicle seats with seat backs that will not lock in an upright position. DO NOT use seats that can fold down without having to release a lock or latch of some kind. These seats can fly forward and strike the child in a sudden stop or crash. 4.2 Vehicle Seat Belt Requirements MANY SEAT BELT SYSTEMS ARE NOT SAFE TO USE WITH THE INFANT RESTRAINT. THE VEHICLE SEAT BELT MUST BE DESIGNED TO HOLD THE INFANT RESTRAINT TIGHTLY AT ALL TIMES.
4.2.1 UNSAFE Vehicle Belt Systems DO NOT use any of the following systems to secure the infant restraint. • Lap Belts with Emergency Locking Retractor (ELR) This lap belt stays loose and can move until it locks in a crash or sudden stop. • Combination Lap/Shoulder Belt with Retractor Each strap has a retractor at one end and is attached to the latch plate at the other end.
4.2.2 SAFE Vehicle Belt Systems THE FOLLOWING BELT SYSTEMS CAN BE USED WITH YOUR INFANT RESTRAINT, IF the seat location meets all other requirements of these instructions and those in your vehicle owner's manual. • Lap Belts - Manually Adjusted When buckled, the belt is tightened manually by pulling on the excess belt while pushing down hard on the infant restraint. • Lap Belts with Automatic Locking Retractor (ALR) The automatic locking retractor will not permit the lap belt to lengthen once it is buckled.
• Combination Lap/Shoulder Belt with Sliding Latch Plate This belt has a latchplate that slides freely along the belt. This belt MUST be converted to prevent movement of the lap portion of the belt. You must use the locking clip provided with the infant restraint, unless your vehicle's seat belt Locking clip can be converted in another way as described in your vehicle owner's manual. To Install Locking Clip: 1.
5.0 Using Infant Restraint 5.1 Positioning Harness Straps FAILURE TO PROPERLY ADJUST THE HARNESS STRAPS FOR YOUR CHILD INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN THE EVENT OF A SHARP TURN, SUDDEN STOP OR CRASH. The harness straps must be properly adjusted to fit your child according to the following instructions. 1. Remove infant restraint from base and rotate handle down to sitting position. See “2.3 Removing and Attaching Base” and “2.4 Adjusting Handle”, p. 11. 2.
5.1.1 3-Point Harness 1. From back, push harness anchor buckle back through harness slot. If necessary, from front, use harness strap to pull buckle from slot . Harness tightener 2. Reinsert harness anchor buckle in the appropriate slot . Harness anchor buckle 3. From back, remove harness strap from harness tightener. If necessary, from front, use harness strap to pull strap from slot. 4. Reinsert strap in the appropriate slot. Thread strap through tightener exactly as shown . 5.
5.1.2 5-Point Harness 1. Depress the harness adjustment button under the seat flap . Pull the shoulder straps out to loosen the harness . 2. Behind seat, remove the ends of the two shoulder straps from the metal junction plate . 3. From front, pull straps through the harness slots and then reinsert them Harness adjustment button through the appropriate slots. 4. Behind seat, push both shoulder straps UNDER owner’s manual pocket and out the bottom. 5.
FOR SMALLER BABY: Use the lower harness slots (if they are even with or just below your child’s shoulders) and the upper strap loops . The ends of the straps must hang in front of the metal plate as shown in , not as shown in . CHECK that the loops are completely within junction plate slots . CHECK that straps are secure by pulling on them. FOR LARGER BABY: Use upper harness slots and the end strap loops . CHECK that the loops are completely within junction plate slots .
5.2 Securing Child in Infant Restraint Failure to properly secure your child in the infant restraint/carrier increases the risk of serious injury or death from suffocation or falls, or in the event of a sudden stop or crash. Even when used only as a carrier, make sure the harness straps are properly secured. 1. Move infant restraint handle to sitting position (see page 11). 2. Open harness clip by squeezing both sides and unbuckle as shown . OR 3.
5.2.1 3-Point Harness 5. Buckle harness to the latch between child’s legs. Make sure that you hear a “click.” DO NOT use the infant restraint if the harness does not latch in place. Call Graco at 1-888-224-6549. 6. From the back, pull strap through harness tightener to tighten the straps as shown . CHECK that both straps are flat and tight on child’s shoulders. 7. Snap harness clip pieces together . Position harness clip in middle of chest, level with armpits and away from the neck . 8.
5.2.2 5-Point Harness 5. Insert the two buckle tongues into the harness buckle on the crotch strap. Make sure that you hear each tongue click into the buckle. DO NOT use the infant restraint if the harness does not latch in place. Call Graco at 1-888-224-6549. 6. Snap harness clip pieces together . 7. Pull on harness adjustment strap to tighten straps as shown . CHECK that both straps are flat and tight on shoulders. 8. Position harness clip in middle of chest, level with armpits and away from the neck .
5.3 Installing the Infant Restraint/Base You must carefully follow the instructions provided by your vehicle manufacturer, in addition to the information in this manual. Be sure you have read and understood section 4, “Infant Restraint Location” on p.19-23. Make sure vehicle is on level ground so that the level indicator, which is attached to the infant restraint, can be used to properly recline the infant restraint .
3. Thread the seat belt: Base and infant restraint Infant restraint only Belt MUST go under tongue 4. Buckle the seat belt. Make sure the buckle tongue goes into the correct buckle . The seat belt should not be twisted or turned. 5. Tighten the vehicle seat belt. Refer to your vehicle owners manuel and the instructions in “4.2.2 SAFE Vehicle Belt Systems”, p. 22-23, on tightening your vehicle belt.
6. Push the infant restraint down into the base and make sure that you hear a “click” . Pull up on the infant restraint to be sure it is latched securely into the base. If the infant restraint does not securely latch into the base, the infant restraint provides NO protection for your child. DO NOT use the infant restraint/base if the infant restraint does not securely latch into the base.
5.4 Reclining Infant Restraint/Base For your child’s safety, it is important that your infant restraint/base be properly reclined. Attached to the side of your infant restraint is a level indicator to help properly recline the infant restraint/base on the vehicle seat. Failure to properly recline the infant restraint on the vehicle seat increases the risk of serious injury or death. If the infant restraint is too upright, a child’s head may drop forward and cause breathing problems.
When using the base: To lower the foot; pull down on the bottom of the foot to the desired setting to adjust the recline . To raise the foot; set the base on a flat surface, push in on the fingers on the base and push down on the base to adjust the recline . If there is still orange in the level indicator when the foot is completely extended then place a rolled towel under the foot until ONLY blue shows .
Final Safety Check: Every time you drive with your child, PUSH DOWN on the top of the infant restraint slowly but firmly to make sure the vehicle belt does not lengthen at all and that the vehicle belt is fastened very tightly around the infant restraint/base . Holding the infant restraint near the vehicle belt path, TWIST AND PULL the seat forward and to both sides to make sure the vehicle belt does not lengthen or loosen and the infant restraint does not easily move .
6.0 Additional Information 6.1 Airplane Use Install in an airplane the same way as in an automobile. Notify the airline ahead of time that you intend to bring the seat on board. Use only in forward-facing aircraft seat. Follow the flight attendant’s instructions about infant restraint placement. Do not use this infant restraint if the airplane seat belt does not hold the infant restraint tightly. 6.2 Cleaning and Maintenance TO REMOVE AND WASH INFANT RESTRAINT PAD, follow instructions in “5.
Reverse steps to reinstall seat pad. Check that harness system is not twisted, and pull on harness system to be sure harness is securely reinstalled. INFANT RESTRAINT METAL AND PLASTIC PARTS may be cleaned by wiping with a mild soap and water solution. DO NOT USE BLEACH. Use of bleach may weaken plastic parts. HARNESS STRAPS may be spot cleaned or replaced. DO NOT IMMERSE THE HARNESS STRAPS IN WATER. Doing so may weaken the harness straps. BUCKLE may be cleaned with a damp cloth.
Notes: 39
How to Order: Complete the form that follows. Your infant restraint model and serial numbers MUST be included on the form to ensure proper replacement parts. Your model number can be found on a sticker on the underside of your infant restraint. Payment must accompany your order. Parts may also be ordered from Graco’s web site at www.gracobaby.com. Parts List: Price:** Seat pad ................................. $20.00 Canopy ................................... $17.00 Canopy bow ...........................
Model No. (Both Numbers Required) Serial No. SHIP TO: Subtotal: Name Shipping & handling*: $5.00 Sales tax**: Address Total: City, State, Zip Code * $15.00 outside the continental U.S. **CA 6%, IL 6.25%, IN 5%, NY 8.25%, OH 5.75%, PA 6%, SC 5% Telephone (including Area Code) Seat pad Canopy Canopy bow 3-point harness 5-point harness Harness clip Locking clip Head support Base Check or money order enclosed (payable to Graco Children’s Products Inc.
Asiento de seguridad infantil/ portabebés Manual del propietario LEA ESTE MANUAL GUARDE LAS INSTRUCCIONES PARA SU USO EN EL FUTURO. No instale ni use este asiento de seguridad infantil hasta que lea y entienda las instrucciones en este manual. EL USO INCORRECTO DE ESTE ASIENTO DE SEGURIDAD INFANTIL AUMENTA EL RIESGO DE LESIONES GRAVES O LA MUERTE EN UNA PARADA REPENTINA O UN ACCIDENTE.
1.0 Información de inscripción . . . . . . . . . . . . . . . . . . . . . . . . .4-5 1.1 Inscriba su asiento de seguridad infantil . . . . . . . . . . . . . .4 1.2 Información de retirada . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.3 Si necesita ayuda . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2.0 Características y componentes . . . . . . . . . . . . . . . . . . . .6-13 2.1 Modelo de correas de 3 puntos . . . . . . . . . . . . . . . . . . . . .7 2.
5.0 Usar el asiento de seguridad infantil . . . . . . . . . . . . . . . . . . .24-36 5.1 Posición de las correas . . . . . . . . . . . . . . . . . . . . . . . . . .24 5.1.1 Correas de 3 puntos . . . . . . . . . . . . . . . . . . . . . . .25 5.1.2 Correas de 5 puntos . . . . . . . . . . . . . . . . . . . . . . .26 5.2 Sujetar al niño en un asiento de seguridad infantil . . . . . .28 5.2.1 Correas de 3 puntos . . . . . . . . . . . . . . . . . . . . . . .29 5.2.2 Correas de 5 puntos . . . . . . . . . . . . . .
1.0 Información de inscripción Número de modelo: Número de serie: Fecha de compra: 1.1 Inscriba su asiento de seguridad infantil Complete la información arriba indicada. Los números de serie y modelo se pueden encontrar en la etiqueta debajo del asiento de seguridad infantil. Complete la tarjeta de inscripción con sello ya franqueado adjunta a la funda del asiento y envíela hoy por correo. Los asientos de seguridad infantil pueden retirarse del mercado por razones de seguridad.
1.3 Si necesita ayuda En los EE.UU. o Canadá, póngase en contacto con nuestro departamento de servicio al cliente con cualquier pregunta que tenga sobre piezas, uso o mantenimiento. Cuando nos llame, tenga a mano los números de modelo y serie de su producto para que le podamos atender de manera eficaz. Estos números se pueden encontrar en una etiqueta en el lado inferior de su asiento de seguridad infantil. USA: 1-888-224-6549 o www.gracobaby.
2.0 Características y componentes Cada modelo del asiento de seguridad infantil viene con varias opciones de correas. Para ajustar su asiento de seguridad infantil correctamente, es muy importante que siga las instrucciones apropiadas para el modelo que haya comprado.
2.
VISTA TRASERA: CORREAS DE 3 PUNTOS Capota Ajuste de correas Mango para soltar Indicador de nivel* Hebilla de las correas Ranura para las correas Agujero de montaje Seguro para la unión Bolsillo para el manual del propietario *Indicador de nivel **Clip de cierre Clip de cierre** El indicador de nivel se encuentra en el lado del asiento de seguridad infantil e indica si el asiento de seguridad infantil está reclinado correctamente.
2.
VISTA TRASERA: CORREAS DE 5 PUNTOS Capota Mango para soltar Agujero de montaje Indicador de nivel* Ranura para las correas Bolsillo para el manual del propietario Seguro para la unión Hebilla de la correa de la cintura Placa de unión metálica Correa de ajuste Clip de cierre** *Indicador de nivel **Clip de cierre El indicador de nivel se encuentra en el lado del asiento de seguridad infantil e indica si el asiento de seguridad infantil está reclinado correctamente.
2.3 Quitar y sujetar la base Para quitar el asiento de seguridad infantil, apriete el mango detrás del asiento y levante el asiento de seguridad infantil de la base como se muestra . Para colocar el asiento de seguridad infantil en la base, empuje el asiento hacia abajo hasta que se enganche en la base. Jale el asiento de seguridad infantil hacia arriba para asegurarse de que esté bien sujeto en la base. 2.4 Ajustar el asa 1. Apriete los botones de ajuste del asa en ambos lados del asa . 2.
2.5 Sujetar la capota 1. El asiento de seguridad infantil viene con cuatro (dos en ciertos modelos) piezas de soporte idénticas para la capota Pase un soporte de capota completamente por una de las costuras . 2. Deslice el extremo recto del segundo soporte en el extremo recto del primer soporte . 3. En los modelos con cuatro soportes de capota, repita los pasos uno y dos para la otra costura de la capota. La capota debe aparecer como se muestra . 4.
2.6 Soporte de la cabeza (en ciertos modelos) Algunos niños pueden necesitar soporte adicional para mantener su cabeza y cuerpo en una posición cómoda. Desabroche los lados y vuelva a abrocharlos en las correas pasándolas por las ranuras en la almohadilla . Si su modelo no cuenta con un soporte para la cabeza, quizá desee usar una toalla o cobija enrollada para soporte . ASEGÚRESE DE QUE NADA INTERFIERA CON LAS CORREAS. Deben estar planas y ajustadas en los hombros de su niño. 2.
3.0 Información importante 3.1 Advertencias para su uso como asiento de seguridad infantil • NO INSTALE NI USE ESTE ASIENTO DE SEGURIDAD INFANTIL NI SU BASE HASTA QUE HAYA LEIDO Y ENTENDIDO LAS INSTRUCCIONES EN ESTE MANUAL Y EN EL MANUAL DEL PROPIETARIO DE SU VEHÍCULO. NO deje a otros instalar o usar el asiento de seguridad infantil a menos que sepan usarlo. • EL USO INCORRECTO DE ESTE ASIENTO DE SEGURIDAD INFANTIL Y BASE AUMENTA EL RIESGO DE LESIONES GRAVES O LA MUERTE EN PARADAS REPENTINAS O ACCIDENTES.
• ALGUNOS NIÑOS CON NECESIDADES ESPECIALES, tales como bebés prematuros o aquellos que han sido diagnosticados con apnea posicional, pueden correr un riesgo aumentado de sufrir trastornos respiratorios y otros trastornos en un asiento de seguridad infantil. Si su niño tiene necesidades especiales, recomendamos que pida a su médico o al personal del hospital una evaluación de su niño y que le recomienden el asiento o cama de seguridad infantil apropiado antes de usar este producto.
• NO MODIFIQUE SU ASIENTO DE SEGURIDAD INFANTIL Y BASE ni use cualquier accesorio o pieza proporcionados por otros fabricantes. • NUNCA USE EL ASIENTO DE SEGURIDAD INFANTIL Y LA BASE SI TIENE PIEZAS DAÑADAS O FALTANTES. No use una correa del asiento de seguridad infantil ni un cinturón de seguridad del vehículo si está cortado, deshilachado o dañado. • EL ASIENTO DE SEGURIDAD INFANTIL PUEDE CALENTARSE MUCHO SI SE DEJA AL SOL.
3.3 Advertencias adicionales para su uso como portabebés • PELIGRO DE CAÍDA: Los movimientos del niño pueden hacer que el portabebés se deslice. NUNCA coloque el portabebés cerca de los bordes de encimeras, mesas u otras superficies altas. Siempre manténgase al alcance de la mano cuando el portabebés no está en el piso/suelo. ASEGÚRESE de que el asa se enganche en su posición cerrada antes de levantar el portabebés. NUNCA coloque el portabebés encima de un carrito de compras.
3.4 Límites de altura y de peso NO USAR ESTE ASIENTO DE SEGURIDAD INFANTIL DE MANERA APROPIADA PARA EL TAMAÑO DE SU NIÑO PUEDE AUMENTAR EL RIESGO DE LESIONES GRAVES O LA MUERTE. Su niño DEBE cumplir con todos los requisitos: • PESO: 20 libras (9 kg) o menos • ALTURA: 26 pulgadas (66 cm) o menos 4.0 Ubicación del asiento de seguridad infantil 4.1 Requisitos para el asiento del auto LA COLOCACIÓN INCORRECTA DEL ASIENTO DE SEGURIDAD INFANTIL AUMENTA EL RIESGO DE LESIONES GRAVES O LA MUERTE.
• Cuando sea posible, sujete el asiento de seguridad infantil en la posición central del asiento directamente detrás de los asientos delanteros . Un adulto debe ir en el asiento trasero para controlar al niño. Si el conductor es el único adulto presente, un niño podrá necesitar ir en el asiento delantero, PERO SOLAMENTE si no hay una bolsa de aire en el lado del pasajero y se cumplan todos los demás requisitos para el asiento y los cinturones de seguridad del vehículo.
• NO USE EL ASIENTO DE SEGURIDAD INFANTIL EN ASIENTOS DEL VEHÍCULO CON RESPALDOS QUE NO SE CIERREN EN LA POSICIÓN VERTICAL. NO use asientos que se doblan sin contar con un cierre de algún tipo para soltarlos. Estos asientos pueden lanzarse hacia delante y golpear al niño en una parada repentina o un accidente. 4.2 Requisitos para los cinturones de seguridad del auto MUCHOS SISTEMAS DE CINTURONES DE SEGURIDAD NO SON SEGUROS PARA USAR CON EL ASIENTO DE SEGURIDAD INFANTIL.
4.2.1 Sistemas de cinturones de autos INSEGUROS NO use ninguno de los siguientes sistemas para sujetar el asiento de seguridad infantil. • Cinturones de regazo con retractor de cierre en caso de emergencia (ELR) Este cinturón de seguridad se mantiene suelto y puede moverse hasta que se cierra en un accidente o una parada repentina • Cinturones combinados de regazo/hombro con retractor Cada correa tiene un retractor en un extremo y se junta a la placa de unión en el otro extremo.
4.2.2 Sistemas de cinturones de autos SEGUROS LOS SIGUIENTES SISTEMAS DE CINTURONES SE PUEDEN USAR CON SU ASIENTO DE SEGURIDAD INFANTIL, SI la ubicación del asiento cumple con todos los demás requisitos de estas instrucciones y las del manual del propietario de su vehículo. • Cinturones de regazo ajustados manualmente Cuando se abroche, el cinturón se ajusta manualmente jalando el extremo del cinturón y empujando fuerte hacia abajo en el asiento de seguridad infantil.
• Cinturones combinados de regazo/hombro con placa de cierre deslizable Este cinturón cuenta con una placa de cierre que se desliza libremente a lo largo del cinturón. Este cinturón DEBE convertirse para prevenir el movimiento de la parte del regazo del cinturón. Debe usar el clip de cierre proporcionado con el asiento de seguridad infantil, a menos que el Clip de cierre cinturón de seguridad de su vehículo se pueda convertir de otra forma, según el manual del propietario de su vehículo.
5.0 Usar el asiento de seguridad infantil 5.1 Posición de las correas NO AJUSTAR LAS CORREAS DE MANERA APROPIADA EN SU NIÑO AUMENTA EL RIESGO DE LESIONES GRAVES O LA MUERTE EN EL CASO DE UN GIRO BRUSCO, UNA PARADA REPENTINA O UN ACCIDENTE. Las correas deben ajustarse correctamente en su niño según las instrucciones siguientes. 1. Quite el asiento de seguridad infantil de la base y gire el asa hacia abajo hasta la posición de sentarse. Vea "2.3 Quitar y sujetar la base" y "2.4 Ajustar el asa" en la pág. 11.
5.1.1 Correas de 3 puntos 1. Desde la parte trasera, empuje la hebilla de las correas por la ranura de las correas. Si es necesario, desde la parte delantera, use la correa para jalar Ajuste de la hebilla desde la ranura . correas Hebilla de correas 2. Vuelva a insertar la hebilla de las correas en la ranura apropiada . 3. Desde la parte trasera, quite la correa del ajuste de correas. Si es necesario, desde la parte delantera, use la correa para jalar la hebilla desde la ranura. 4.
5.1.2 Correas de 5 puntos 1. Oprima el botón para ajustar las correas debajo de la funda del asiento . Jale las correas de los hombros para soltarlas. 2. Detrás del asiento, quite los extremos de las dos correas de los hombros de la placa de unión metálica . 3. Desde la parte delantera, jale las correas por las ranuras y vuelva a pasarlas por las ranuras apropiadas. 4. Detrás del asiento, empuje ambas correas de los hombros DEBAJO del bolsillo del manual del propietario hasta que sobresalgan por el fondo.
PARA UN BEBÉ MÁS PEQUEÑO: Use las ranuras de las correas inferiores (si quedan al nivel o justo debajo de los hombros de su niño) y los bucles de las correas superiores . Los extremos de las correas deben colgarse delante de la placa metálica como se muestra en el , no como se muestra en el . VERIFIQUE que los bucles queden completamente dentro de las ranuras de la placa de unión . VERIFIQUE que las correas estén sujetas jalándolas.
5.2 Sujetar al niño en el asiento de seguridad infantil No sujetar a su niño correctamente en el asiento de seguridad infantil/portabebés aumenta en riesgo de graves lesiones o la muerte debido a la asfixia o caídas o en el caso de una parada repentina o un accidente. Incluso cuando se usa exclusivamente como portabebés, asegúrese de que las correas estén sujetas correctamente. 1. Mueva el asiento de seguridad infantil hasta la posición de sentarse (vea la página 11). 2.
5.2.1 Correas de 3 puntos 5. Abroche la correa en el cierre entre las piernas del niño. Asegúrese de que oiga un "clic". NO use el asiento de seguridad infantil si la correa no se cierra en su sitio. Llame a Graco al 1-888-224-6549. 6. Desde la parte trasera, jale la correa por el ajuste de las correas para ajustar las correas como se muestra . VERIFIQUE que ambas correas queden planas y ajustadas en los hombros del niño. 7. Junte las piezas del clip de correas .
5.2.2 Correas de 5 puntos 5. Inserte las dos lengüetas de la hebilla en la hebillas de las correas en la correa de la entrepierna. Asegúrese de que oiga el "clic" de cada lengüeta en la hebilla. NO use el asiento de seguridad infantil si la correa no se cierra en su sitio. Llame a Graco al 1-888-224-6549. 6. Junte las piezas del clip de correas . 7. Jale la correa de ajuste para ajustar las correas como se muestra . VERIFIQUE que ambas correas queden planas y ajustadas en los hombros. 8.
5.3 Instalar el asiento de seguridad infantil y la base Debe seguir cuidadosamente las instrucciones proporcionadas por el fabricante de su vehículo, además de la información en este manual. Asegúrese de que haya leído y entendido las sección 4, "Ubicación del asiento de seguridad infantil" en las páginas 18 a 23.
3. Pase el cinturón de seguridad: La base y asiento de seguridad infantil El cinturón DEBE ir debajo de la lengüeta Asiento de seguridad infantil solamente 4. Abroche el cinturón de seguridad. Asegúrese de que la lengüeta de la hebilla se coloca en la hebilla correcta . El cinturón de seguridad no debe estar doblado ni torcido. 5. Ajuste el cinturón de seguridad del vehículo. Refiérase al manual del propietario de su vehículo y las instrucciones en "4.2.
Para una instalación bien ajustada, empuje hacia abajo fuerte con su rodilla o con una mano libre en el centro del asiento de seguridad infantil o su base y jale y ajuste el cinturón del vehículo. 6. Empuje el asiento de seguridad infantil hacia abajo en la base y asegúrese de que oiga un "clic" . Jale el asiento de seguridad infantil hacia arriba para asegurarse de que está bien sujeto en la base.
5.4 Reclinar el asiento de seguridad infantil y la base Para la seguridad de su niño, es importante que su asiento de seguridad infantil / base se recline correctamente. Adjunto al lado de su asiento de seguridad infantil se encuentra un indicador de nivel para ayudar a reclinar el asiento de seguridad infantil/base correctamente en el asiento del vehículo. No reclinar el asiento de seguridad infantil correctamente en el asiento del vehículo aumenta el riesgo de lesiones graves o la muerte.
Al usar la base: Para bajar el pie; jale del fondo del pie hasta el nivel deseado para ajustar el reclinado . Para levantar el pie; coloque la base en una superficie plana, empuje hacia dentro en las lengüetas de la base para ajustar el reclinado . Si todavía queda color naranja en el in dicador de nivel cuando el pie está completamente extendido, coloque una toalla enrollada debajo del pie hasta que se vea el color azul SOLAMENTE .
Control de seguridad final: Cada vez que maneje con su niño, EMPUJE HACIA ABAJO la parte superior del asiento de seguridad infantil despacio pero firmemente con el fin de asegurar que el cinturón del vehículo no se alargue y que el cinturón del vehículo esté bien abrochado alrededor del asiento de seguridad infantil/base .
6.0 Información adicional 6.1 Uso en aviones Instálelo en un avión de la misma manera que en un automóvil. Notifique a la compañía aérea por adelantado que va a usar el asiento abordo. Úselo solamente en un asiento del aeronave orientado hacia delante. Siga las instrucciones del personal de vuelo sobre la colocación del asiento de seguridad infantil. No use este asiento de seguridad infantil si el cinturón de seguridad del avión no sujeta el asiento de seguridad infantil firmemente. 6.
Con cuidado, quite la almohadilla del asiento. Lávela a máquina en el ciclo delicado y déjela secar al aire. NO USE CLORO. Siga los pasos en sentido inverso para volver a instalar la almohadilla. Verifique que el sistema de correas no esté doblado y jale el sistema de correas para asegurar que las correas están bien reinstaladas. LAS PIEZAS METÁLICAS Y DE PLÁSTICO DEL ASIENTO DE SEGURIDAD INFANTIL se pueden limpiar con una solución de agua y jabón suave. NO USE CLORO.
Notas: 39
Cómo efectuar los pedidos: Complete el formulario a continuación. Los números de modelo y serie del asiento de seguridad infantil DEBEN incluirse en el formulario para asegurar los repuestos apropiados. Su número de modelo se puede encontrar en una etiqueta debajo de su asiento de seguridad infantil. El pago debe acompañar al pedido. Las piezas también se pueden pedir del sitio Web de Graco en www.gracobaby.com. Lista de piezas: Precio:** Almohadilla del asiento ............ $20.00 Capota ..............
Model No. • N° de modelo Serial No.