Leeson Motor Field Installation for 7-1/2 HP Load and 7-1/2 HP Unload Applications Motor Kit Part No.: D04-0655 Instructions for replacing present 7-1/2 HP Baldor motors with Leeson 7-1/2 HP motors. NOTE: The Leeson motors do not have manual resets, so no bypass wiring is required.
PNEG-1765 Leeson Motor Field Installation for 7-1/2 HP Load and 7-1/2 HP Unload Applications
Table of Contents Contents Chapter 1 Safety .................................................................................................................................................. 4 Safety Guidelines ............................................................................................................................... 4 Chapter 2 Installation .........................................................................................................................................
1. Safety Safety Guidelines This manual contains information that is important for you, the owner/operator, to know and understand. This information relates to protecting personal safety and preventing equipment problems. It is the responsibility of the owner/operator to inform anyone operating or working in the area of this equipment of these safety guidelines. To help you recognize this information, we use the symbols that are defined below. Please read the manual and pay attention to these sections.
1. Safety Follow Safety Instructions Carefully read all safety messages in this manual and safety signs on your machine. Keep signs in good condition. Replace missing or damaged safety signs. Be sure new equipment components and repair parts include the current safety signs. Replacement safety signs are available from the manufacturer. Learn how to operate the machine and how to use controls properly. Do not let anyone operate without instruction. Keep your machinery in proper working condition.
1. Safety Stay Clear of Rotating Idler Entanglement in rotating idlers can cause serious injury or death. Keep all shields and covers in place at all times. Wear close fitting clothing. Stop and lock out power source before making adjustments, cleaning, or maintaining equipment. Entanglement Hazard Wear Protective Clothing Ear plugs or muffs should be worn at all times to protect ears from high noise levels. Wear close fitting clothing and safety equipment appropriate to the job.
2. Installation Top Auger Motor Step 1: (See Figure 2A.) 1. Remove the belts and sheave from the motor shaft. 2. Replace the present 712-1 Baldor motor with the D03-1010 Leeson motor. 3. Install new 28138-2 sheave on motor shaft. 4. Re-install belts and adjust tension. 5. Re-install belt guard.
2. Installation Bottom Auger Motor Step 2: (See Figure 2B.) 1. Disassemble auger cleanout handle mechanism to provide easier access to the motor. 2. Remove belts and sheave from motor shaft. 3. If the dryer is an FFI model with 7" metering rolls, replace the meter roll pan lever with D01-2605. (See Figure 2C on Page 9.) This will resolve any interference with the new motor. 4. Replace the present 712-1 Baldor motor with the D03-1010 Leeson motor. 5. Install new 28138-2 sheave on motor shaft. 6.
2.
2. Installation Cleanout Door Mechanism Step 3: (See Figure 2D below and Figure 2E on Page 11.) 1. To allow adequate clearance between the linkage arm and the motor, move the handle to the left side of the pivot arm weldment. 2. Also, move the linkage arm to the left side of the cleanout door hinge. (See Figure 2E on Page 11.) 3. Adjust linkage for correct operation of the cleanout door. Part No.
2.
2.
3. Warranty GSI Group, LLC Limited Warranty The GSI Group, LLC (“GSI”) warrants products which it manufactures to be free of defects in materials and workmanship under normal usage and conditions for a period of 12 months after sale to the original end-user or if a foreign sale, 14 months from arrival at port of discharge, whichever is earlier.
This equipment shall be installed in accordance with the current installation codes and applicable regulations which should be carefully followed in all cases. Authorities having jurisdiction should be consulted before installations are made. GSI Group 1004 E. Illinois St. Assumption, IL 62510-0020 Phone: 1-217-226-4421 Fax: 1-217-226-4420 www.gsiag.
