Assembly Instructions 34 18 " " 2-person assembly PH #2 51 ¼" Model # Finish GP0703 Brushed White GP0716 Brushed Driftwood GP0740 Brushed Grey Thank you for choosing Grain Wood Furniture, it is an honor to be in your home! If you have any questions, feedback, or need replacement parts please contact us at: grainwoodfurniture.com/help or support@grainwoodfurniture.
PLEASE READ BELOW BEFORE BEGINNING ASSEMBLY Ÿ Enlist help from a friend or family member as most items require two people for proper assembly. Ÿ Choose a spacious, open area near where the piece will be located once assembled. It is easier to move parts than to relocate the furniture after it is fully assembled. Ÿ Do not throw away packaging material until assembly is complete.
HARDWARE LIST A1 4,0x30 A4 3,5x14 A25 M4x25 B31 6,0x10 C2 8,0x25 RIGHT Side E13 61 + 2 16 + 1 10 + 1 40 + 2 ANTI-TIPPING RESTRAINT KIT A8 3,0x20 2+1 F8 2 F9 1 62 + 2 5 330mm - 13" Drawer RIGHT E13 5 330mm - 13" LEFT Side E14 5 330mm - 13" Drawer LEFT E14 5 330mm - 13" G1 G11 H11 10x10 26 4 10 ! ATTENTION Before starting assembly please verify the hardware set is complete. For missing hardware please contact us at grainwoodfurniture.
01 07 15 04 07 02 17 03 16 09 12 05 11 08 10 13 Part # 01 02 03 04 05 07 08 09 10 12 13 15 16 17 HW Box A - 1 of 2 Description Right side Left side Upper crosspiece Lower crosspiece Back panel Drawer front Drawer right side Drawer left side Drawer bottom Drawer back Drawer bottom support Profile “H” Rear panel Stabilizing panel Hardware 5x Qty.
C2 01) Tip : Use a hammer in case dowels are hard to install by hand.
Attention: There are no predrilled holes for the A1 screws on parts 02 and 03. 03) A1 04 02 A1 16 02 A1 A1 A1 17 04 A1 A1 16 A1 A1 A1 03 A1 A1 A1 05 A1 4,0x30 A1 14 04) Attention: There are no predrilled holes for the A1 screws on part 01.
Make sure back panels are perfectly aligned with side panels and top and there are NO gaps.
07) 07 15 07 15 G11 G11 G11 G11 4 G11 08) G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 10x10 18 page 8/13
09) A4 07 A4 A4 07 A4A4 A4 A4 16 Attention: There are no predrilled holes for the A4 screws on parts 07 and 16. A4 3,5x14 6 10) A4 A4 A4 A4 A4 A4 A4 A4 A4 A4 A4 Attention: There are no predrilled holes for the A4 screws on parts 02 and 03.
11) 5x 10 A1 09 A1 A1 08 11 Attention: There are no predrilled holes for the A1 screws on part 08.
Flip the assembled drawer upside down to install glides.
14) Place the labeled drawer on the top position ! page 12/13
ANTI-TIPPING RESTRAINT KIT 15) ! Install against the furniture A8 on the wall A8 F8 F8 F9 WALLBOARD Anchors and screws are not included, choose best type based on your wall F8 A8 3,0x20 2 F8 2 F9 1 WALLBOARD Install both parts F8 Tighten them together using the safety strap page 13/13