Instructions / Assembly

D) Measure the thickness of the door. Doors vary in thickness
depending on the manufacturer. Determine the distance to
the center of the edge of the door (half the thickness of the
door). Using the awl (or nail), mark a point on the edge of the
door where the centerline pencil mark (from Step 1C) and the
center of the edge of the door meet (half the thickness). See
Figure #3.
Step 2
Drill the Door
A) Usingthe2-1/8″holesaw,drillthecrossboreholecentered
on the mark made on the face of the door from Step 1B. See
Figure #3. Important: To avoid splintering or marring the
door,drillfromonesideofthedooruntilthepilotbitcomes
through the door. Then drill from the other side of the door,
usingtheholemadebythepilotbitasyourguideuntilthe
crossboreholeiscomplete.
B) Usingthe1”bit,drilltheedgeboreholecenteredonthemark
made on the edge of the door where the centerline and center
thickness met from Step 1D, see Figure #3. Important:
Makesurethatyoudrillafull3-1/2″deeptoaccommodate
theoveralllengthofthe2-3/8″latch.Ifyouareusinga2-3/4″
backsetlatch,thentheoveralldepthmustbeatleast3-3/4″.
3-1/2″
2-3/8″
2-3/4″
3-3/4″
For 2-3/8″ Backset
For 2-3/4″ Backset
Cross Bore
Hole - 2-1/8″
Diameter
Mark from
Step 1B
Edge Bore
Hole - 1″
Diameter
Mark from
Step 1D
Door Thickness
Faceplate
Mortise
Area
Centerline
Mark from
Step 1C
Minimum
5-1/2
″ to center
line of door-
knob cross
bore hole
Door Hardware
Installation Instructions
Single Cylinder Deadbolt
NOTE: Deadbolts t doors 1-3/4” to 2-1/4” thick.
For thicker doors, please call customer service.
Carefully unpackage all components and place them within easy
reach. Find Figure #1 on Page 5 of these instructions for a listing
and drawing of each component. Detach Figure #1 and place
besidethecomponentsforeasyreference.Checkyourdoorto
seeifithasbeenprepped(pre-drilled)forinstallingadeadbolt.
Ifyourdoorhasbeenpreppedforinstallation,startatStep4.If
yourdoorhasnotbeenpreppedforinstallation,youwillneeda
#2Phillipsscrewdriver,adrill,a2-1/8″holesaw,adrill,a7/64″
drillbit,a1″drillbit,achisel,apencil,tapeandanawl(ornail).
Step 1
Mark the Door
A) Locate the Door Preparation Template which is included
with these instructions. Fold the template along the “edge-
of-door” line. Important: Before positioning the template,
make sure that you are aligning it on the non-hinged edge of
the door. Carefully position the template so that the narrow
portion of the template wraps around the edge of the door,
and the large portion of the template remains on the face
of the door, see Figure #2. Slide the template up or down
on your door so that the horizontal centerline is located at
aheightthatisattractiveinappearanceandatleast5-1/2″
abovethecenterofthedoorknobhole.Onceyouhavechosen
the height, tape the template to the door.
B) Thebacksetisthedistacefromtheedgeofthedoortothe
centerofthecrossborehole.Standardbacksetsare2-3/8″
and2-3/4″.Determinethebacksetofthedeadboltlatch(Part
#1)bycheckingthemarkingonthelatchitself.Ifthelatch
isnotmarked,measurethelatchbetweenpointsAandB
todeterminethebackset,asshowninFigure #2.Onceyou
knowyourbackset,ndthepointonthetemplatewhere
the centerline crosses the vertical line that corresponds with
thecorrectbackset.Usingtheawl(ornail)markthispoint,
making sure that it is marked well enough to see on the door
once the template is removed.
C) Follow the centerline around the edge of the door and using
a pencil, extend the centerline onto the edge of the door. The
markshouldbeparalleltotheoor.Oncethismarkismade,
you may remove the template from the door.
Page1-PK147
For
Assistance
Call:
1-800-522-7336
8 am - 5 pm, Monday - Friday, MST
(A)
(B)
Template
Edge
of
Door
Face of Door
Centerline
Latch
Backset
Measurement
2-3/8” or 2-3/4”
Figure #2
Figure #3