Installation Guide

ManualsBrandsGrandeur ManualsDoor HardwareArc Antique Pewter 1-Piece Door Handleset with S Grip and Bellagio Handle - Left Handed

For assistance call 800-522-7336 Monday through Friday 7am to 5 pm Mountain Time

PK180 10062017

USE INCLUDED DOOR PREPARATION

TEMPLATE FOR NON-PREPPED DOORS.

USE INCLUDED PLASTIC TEMPLATE TO

LOCATE AND DRILL THE TWO TALL PLATE 1/4”

MOUNTING HOLES, AND THE 1/4” BOTTOM GRIP

MOUNTING HOLE. (See note on reverse side.)

1/4”

Tall Plate

Mounting

Holes

Bottom

Grip

Mounting

Hole

13A

Install deadbolt and

handleset latches.

Tongue

(See D Below

Before Deadbolt

Latch Installation.)

(See Latch

Tongue Note

in Panel C)

3/4”

Latch Tongue

Note

Bevel Side

Face Plate Curve

Strike Plate Curve

Bevel side of latch tongue should

contact curved end of face plate,

and curved end of strike plate.

Deadbolt Latch

Tongue Note

Door Inside

Intall screw

extenders

into

exterior

plate.

Tighten

securely.

Screw

Extenders

(part #8)

Install cylinder into

exterior plate.

Cylinder

Assembly (part #3)

Door Inside

2”

Cylinder

Insert cylinder

into exterior plate,

and place exterior

plate on

door outside.

Attach deadbolt

adaptor plate

with provided

screws.

DO NOT FULLY

TIGHTEN

THESE

SCREWS.

Insert

bottom grip

mounting

screw.

DO NOT

FULLY

TIGHTEN

THIS

SCREW.

Wait to

install the

mounting

screw

cover

until you

have

completed

step K.

Bottom Grip

Mounting Screw

(part #21)

1-1/2”

Adapter Plate

Machine Screws

(part #18)

Adapter Plate

(part #17)

Install

adapter

plate.

DO NOT

FULLY

TIGHTEN

THESE

SCREWS.

Slide

handleset

up, hold,

and

tighten

deadbolt

screws.

Tighten

adapter

plate

screws.

Check

operation by

pressing the

thumbpiece

down.

Tighten

bottom grip

mounting

screw

and check

operation

again.

Install bottom

mounting screw

cover.

Thumb-

piece

Attach

tall plate

with included

screws.

Check deadbolt

operation by

turning thumbturn

and key.

Check knob/lever

operation. Latch

tongue should

retract and extend

smoothly.

Install jamb strike plate.

Door

Jamb

3/4

Note: Handlesets fit doors 1-3/4” to 2” thick.

Single Cylinder Handleset

TALL PLATE

with

ONE-PIECE EXTERIOR PLATE

Grandeur

Door Hardware

Installation Instructions

Summary of content (2 pages)

PAGE 1
Grandeur Door Hardware Installation Instructions TALL PLATE with ONE-PIECE EXTERIOR PLATE Single Cylinder Handleset Note: Handlesets fit doors 1-3/4” to 2” thick. Install deadbolt and handleset latches. USE INCLUDED DOOR PREPARATION TEMPLATE FOR NON-PREPPED DOORS. Latch Tongue Note Tongue Bevel side of latch tongue should contact curved end of face plate, and curved end of strike plate. 14 3/4” 1/4” 2 Tall Plate Mounting Holes (See D Below Before Deadbolt Latch Installation.
PAGE 2
. Use position of small holes (B) to mark and drill 1/4” holes through the door. 1. Push plastic template’s large circles (A) into existing bore holes of door. B B B A A B Part Description 7 6 17 5 22 21 18 Edge-Bore Holes Cross-Bore Holes For assistance call 800-522-7336 Monday through Friday 7am to 5 pm Mountain Time Deadbolt Latch 1A. Latch Tongue 2. 3/4″ Faceplate & Strike Wood Screws (8) 3. Cylinder Assembly (W/Keys) 3A. Cylinder Body 3B. Tailpiece 4. One-Piece Exterior Plate 5.