SnugRide® Classic Connect™ 35 ©2013 Graco PD261464A 11/13 US
1.0 Warning to Parents and Other Users .........................................4-5 2.0 Registration Information ..............................................................6-7 2.1 Register Your Infant Restraint ...................................................6 2.2 For Recall Information ...............................................................6 2.3 If You Need Help .......................................................................7 2.4 Child Restraint Useful Life ...........................
6.0 Choosing an Appropriate Vehicle Seat Location ..................26-32 6.1 Vehicle Seat Requirements ................................................26-27 6.2 Vehicle Seat Belt Requirements ..............................................27 6.2.1 UNSAFE Vehicle Belt Systems ......................................28 6.2.2 SAFE Vehicle Belt Systems ......................................29-31 6.3 LATCH Locations ....................................................................32 7.
1.0 Warnings to Parents and Other Users DO NOT PLACE THIS INFANT RESTRAINT IN A VEHICLE SEATING LOCATION THAT HAS A FRONT AIR BAG. If the air bag inflates, it can hit the infant restraint with great force and cause serious injury or death to your child. Check vehicle owner’s manual for information about side air bags and infant restraint installation. No infant restraint can guarantee protection from injury in every situation.
Failure to properly use this infant restraint increases the risk of serious injury or death in a sharp turn, sudden stop or crash. Your child’s safety depends on you installing and using this infant restraint correctly. Even if using this infant restraint seems easy to figure out on your own, it is very important to READ, UNDERSTAND AND FOLLOW THE OWNER’S MANUAL. The manual is located in a pocket on the back of the infant restraint. You must also read your vehicle owner’s manual.
Model Number: Date of Manufacture: Purchase Date: 2.0 Registration Information 2.1 Register Your Infant Restraint Please fill in the above information. The model number and date of manufacture can be found on a label on the bottom of your infant restraint. Fill out the prepaid registration postcard attached to the seat cover and mail it today. Child restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall.
2.3 If You Need Help In the U.S.A, please contact our Customer Service Department with any questions you may have concerning parts, use, or maintenance. When you contact us, please have your product’s model number and date of manufacture ready so that we may help you efficiently. These numbers can be found on a sticker on the underside of your infant restraint. 1-800-345-4109 or www.gracobaby.com www.cpsc.gov www.NHTSA.gov www.seatcheck.org 2.
3.1 Warnings for Use as an Infant Restraint 3.0 Important Information DO NOT INSTALL OR USE THIS INFANT RESTRAINT AND BASE UNTIL YOU READ AND UNDERSTAND THE INSTRUCTIONS IN THIS MANUAL AND IN YOUR VEHICLE OWNER’S MANUAL. DO NOT let others install or use the infant restraint unless they understand how to use it. FAILURE TO PROPERLY USE THIS INFANT RESTRAINT AND BASE INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN A SUDDEN STOP OR CRASH.
According to accident statistics, CHILDREN ARE SAFER WHEN PROPERLY RESTRAINED IN REAR VEHICLE SEATING POSITIONS, RATHER THAN FRONT SEATING POSITIONS. For a vehicle with a front passenger air bag, refer to your vehicle owner’s manual as well as these instructions for infant restraint installation. NEVER LEAVE YOUR CHILD UNATTENDED. NEVER LEAVE AN INFANT RESTRAINT AND BASE UNSECURED IN YOUR VEHICLE.
NEVER give this infant restraint and base to someone else without also giving them this manual. NEVER use a second-hand infant restraint and base or an infant restraint whose history you do not know. 3.2 Warning for Use With a Stroller USE ONLY WITH STROLLERS THAT ARE PART OF THE GRACO CLASSIC CONNECT™ TRAVEL SYSTEM. Refer to stroller instruction sheet for details about how to attach the infant restraint to your stroller.
3.3 Additional Warnings for Use as a Carrier FALL HAZARD: Child’s movements can slide carrier. NEVER place carrier near edges of countertops, tables or other high surfaces. Always stay within arms reach whenever carrier is not on floor/ground. BE SURE handle locks into position before lifting carrier. NEVER place carrier on the top of a shopping cart. SUFFOCATION HAZARD: Infant carrier can roll over on soft surfaces and suffocate child. Never place carrier on beds, sofas or other soft surfaces.
3.4 Height and Weight Limits TO AVOID SERIOUS INJURY OR DEATH DO NOT USE THE INFANT RESTRAINT WITH A CHILD LARGER OR SMALLER THAN THE WEIGHT AND HEIGHT RANGE LISTED BELOW. Your child MUST meet the following requirements: WEIGHT: 4-5 lbs. (1.8-2.3 kg) WITH full 2-part body support assembly 5-35 lbs. (2.3-15.87 kg) AND HEIGHT: 32 inches (81 cm) or less in height. IMPORTANT: MAKE SURE the top of the childs' head is at least 1" (2.54 cm) below the top of the infant restraint. 12 1" (2.
FRONT VIEW Handle Harness slots Chest Clip Waist slots Harness Strap Vehicle belt hook Harness buckle tongues Harness adjustment strap Harness buckle Harness adjustment button 13 4.
REAR VIEW Release handle Canopy Harness slot Level indicator* Owner’s manual pocket Anchor Clip Harness storage for a smaller child Metal junction plate Harness adjustment strap Locking clip storage** *Level Indicator The level indicator is attached to the side of the infant restraint and indicates whether or not the infant restraint is properly reclined. **Locking Clip The locking clip is stored on the bottom of the infant restraint.
BASE Lock-off Vehicle belt/LATCH* path Knob for Adjustable Foot Adjustable Foot LATCH Storage Bars (underneath) LATCH Adjustment Belt LATCH Connector United States Federal Motor Vehicle Safety Standards have defined a system for installing car seats in vehicles. The system is called LATCH. * LATCH may be used IN PLACE of vehicle belt ONLY if vehicle is equipped with LATCH anchor points. Please refer to vehicle owner’s manual for LATCH locations.
4.1 Adjusting Handle 1. Press handle adjustment buttons on both sides of handle . 2. Rotate handle until it clicks into any of the 4 positions: Position A: MUST be used when carrying by handle, Position A,B,C,D: may be used in vehicle BOTH handle adjustment buttons must pop out to lock handle in place . 3. Push and pull on the handle to be sure it is locked firmly in position. Carrying A B C D Sitting 4.
4.3 Attaching Canopy 1. Infant restraint comes with four identical canopy support parts. Thread one canopy support completely through sewn channel . 2. Slide straight end of a second support into the straight end of the first support and snap in place . 3. Repeat steps one and two for the other canopy tunnel. The canopy should appear as shown . 4. Attach canopy in the areas between the infant restraint and the base of the handle .
4.4 2-Part Body Support To prevent ejection in sudden stop or crash: shoulder straps must be threaded through slots and properly positioned on shoulders. Only use top body support in bottom 2 sets of harness slots. Attach hook and loop on bottom support to back of top support . Infants 4-5 lbs. (1.8-2.3 kg) MUST use fully assembled 2 part body support . Infants over 5 lbs. (2.3 kg) MAY use fully assembled if their shoulders are still under the bottom harness slots.
4.5 Cold Weather Boot (on certain models, styles vary) Some models come with a cold weather boot. To use, wrap elastic around bottom of seat and attach both elastic loops around vehicle belt hooks as shown . 4.6 Harness Covers (on certain models, styles vary) To prevent ejection in sudden stop or crash: Always make sure shoulder straps are threaded through slots and properly positioned on shoulders. Make sure that harness covers do not interfere with placement of the chest clip at armpit level.
5.0 Using Infant Restraint 5.1 Positioning Harness Straps FAILURE TO PROPERLY ADJUST THE HARNESS STRAPS FOR YOUR CHILD INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN THE EVENT OF A SHARP TURN, SUDDEN STOP OR CRASH. The harness straps must be properly adjusted to fit your child according to the following instructions. 1. Remove infant restraint from base and rotate handle down to sitting position. See “4.1 Adjusting Handle” and “4.2 Removing and Attaching Infant Restraint”, page. 16. 2.
A. Push the harness adjustment button under the seat flap. Pull the shoulder straps out to loosen the harness . B. From behind seat, pull the metal junction plate down behind the owner’s manual pocket and remove the ends of the two shoulder straps from the metal junction plate . C. From front, pull straps through the Harness adjustment harness slots and then reinsert them button through the appropriate slots. Both harness straps must be through the same set of slots in the seat and pad. D.
Shoulder Straps for a SMALLER Baby: For infants 4-5 lbs. (1.8-2.3 kg) you must use the 2 part body support, see page 18. Use the lower harness slots (if they are even with or just below your child’s shoulders) and the upper strap loops . The ends of the straps must hang in front of the metal junction plate as shown in , not as shown in . m baby.co graco CHECK that the loops are completely within junction plate slots . CHECK that straps are secure by pulling on them.
To Shorten Waist Straps for a SMALLER Baby: For infants 4-5 lbs. (1.8-2.3 kg) you must use the 2 part body support, see page 18. The length of the waist strap can be shortened further by pushing aside the small tab that holds the anchor clips in place and pull the anchor clips out of their indentations . Move the anchor clip to the second loop in the strap . CHECK that anchor clips are threaded properly. The ends of the straps must be inserted under the storage tabs as shown in ¡.
5.2 Securing Child in Infant Restraint Failure to properly secure your child in the infant restraint/carrier increases the risk of serious injury or death from suffocation or falls, or in the event of a sudden stop or crash. Even when used only as a carrier, make sure the harness straps are properly secured. 1. Move infant restraint handle to sitting position (see page 16). 2. Open chest clip by squeezing both sides and unbuckle as shown . 3.
5. Snap chest clip pieces together . 6. Pull on harness adjustment strap to tighten straps as shown . CHECK that both straps are flat and snug on shoulders and thighs. .com aby cob gra 7. Position chest clip in middle of chest, level with armpits and away from the neck . 8. SAFETY CHECK: a) CHECK that harness straps are not twisted. b) CHECK that the harness is snug. You should not be able to pinch the harness if it is snug. A snug strap should not allow any slack.
6.0 Choosing an Appropriate Vehicle Seat Location 6.1 Vehicle Seat Requirements IMPROPER PLACEMENT OF THE INFANT RESTRAINT INCREASES THE RISK OF SERIOUS INJURY OR DEATH. Some seating positions in your vehicle may not be safe for this infant restraint. Some vehicles do not have any seating positions that can be used safely with the infant restraint. If you are not sure where to place the infant restraint in your vehicle, consult your vehicle owner’s manual or call Graco at 1-800-345-4109.
The VEHICLE seat must face forward. DO NOT use infant restraint on vehicle seats with seat backs that will not lock in an upright position. DO NOT use seats that can fold down without having to release a lock or latch of some kind. These seats can fly forward and strike the child in a sudden stop or crash. 6.2 Vehicle Seat Belt Requirements MANY SEAT BELT SYSTEMS ARE NOT SAFE TO USE WITH THE INFANT RESTRAINT. THE VEHICLE SEAT BELT MUST BE DESIGNED TO HOLD THE INFANT RESTRAINT TIGHTLY AT ALL TIMES.
6.2.1 UNSAFE Vehicle Belt Systems LATCH can be used IN PLACE OF the vehicle belt system. Please refer to vehicle owner’s manual for LATCH locations. DO NOT use any of the following systems to secure the infant restraint. Lap Belts with Emergency Locking Retractor (ELR) This lap belt stays loose and can move until it locks in a crash or sudden stop. Combination Lap/Shoulder Belt with Retractor Each strap has a retractor at one end and is attached to the latch plate at the other end.
6.2.2 SAFE Vehicle Belt Systems THE FOLLOWING BELT SYSTEMS CAN BE USED WITH YOUR INFANT RESTRAINT, IF the seat location meets all other requirements of these instructions and those in your vehicle owner’s manual. LATCH can be used in place of the vehicle belt system. Please refer to vehicle owner’s manual for LATCH locations. When using infant restraint without the base, adjust the belt as described in this section for these types of vehicle seat belts.
Lap Belts with Automatic Locking Retractor (ALR) The automatic locking retractor will not permit the lap belt to lengthen once it is buckled. Tighten the belt by feeding the belt back into the retractor while pushing down hard on the infant restraint. Combination Lap/Shoulder Belt with Locking Latch Plate Once it is buckled, this type of belt has a latch plate that will not allow the lap portion of the belt to loosen.
Combination Lap/Shoulder This belt has a latch plate that slides freely along the belt. Belt with Sliding Latch Plate This belt MUST be converted to prevent movement of the lap portion of the belt. You must use a locking clip (provided with the infant restraint) when using the infant restraint without the base unless your vehicle’s seat belt can be Locking clip converted in another way as described in your vehicle owner’s manual. 1 To Install Locking Clip: (DO NOT use with base) /2 inch (1 cm) 1.
6.3 LATCH Locations Newer vehicles may have one or more seating positions with LATCH anchorage systems. If vehicle is equipped with LATCH, the vehicle lower anchor points may be visible at the vehicle seat crease. If not visible, they may be marked with the symbol . See your vehicle owner’s manual for exact locations, anchor identification, and requirements for use with an infant restraint.
You must carefully follow the instructions provided by your vehicle manufacturer, in addition to the information in this manual. Before proceeding be sure you have read and understood section 6, “Choosing an Appropriate Vehicle Seat Location” on pages 26-32. Make sure vehicle is on level ground so that the level indicator, which is attached to the infant restraint, can be used to properly recline the infant restraint.
3. Buckle the vehicle belt. Make sure the buckle tongue goes into the correct buckle . The seat belt should not be twisted or turned. 4. Tighten the vehicle seat belt. Refer to your vehicle owner’s manual and the instructions in “6.2.2 SAFE Vehicle Belt Systems”, page 29-31, on tightening your vehicle belt when using the infant restraint without base. To create a secure installation, push down hard with your free hand on the infant restraint and pull and tighten the vehicle belt. 5.
7.2 Installing the Infant Restraint Without Base Using Vehicle Belt (Alternate Method) You must carefully follow the instructions provided by your vehicle manufacturer, in addition to the information in this manual. Before proceeding be sure you have read and understood section 6, “Choosing an Appropriate Vehicle Seat Location” on pages 26-32. Make sure vehicle is on level ground so that the level indicator, which is attached to the infant restraint, can be used to properly recline the infant restraint.
4. Buckle the vehicle belt. Make sure the buckle tongue goes into the correct buckle . The seat belt should not be twisted or turned. 5. Tighten the vehicle seat belt. Refer to your vehicle owner’s manual and the instructions in “6.2.2 SAFE Vehicle Belt Systems”, page 29-31, on tightening your vehicle belt when using the infant restraint without base. To create a secure installation, push down hard with your free hand in the infant restraint and pull and tighten the vehicle belt. 6.
Lap Belt Lap/Shoulder Belt Belts MUST go under lock-off 3. To create a secure installation, while pushing down on the base, pull the free end of the lap belt or the shoulder portion of the lap/shoulder belt to tighten . 4. Close lock-off over lap belt AND free end or the lap/shoulder belts . Make sure that you push the top of the lock-off all the way down. 5. Check that belt does not move by pulling and pushing hard on base. If belt loosens or lengthens, repeat procedure.
6. Push the infant restraint down into the base and make sure that you hear a “click” . Pull up on the infant restraint to be sure it is latched securely into the base. If the infant restraint does not securely latch into the base, the infant restraint provides NO protection for your child. DO NOT use the infant restraint/base if the infant restraint does not securely latch into the base. 7. Test infant restraint for secure installation as described in infant restraint “Final Safety Check” page 42.
7.4 Using LATCH to install Base 1. For ease of installation, extend LATCH to its maximum length and remove from storage bars. 2. Position base in vehicle seat as shown. 3. Make sure LATCH is through vehicle/LATCH belt path normally used for vehicle seat belt. . Belt must lay flat and not be twisted. 4. Hook Connectors to vehicle lower anchors. Pull firmly on Connectors to be sure they are attached . 5. Tighten LATCH by pushing down hard on base and pulling the adjustment belt . 6.
7.5 Reclining Infant Restraint/Base For your child’s safety, it is important that your infant restraint/base be properly reclined. Attached to the side of your infant restraint is a level indicator to help properly recline the infant restraint/base on the vehicle seat. Failure to properly recline the infant restraint on the vehicle seat increases the risk of serious injury or death. If the infant restraint is too upright, a child’s head may drop forward and cause breathing problems.
To Adjust Recline on Base: Turn the knob clockwise to the desired setting to lower the foot . Turn the knob counter clockwise to raise the foot . If there is still orange in the level indicator when the foot is completely extended then raise the foot and place a rolled towel under the foot until ONLY blue shows.
Final Safety Check: Every time you drive with your child, PUSH DOWN on the top of the infant restraint slowly but firmly to make sure the vehicle belt does not lengthen at all and that the vehicle belt or LATCH is fastened securely around the infant restraint/base . Holding the infant restraint or base near the vehicle belt path, TWIST AND PULL the infant restraint forward and to both sides to make sure the vehicle belt or LATCH does not lengthen or loosen and the infant restraint does not easily move.
When installing in an airplane using the base, install the same way as in an automobile with a lap only belt leaving the lock off fully opened to allow for buckle clearance. If using the shell only installing follow the same instructions as an automobile. Notify the airline ahead of time that you intend to bring the seat on board. Use only in forward-facing aircraft seat. Follow the flight attendants instructions about infant restraint placement.
8.3 Cleaning and Maintenance TO REMOVE AND WASH INFANT RESTRAINT PAD, follow instructions in “5.1 Positioning Harness Straps”, pages 20-23 to remove the harness straps from the metal junction plate. Push aside the small tab that holds the anchor clips in place and pull the anchor clips out of their indentations. Remove the anchor clips from the harness straps and push straps through seat slots .
INFANT RESTRAINT METAL AND PLASTIC PARTS may be cleaned by wiping with a mild soap and water solution. DO NOT USE BLEACH OR DETERGENT which may weaken plastic parts. HARNESS STRAPS may be spot cleaned or replaced. DO NOT IMMERSE THE HARNESS STRAPS IN WATER. Doing so may weaken the harness straps. NEVER iron the harness straps. IF HARNESS STRAPS have cuts, fraying or become badly twisted, you must replace the straps. DO NOT USE INFANT RESTRAINT without seat pad.
8.3.1 Buckle Cleaning Process PREVENT SERIOUS INJURY OR DEATH: Buckle must be properly latched. Periodically inspect and clean buckle to remove objects or debris that could prevent latching. 1. Turn restraint over, push retainer through crotch strap slot . 2. To clean buckle - place in a cup of warm water and gently agitate the buckle, press the red button several times while in the water . DO NOT SUBMERGE THE HARNESS WEBBING. DO NOT USE SOAPS or LUBRICANTS. DO NOT use household detergents.
Notes
Replacement Parts To purchase parts or accessories or for warranty information in the United States, please contact us at the following: www.gracobaby.
SnugRide® Classic Connect™ 35 ©2013 Graco PD261464A 11/13 US
1.0 Advertencias a padres y otros dueños ......................................4-5 2.0 Información sobre el registro......................................................6-7 2.1 Registro de su sistema de seguridad para bebés .....................6 2.2 Información sobre el retiro de productos del mercado ..............7 2.3 Si necesita ayuda ......................................................................7 2.4 Vida útil del sistema de seguridad para niños ...........................7 3.
6.0 Cómo elegir un lugar apropiado para el asiento del vehículo ...............................................................................26-32 6.1 Requisitos del asiento del vehículo ....................................26-27 6.2 Requisitos del cinturón de seguridad del vehículo ..................27 6.2.1 Sistemas PELIGROSOS de cinturones de vehículos ....28 6.2.2 Sistemas SEGUROS de cinturones de vehículos.....29-31 6.3 Ubicación del LATCH ..............................................................
1.0 Advertencias a padres y otros dueños NO PONGA ESTE SISTEMA DE SEGURIDAD PARA BEBÉS EN UN ASIENTO DEL VEHÍCULO EQUIPADO CON UNA BOLSA DE AIRE DELANTERA. Si la bolsa de aire se infla, puede golpear al sistema de seguridad para bebés con mucha fuerza y causar lesiones serias o la muerte de su niño. Consulte el manual del dueño del vehículo para obtener información sobre las bolsas de aire laterales y la instalación del sistema de seguridad para bebés.
A pesar de que el uso de este sistema de seguridad para bebés parezca fácil de descifrar, es muy importante LEER, ENTENDER Y SEGUIR EL MANUAL DEL DUEÑO. El manual se encuentra en el bolsillo trasero del sistema de seguridad para bebés. También debe leer el manual del dueño de su vehículo. La seguridad de su niño depende de: 1. Elegir un lugar apropiado en su vehículo.
Número de modelo: Fecha de fabricación: Fecha de compra: 2.0 Información sobre el registro 2.1 Registro de su sistema de seguridad para bebés Por favor, complete la información que se solicita más arriba. El número de modelo y la fecha de fabricación se pueden encontrar en una etiqueta en el fondo de su sistema de seguridad para bebés. Llene la tarjeta postal de registro prepagada que se encuentra en la funda del asiento y envíela hoy mismo.
2.3 Si necesita ayuda En los EE.UU. por favor, comuníquese con nuestro Departamento de Servicio al Cliente con cualquier pregunta que pudiera tener sobre piezas, uso o mantenimiento. Cuando se ponga en contacto con nosotros, por favor tenga listo el número de modelo y la fecha de fabricación para que lo podamos ayudar más eficientemente. Estos números pueden encontrarse en una etiqueta ubicada en la parte inferior de su sistema de seguridad para bebés. 1-800-345-4109 o www.gracobaby.com www.cpsc.gov www.
3.0 Información importante 3.1 Advertencias para uso como sistema de seguridad para bebés NO INSTALE O USE ESTE SISTEMA DE SEGURIDAD PARA BEBÉS Y BASE HASTA QUE HAYA LEÍDO Y ENTENDIDO LAS INSTRUCCIONES EN ESTE MANUAL Y EN EL MANUAL DEL DUEÑO DE SU VEHÍCULO. NO deje que otros instalen o usen el sistema de seguridad para bebés a menos que entiendan cómo usarlo.
ALGUNOS NIÑOS CON NECESIDADES ESPECIALES, tales como bebés que nacen antes de tiempo o quienes sufren de apnea de posición, podrían sufrir más riesgo de sufrir problemas respiratorios u otras dificultades en un sistema de seguridad para bebés. Si su niño tiene necesidades especiales, recomendamos que su médico o personal del hospital evalúe a su niño y recomiende el sistema de seguridad para bebés adecuado para su bebé o cama para el automóvil adecuado antes de usar este producto.
NUNCA USE EL SISTEMA DE SEGURIDAD PARA BEBÉS Y LA BASE SI HAN RESULTADO DAÑADOS O LE FALTAN PIEZAS. NO use un arnés de sistema de seguridad para bebés o cinturón del asiento del vehículo o cinturón del LATCH rotos, deshilachados o dañados. EL SISTEMA DE SEGURIDAD PARA BEBÉS PUEDE ALCANZAR ALTAS TEMPERATURAS SI LO QUEDA EN EL SOL. Toque siempre la superficie de cualquier pieza de metal o de plástico antes de poner a su niño en el sistema de seguridad para bebés.
3.3 Advertencias adicionales para el uso como transportador PELIGRO DE CAÍDA: Los movimientos del niño pueden mover el transportador. NUNCA ponga el transportador cerca de los bordes de mesadas, mesas u otras superficies altas. Manténgase siempre cerca cuando el transportador no esté en el piso/tierra. Antes de levantar el transportador, ASEGÚRESE que las manijas estén trabajadas en posición. No ponga NUNCA el transportador encima de un carrito de compras.
3.4 Limitaciones de peso y estatura PARA EVITAR LESIONES SERIAS O LA MUERTE NO USE EL SISTEMA DE SEGURIDAD PARA BEBÉS CON UN NIÑO QUE SEA MÁS GRANDE O MÁS PEQUEÑO QUE LA GAMA DE ALTURA Y PESO LISTADA A CONTINUACIÓN. Su niño DEBE cumplir todos los requisitos: PESO: de 4 a 5 libras (1.8-2.3 kg) CON el ensamblaje completo del soporte del cuerpo de 2 partes de 5 a 35 libras (2.3-15.87 kg) Y ALTURA: 32 pulgadas (81 cm) o menos de altura. 1" (2.
VISTA DELANTERA Manija Ranuras para el arnés Presilla para el pecho Ranuras para la cintura Correa del arnés Gancho del cinturón del vehículo Lenguas de la hebilla del arnés Correa de ajuste del arnés Hebilla del arnés Botón de ajuste del arnés 13 4.
VISTA TRASERA Manija de liberación Capota Ranuras para el arnés Indicador del nivel* Bolsillo del manual del dueño Traba de anclaje Almacenamiento del arnés para un niño más pequeño Placa de la unión de metal Correa de ajuste del arnés Almacenamiento de la traba de seguridad** *Indicador del nivel El indicador de nivel se conecta al costado del sistema de seguridad para bebés e indica si el sistema de seguridad para bebés está debidamente inclinado.
BASE Traba del cinturón Paso del LATCH*/cinturón del vehículo Perilla para pie ajustable Pie ajustable Barras de almacenamiento del LATCH (debajo) Cinturón de ajuste del LATCH Conector del LATCH Las Normas Federales para Seguridad de Automóviles de Estados Unidos han determinado un sistema de instalación de asientos de seguridad en los vehículos. El sistema se denomina LATCH. * LATCH debe usarse SOLAMENTE EN LUGAR del cinturón del vehículo si el vehículo está equipado con puntos de anclaje LATCH.
4.1 Ajuste de la manija 1. Apriete los botones de ajuste de la manija en ambos costados de la manija . 2. Gire la manija hasta que se trabe en una de las 4 posiciones: Posición- A: DEBE usarse cuando se transporta de la manija, PosicionesA,B,C,D: pueden usarse en el vehículo. AMBOS botones de ajuste de la manija deben saltar para trabar la manija en su lugar . 3. Empuje y tire de la manija para asegurarse que esté firmemente trabada en su lugar. Transporte A B C D Sentado 4.
4.3 Colocación de la capota 1. El sistema de seguridad para bebés viene con cuatro piezas idénticas de soporte de la capota. Pase un soporte de la capota completamente a través del túnel cosido . 2. Deslice el extremo recto del segundo soporte en el extremo recto del primer soporte . 3. Repita los pasos uno y dos en el otro túnel de la capota. La capota deberá aparecer como se indica . 4. Sujete la capota en los lugares entre el sistema de seguridad para bebés y la base de la manija .
4.4 Soporte del cuerpo de 2 partes Para prevenir la eyección en un accidente o parada repentina, las correas del hombro deben pasar a través de las ranuras y estar debidamente colocadas sobre los hombros. Use el soporte superior del cuerpo solamente en los 2 juegos inferiores de las ranuras del arnés. Sujete la cinta de gancho y nudo desde el soporte inferior hasta la parte trasera del soporte superior .
4.5 Bota para tiempo frío (en ciertos modelos, los estilos varían) Algunos modelos vienen con una bota para tiempo frío. Para usarla, ponga el elástico alrededor del fondo del asiento y coloque los dos nudos elásticos alrededor de los ganchos del cinturón del vehículo como se indica . 4.6 Cubiertas de arnés (ciertos modelos) Para prevenir la eyección en un accidente o parada repentina: Asegúrese siempre que las correas del hombro pasan por las ranuras y están debidamente instaladas en los hombros.
5.0 Uso del sistema de seguridad para bebés 5.1 Colocación de las correas del arnés NO AJUSTAR DEBIDAMENTE LAS CORREAS DEL ARNÉS DEL NIÑO AUMENTA EL RIESGO DE SUFRIR LESIONES SERIAS O LA MUERTE EN CASO DE UNA CURVA CERRADA, PARADA REPENTINA O ACCIDENTE. Las correas del arnés deben estar debidamente ajustadas según el calce de su niño de acuerdo a las siguientes instrucciones. 1. Saque el sistema de seguridad para bebés de la base y gire la manija hacia abajo hasta la posición de sentado.
A. Empuje el botón de ajuste del arnés debajo de la aleta del asiento. Tire las correas de los hombros para aflojar el arnés . B. Detrás del asiento, tire de la placa de unión de metal atrás del bolsillo para el manual del dueño y saque los extremos de las dos correas para los hombros de la placa de unión de metal . C. Desde adelante, pase las correas a través Botón de ajuste de las ranuras del arnés y luego vuelva a del arnés colocarlas a través de las ranuras apropiadas.
Correas para los hombros para un niño PEQUEÑO: Para bebés que pesan de 1,8 a 2,3 kg (4 a 5 libras) debe usar las ranuras inferiores y el soporte del cuerpo de 2 partes, vea la página 18. Use las ranuras inferiores del arnés (si están a la par o apenas debajo de los hombros de su niño) y los nudos superiores de la correa . Los extremos de las correas deben quedar al frente de la placa de unión de metal como se indica en , no como se indica en . m baby.
Cómo acortar las correas para la cintura para un niño PEQUEÑO: Para bebés que pesan de 1,8 a 2,3 kg (4 a 5 libras) debe usar las ranuras inferiores y el soporte del cuerpo de 2 partes, vea la página 18. La longitud de la correa para la cintura puede acortarse más al sacar la pequeña lengüeta que mantiene las hebillas de anclaje en su lugar y sacar las hebillas de anclaje fuera de las hendiduras . Mueva la hebilla de anclaje hasta el segundo nudo de la correa .
5.2 Sujetar el niño en el sistema de seguridad No ajustar debidamente a su niño en el sistema de seguridad para bebés/transportador aumenta el riesgo de lesiones serias o la muerte por asfixia, o caídas o en caso de una parada repentina o accidente. Inclusive cuando lo usa solamente como transportador, asegúrese que las correas del arnés estén debidamente ajustadas. 1. Mueva la manija del sistema de seguridad para bebés a la posición de sentado (vea la página 16). 2.
5. Trabe las piezas de la precilla para el pecho . 6. Tire de la correa de ajuste del arnés para ajustar las correas como se indica . ASEGÚRESE que ambas correas estén planas y ajustadas sobre los hombros y las caderas. .com aby cob gra 7. Coloque la precilla para el pecho en el medio del pecho, a nivel con las axilas y lejos del cuello . 8. VERIFICACIÓN DE SEGURIDAD: a) VERIFIQUE que las correas del arnés no estén dobladas. b) VERIFIQUE que el arnés esté tensionado.
6.0 Cómo elegir un lugar apropiado para el asiento del vehículo 6.1 Requisitos del asiento del vehículo LA COLOCACIÓN INADECUADA DEL SISTEMA DE SEGURIDAD PARA BEBÉS AUMENTA EL RIESGO DE SUFRIR LESIONES SERIAS O LA MUERTE. Algunas posiciones de asiento en su vehículo podrían no ser seguras para este sistema de seguridad para bebés. Algunos vehículos no tienen posiciones de asiento que puedan usarse sin peligro con el sistema de seguridad para bebés.
El asiento del VEHÍCULO debe estar orientado hacia adelante. NO USE el sistema de seguridad para bebés en asientos del vehículo con respaldos que no traben en la posición vertical. NO use asientos que se puedan plegar sin tener que liberar una traba o dispositivo de algún tipo. Estos asientos pueden desplazarse hacia adelante y golpear al niño en un accidente o parada repentina. 6.
6.2.1 Sistemas PELIGROSOS de cinturones de vehículos El LATCH puede usarse EN LUGAR DEL sistema de cinturones del vehículo. Por favor, consulte el manual del dueño del vehículo para identificar las ubicaciones donde debe instalarse el LATCH. NO USE ninguno de los siguientes sistemas para sujetar el sistema de seguridad para bebés.
6.2.2 Sistemas SEGUROS de cinturones de vehículos LOS SIGUIENTES CINTURONES DE SEGURIDAD PUEDEN USARSE CON SU SISTEMA DE SEGURIDAD PARA BEBÉS, SI el asiento cumple con todos los otros requisitos de estas instrucciones y los que se incluyen en su manual del dueño del vehículo. El LATCH puede usarse en lugar del sistema de cinturones del vehículo. Por favor, consulte el manual del dueño del vehículo para identificar las ubicaciones donde debe instalarse el LATCH.
Cinturones de seguridad para la cintura con retractor de seguridad automático (ALR) El retractor de seguridad automático no permitirá que el cinturón de seguridad para la cintura se extienda una vez que está sujetado en la hebilla. Ajuste el cinturón pasando el cinturón por el retractor mientras empuja con fuerza el sistema de seguridad para bebés hacia abajo.
Combinación cinturón para la cintura y el hombro con placa de seguridad con traba móvil Traba de seguridad Este cinturón tiene una placa de seguridad que se mueve libremente a lo largo del cinturón. Este cinturón DEBE convertirse para prevenir el movimiento de la parte de la cintura del cinturón.
6.3 Ubicación del LATCH Los vehículos nuevos tienen uno o varios asientos equipados con sistemas de anclaje LATCH. Si el vehículo viene equipado con el sistema LATCH, se pueden ver los puntos de anclaje inferiores en el pliegue del asiento del vehículo. Si no están visibles, pueden estar marcados con el símbolo . Vea su manual del dueño del vehículo para informarse sobre las ubicaciones exactas, la identificación de los anclajes y los requisitos de uso con un sistema de seguridad para bebés.
Debe seguir detenidamente las instrucciones provistas por el fabricante de su vehículo, además de la información de este manual. Antes de seguir, asegúrese de haber leído y entendido la sección 6, “Cómo elegir un lugar apropiado para el asiento del vehículo” en las páginas 26-32. Asegúrese que el vehículo esté nivelado de modo que el indicador de nivel, conectado al sistema de seguridad para bebés, pueda usarse para reclinar adecuadamente el sistema de seguridad para bebés.
3. Trabe el cinturón del asiento. Asegúrese que la lengua de la hebilla pase por la hebilla correcta . El cinturón del vehículo no deberá estar doblado ni dar vuelta. 4. Ajuste el cinturón de seguridad del vehículo. Consulte su manual del dueño del vehículo y las instrucciones en “6.2.2 Sistemas SEGUROS de cinturones de vehículos”, páginas 29 a 31 sobre cómo tensionar el cinturón del vehículo cuando usa el sistema de seguridad para bebés solo.
7.2 Instalación del sistema de seguridad para bebés/sin la base con el cinturón del vehículo (Método alternativo) Debe seguir detenidamente las instrucciones provistas por el fabricante de su vehículo, además de la información de este manual. Antes de seguir, asegúrese de haber leído y entendido la sección 6, “Cómo elegir un lugar apropiado para el asiento del vehículo” en las páginas 26-32.
4. Trabe el cinturón del asiento. Asegúrese que la lengua de la hebilla pase por la hebilla correcta . El cinturón del vehículo no deberá estar doblado ni dar vuelta. 5. Ajuste el cinturón de seguridad del vehículo. Consulte su manual del dueño del vehículo y las instrucciones en “6.2.2 Sistemas SEGUROS de cinturones de vehículos”, páginas 29 a 31 sobre cómo tensionar el cinturón del vehículo cuando usa el sistema de seguridad para bebés solo.
Cinturón de la cintura Cinturón para la cintura/cinturón para el hombro Los cinturones DEBEN pasar debajo de la traba 3. Para crear una instalación bien ajustada, mientras empuja a la base hacia abajo, tire la punta libre del cinturón para la cintura o la parte del hombro del cinturón para el hombro/cintura para apretarlo . 4. Cierre la traba sobre ambos los cinturones del hombro Y la cintura . Asegúrese que puede empujar la parte de arriba de la traba bien hacia abajo. 5.
6. Empuje el sistema de seguridad para bebés hacia abajo en la base y asegúrese de que escucha un “clic” . Tire hacia arriba del sistema de seguridad para bebés para asegurarse que esté trabado apretadamente en la base. Si el sistema de seguridad para bebés no se traba apretadamente en la base, el sistema de seguridad para bebés NO proporciona ninguna protección a su niño. NO use la base/sistema de seguridad si el sistema de seguridad para bebés no está debidamente trabado en la base. 7.
7.4 Utilización del LATCH para instalar la base 1. Para facilitar la instalación, extienda el LATCH hasta su máxima longitud y sáquelo de las barras de almacenamiento. 2. Ponga la base en el asiento del vehículo como se indica. 3. Pase el LATCH por el recorrido del cinturón/LATCH en la base que normalmente se usa para el cinturón del asiento del vehículo . El cinturón debe mantenerse en posición plana sin doblarse. 4. Enganche los Conectores a los anclajes inferiores del vehículo.
7.5 Inclinación del sistema de seguridad para bebés/base Es importante que su sistema de seguridad para bebés/base esté debidamente inclinado para mayor seguridad de su niño. En el costado de su sistema de seguridad para bebés hay un indicador del nivel para ayudar a reclinar debidamente el sistema de seguridad para bebés/base en el asiento del vehículo. No inclinar debidamente el sistema de seguridad para bebés en el asiento del vehículo aumenta el riesgo de lesiones serias o la muerte.
Para ajustar la inclinación sobre la base: Gire la perilla en el sentido de las agujas del reloj hasta alcanzar el valor deseado para bajar el pie . Gire la perilla en el sentido contrario a las agujas del reloj para levantar el pie . Si todavía aparece la zona de color naranja en el indicador de nivel cuando el pie está completamente extendido, levante el pie y coloque una toalla enrollada debajo del pie SOLAMENTE hasta que aparezca la zona de color azul.
Verificación final de seguridad: Cada vez que sale en automóvil con su niño, EMPUJE HACIA ABAJO lenta pero firmemente la parte de arriba del sistema de seguridad para bebés para asegurarse que el cinturón del vehículo no se alarga y que el cinturón del vehículo o el LATCH esté sujetado apretadamente alrededor de la base/ sistema de seguridad para bebés .
Cuando la instala en un avión usando la base, instálela de la misma manera que en un automóvil con el cinturón de la cintura solamente dejando la traba totalmente abierta para permitir espacio para la hebilla. Si solamente usa el armazón, instálela siguiendo las mismas instrucciones que para un automóvil. Notifique a la aerolínea con anticipación que piensa transportar una silla a bordo. Úsela solamente en un asiento de la aeronave orientado hacia adelante.
8.3 Limpieza y mantenimiento PARA SACAR Y LAVAR LA ALMOHADILLA DEL SISTEMA DE SEGURIDAD PARA BEBÉS, siga las instrucciones en la sección 5.1 “Colocación de las correas del arnés”, en las páginas 20 a 23 para sacar las correas del arnés de la placa de unión de metal. Separe la pequeña lengüeta que mantiene las hebillas del anclaje en su lugar y saque las hebillas del anclaje de sus hendiduras. Saque las hebillas de anclaje de las correas del arnés y pase las correas por las ranuras del asiento .
LAS PIEZAS DE METAL Y DE PLÁSTICO DEL SISTEMA DE SEGURIDAD PARA BEBÉS pueden limpiarse con una solución de jabón suave y agua. NO USE BLANQUEADOR NI DETERGENTE ya que podría afectar a las piezas de plástico. LAS CORREAS DEL ARNÉS pueden limpiarse a mano o cambiarse. NO SUMERJA LAS CORREAS DEL ARNÉS EN AGUA. Hacerlo podría debilitar las correas del arnés. NUNCA planche las correas del arnés. SI LAS CORREAS DEL ARNÉS están cortadas, deshilachadas o muy torcidas, debe cambiar las correas.
8.3.1 Proceso de limpieza de la hebilla PREVENGA LESIONES GRAVES O LA MUERTE: La hebilla debe abrocharse correctamente. Inspeccione y limpie la hebilla periódicamente para quitar objetos o desechos que podrían impedir la sujeción. 1. De vuelta el sistema de seguridad, pase el retén por la ranura de la correa de la entrepierna . 2. Para limpiar la hebilla, póngale en una taza de agua tibia y agite suavemente la hebilla, oprima el botón rojo varias veces mientras esté sumergida en el agua .
Notas 47
Para comprar piezas o accesorios o para obtener información sobre la garantía en los Estados Unidos, por favor comuníquese con nosotros en: Piezas de repuesto www.gracobaby.