INSTRUCTION & USER MANUAL GRAND CRU BUILT-UNDER SERIES WINE COOLERS GC46D BUILT-UNDER SERIES BEVERAGE COOLERS GC46BC This manual contains important information including safety and installation instructions of the appliances. Please read it carefully before use and follow al safety information & instructions. It is recommended to keep this manual for easy reference so that you can be familiar with the operation of the appliance.
--CONTENTS-IMPORTANT SAFETY INFORMATION .............................................................................. 1 STRUCTURE AND INSTALLATION ................................................................................... 2 ACCESSORY INSTALLATION BEFORE OPERATING ..................................................... 3 UNPACKING AND CLEANING THE WINE COOLER ....................................................................................... 3 OPERATING THE WINE COOLER ..........................
IMPORTANT SAFETY INFORMATION Before using the appliance, please properly position and install it as described in this manual. To avoid the risk of fire, electrical shock or injury when using the appliance, please follow these basic precautions: • The appliance is intended to be used exclusively for the storage of wine. • Make sure the voltage/current marked on the rating label corresponds with your supply voltage. Plug into a standard 10amp 3-pin outlet.
STRUCTURE AND INSTALLATION The following pictures only show the structure of the appliance. The dimension and shelf quantity may differ among the models of the same series.
ACCESSORY INSTALLATION BEFORE OPERATING UNPACKING AND CLEANING THE WINE COOLER • Remove the exterior and interior packing materials. • Let the appliance stand upright for approximately 24 hours before connecting it to the power source, which helps to reduce the possibility of a cooling-system malfunction from handling during transportation. • Use a soft cloth to clean the interior surface with lukewarm water.
• To prevent damaging the door gasket, make sure to have the door opened fully all the way before pulling the shelves out. • Please store wine in sealed bottles. • Do not cover the shelves with aluminum foil or any other shelf material which may prevent air circulation.
POWER ON/OFF CONTROL • When the appliance is plugged in to a power outlet, it powers on automatically. • Touch the power mark and hold for 10 seconds to turn off (or turn on) the appliance. • No matter whether the appliance is under a locked or unlocked situation, you can turn off the appliance by touching the power mark and holding for 10 seconds. Warning: To avoid breaking the compressor, please do not turn on the appliance again within 5 minutes after you turn it off.
bottom zone. • You need to select the set zone by touching the mark before touching the mark or to set the desired temperature. The display window with digital flashing indicates the zone ready for temperature setting. or will recall the previous set temperature displayed in the digital window • The first touch on mark to increase the set temperature by 1ºC (or by 1ºF). On the contrary, touch the mark • Touch the mark to decrease the set temperature by 1ºC (or by 1ºF).
ENERGY SAVING TIPS • The appliance should be located away from heat producing appliances, and away from direct sunlight. • Ensure that the unit is adequately ventilated. Never cover the air vents. • Only open the door when necessary. Avoid leaving the door open for long periods or opening/closing the door frequently. TROUBLESHOOTING If you feel the appliance is out of order, follow these instructions to try to see if you can solve the problem simply by yourself before calling for service. No.
REVERSE THE DOOR SWING Remarks: • The instruction is based on a unit with right door hinge installed already. •To reserve the door from right hinge to left hinge, you need to get ready 2 new spare parts: an Upper Left Hinge, and a Bottom Left Hinge. * All removed parts is suggested t be saved in case of door re-reversal. 1．Open the door, and loosen the screws from the support rod of the bottom hinge. 2．Remove the door off the upper hinge and take out the support rod. 3.
5. Pry out the plastic caps at the left side of the cabinet, and remove them to the right side. 6. Install the hinge set which are packed as accessories with the instruction manual to the opposite side. 7. Rotate the door 180o so that the top is now the bottom, and install it by attaching the support rod with screws.
10
