GRANDIO ® G R E E N H O U S E S GRANDIO ELITE 8x8 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION STOP Grandio Elite 8x8 Shown In Image This manual is for an 8x8 Grandio Elite Kit. GREENHOUSE USER MANUAL If building an 8x12, 8x16, 8x20, or 8x24 refer to that manual. © 2013 Grandio Greenhouses, Backyard Living Source Inc.
GRANDIO ® G R E E N H O U S E S Dear Valued Customer, We would like to congratulate you on your new Grandio Greenhouse purchase. We are confident that you have made the right decision in choosing Grandio. Our greenhouses are made with high quality aluminium and polycarbonate and will last for many garden seasons to come. Please take the time to carefully read this instruction manual for an easier and more enjoyable assembly experience.
IMPORTANT! SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction materials. Before beginning assembly, read the instructions and identify all parts using the hardware identifier and parts list on pages 46-50.
PREPARE A FOUNDATION FOR YOUR GRANDIO GREENHOUSE Before assembling your new greenhouse, a proper foundation must be prepared. A number of anchoring options are acceptable, based on wind and ground conditions in your area. Pre-read pages 6-9 for base kit assembly information. 8X8 GRANDIO ELITE BARN STYLE GREENHOUSE DIMENSIONS ROOF PEAK HEIGHT Go to www.grandiogreenhouses.com for foundation ideas and tour our online learning center for tips, tricks and videos for putting your greenhouse together.
BACK L08A 606-WS L08B-X 606-WS 606-WS DIAGRAM SHOWS THE ASSEMBLED (8’x8’ BASIC CONFIGURATION) (GRA-ELI-8A & GRA-ELI-8P & GRA-BA-8) 8x8 ELITE KIT INCLUDES, FRONT, BACK, BASE AND SIDES.
GRANDIO ® G R E E N H O U S E S ASSEMBLY INSTRUCTION STEPS Introduction............................................................1 PREPARE FOR ASSEMBLY Safety Instructions...............................................2 Prepare For Assembly..........................................3 STEP ONE: BASE ASSEMBLY Diagram of Assembled Grandio Elite 8x8......4 Base Kit Assembly Information........................6 Base Kit Parts Lists...............................................
BASE KIT ASSEMBLY INSTRUCTIONS Pre-Plan The Placement Of Your Structure Allow enough room to get a wheel barrow in and around your structure. Be sure the orientation will allow for proper drainage in and around your greenhouse. It is recommended that you place your greenhouse in an area of your property that receives the most sunlight but is also somewhat protected by trees, fencing or your home for wind protection and also to keep the temperature up during early spring and late fall.
BASE KIT PARTS LIST FOR 8’X8’ GRAPHIC PART NAME SIZE/LOCATION QUANTITY BA-S1 97 3/8 in / 2474 mm 2 BA-S2 94 1/4 in / 2394 mm BA-C3 5 7/16 in 138 mm GRAPHIC PART NAME SIZE/LOCATION QUANTITY BA-S03 M6*14 28 2 ML01 BOLT 28 4 W05 CLIP 9 1.1 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one will be at the back and the BA-S2’s will be on the sides. See diagram .
BASE KIT ASSEMBLY INSTRUCTIONS 1.2 Slide the BA-C3 into the BA-S1, slide the BA-S2 into the BA-C3, align the holes and push together to an even and tight position and use the BA-S03 bolt and ML01 collard nut combo, tighten the collard nut on the inside of the base kit using the 10mm wrench or nut driver. Repeat this process on all corners. See and . Note: Placement of BA-S1 will be at front and the back, while the BA-S2’ s will be the sides of your greenhouse base. 1.
BASE KIT ASSEMBLY INSTRUCTIONS **BASE MUST BE LEVEL & SQUARE, FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY Holes are present for BA-A1 / L-BOLT in ground anchoring system. You determine Holes are present in base kit for anchoring bolts for concrete pad or wood deck installation. You determine and aquire proper fastener prior to installation. and aquire proper fastener prior to installation.
FRONT FRAME ASSEMBLY INSTRUCTIONS ALWAYS ASSEMBLE FRONT HORIZONTAL This picture shows the inside view of front section fully assembled. All parts for front assembly will be found in box GRA-ELI-8A and GRA-ELI-8P. We recommend that you assemble the front on a tarp. * If you purchased the Back Door Transformation kit you will repeat this section for your back wall using parts found in the GRA-ELI-BD, GRA-ELI-8A and GRA-ELI-8P boxes.
FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL 2.1 Prethread all S05 screws into the WG01 and WG02’s for ease of installation, see only turn S05 a few turns. Leave the mid hole open, as this is for the end cap attachment. S05 601B 2.2 Use WG01 bracket to attach the (2) 601B’s together with the 603E, secure parts with the S05 screws provided see . The WG01 will slide into the groove of the 601B’s, and also slide into the groove of the 603E, screw head will remain outside channel.
FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL *IF USING THE MOISTURE CONTROL KIT YOU WILL USE IT NOW 2.4 Insert polycarbonate panels Y3-2 and . WG01 601B WG02 2.5 Attach 603E and 603D with W04 and S04/ML01 fasteners as shown in WG02 603E . Y3-2 601B 2.6 Attach the 603D to the 601B’s using the W04-1’s with the S04/ML01 fasteners on both sides as shown in .
FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL 2.7 View diagrams and attach the (2) 604’s and (2) 601A’s to the 619. Note the orientation of the 604’s, there are 4 different 601A’s (2) for the front and (2) for the back with different hole placements. See diagram on this page. The 601-FR and the 601-FL will have a hole at the top side and will face forward. 604-R OUTSIDE INSIDE shows where the corner pieces attach to 619.
FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL 2.8 Attach 606-WS to 619, this will hold the polycarbonate panels in place. If it seems too tight slide fingers or nut driver along edges, gently stretching the 606-WS to allow room for panels to fit . Polycarbonate panel OUTSIDE 606-WS 619 604-R 604-L Y1 2.9 Insert Y1 polycarbonate panels into place, make sure Y1’s slide completely into 606-WS as shown in . Y1 601A-FL 601A-FR 2.
FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL 2.12 Move roof and front section together and align the WG02’s into the 601A’s, and the W04-2’s into the 604’s. Insure a snug fit between the WG02’s, 601B’s and 601A’s and then tighten the S05 screw as shown in . Tighten the W04-2’s with the S04 /ML01 nut and bolt as shown in .
BACK ASSEMBLY INSTRUCTIONS ALWAYS ASSEMBLE BACK HORIZONTAL This image shows the inside view of the back wall assembly. All parts for back assembly will be found in box GRA-ELI-8A and GRA-ELI-8P. We recommend that you assemble the back wall on a tarp. * If you are using the Back Door Transformation Kit you will skip this section.
BACK CONTINUED ALWAYS ASSEMBLE BACK HORIZONTAL 3.1 Prethread all S05 screws into the WG01 and WG02, see . Leave mid hole open it is for endcap attachment. FAT END FAT END WG02 3.2 Use the WG01 bracket to attach the WG01 WG02 S05 601B 3.3 Install WG02’s to connect (2) 601B’s when firmly placed between the extrusions tighten the S05 screws, see . WG02 WG01 601B 601B 601B STEP THREE STEP THREE (2) 601B’s together, secure parts by sliding the WG01 into the 601B’s as shown in diagram .
BACK CONTINUED ALWAYS ASSEMBLE BACK HORIZONTAL 3.4 Attach (2) 601A-B’s to L08A using S04/ML01 fastener as shown in diagram . Attach (2) 602D’s to L08A using S04/ML01 fasteners as shown in diagram . Y1 3.5 Attach the (4) 606-WS’s to the L08A as shown in . 3.6 Insert the Y1 polycarbonate panels into the 601A-B Y1 Y1 602D grooves of 601A, 602D and 602C. Make sure Y1 panels are inserted into 606-WS as shown in .
BACK CONTINUED ALWAYS ASSEMBLE BACK HORIZONTAL 3.7 Set (4) 603C’s atop each Y-1 panel, then align the pre threaded S04-ML01 fasteners in each 603C to the L08B and to each 601A-B, 602D and the 602C. When aligned tighten the middle first and work your way outward. See diagrams , , . Y4-2 3.8 Insert the Y5-1 and Y5-2 polycarbonate panels Y5-2 Y5-1 Y4-1 STEP THREE into place. Then insert the Y4-1 and Y4-2 into place as shown in the diagram.
BACK CONTINUED ALWAYS ASSEMBLE BACK HORIZONTAL WG01 WG02-’s and the S04/ML01 W04-2’s brackets and place into appropriate extrusion see , and . Align WG02’s into 601A’s, the W04-2’s into 602D’s, and the WG01 into the 602C. When all members are snug tighten all fasteners to lock into place.
BACK CONTINUED ALWAYS ASSEMBLE BACK HORIZONTAL 3.10 A. Attach (2) L08B-X’s to (2) 602D’s and L08A with S04/ML01 as shown in . STEP THREE B. Attach (2) L08B-X’s to the (2) 601A-B’s with fasteners as shown in . 602D L08B-X 602C L08B-X 601A-B 602D 602D S04/ML01 L08A Inside View ML01 S04 Square by loosening bolts T I P attached to the tops of the L08B-X, use measuring tape to make sure corner to corner measures the same.
MIDDLE ASSEMBLY INSTRUCTIONS BA-S1 STEP FOUR If building a greenhouse with a front and back door you will repeat steps 4.1-4.5 for attaching both front and back walls of the greenhouse, and you will skip step 4.6-4.8. Warning: The person(s) holding the 601A front or back sections vertical must continue to do so until the L08C-X angle ML01 S04 supports are attached securely to the ML01/ BA-S2 front and base as shown in step 4.5.
MIDDLE ASSEMBLY CONTINUED 4.3 Attach L08C-X to 601A and the BA-S2 with S04/ML01 on both sides as shown in STEP FOUR and with the nut and bolt combos. 4.4 Attach the front section 619 to the base using (3) S10/ML02 fasteners as shown in , then attach the threshold support 619-BAR to the inside of the 619 with (5) S19 self tapping screws included in the package, see .
MIDDLE ASSEMBLY CONTINUED If you are using the Back Door Transformation kit you will repeat steps 4.1-4.5 to install the Back Door Wall, then skip ahead to step 4.9. W05/S04/ML01 fasteners as shown in , and . The (4) W05 clips will catch the under edge of the front base kit and then slide upward attaching to the bottom of the 601A’s and the 604’s.
MIDDLE ASSEMBLY CONTINUED 4.6 Attach back wall 601A’s with back base corners using S04/ML01 on both sides as shown in 4.7 Attach bottom of L08C-X to rear section of base kit with S04/ML01, as shown in as shown in , make sure the S04/ML01 combos are tight. . . Attach the L08C-X to the 601A STEP FOUR 4.8 Use the (5) remaining W05 clips to attach the backwall where the 601A’s meet the corner of the base as shown in and where 602D’s, and the 602C meet the BA-S1B see .
MIDDLE ASSEMBLY CONTINUED 4.9 With 2 people, attach the ridge to front and back by sliding into place as Side Angle View , using S04/ML01 fasteners attach the 607 to the 601B’s 607 STEP FOUR shown in and as shown in .
MIDDLE ASSEMBLY CONTINUED 4.10 Before you attach the 609 you will need to loosen the STEP FOUR ML01 (nut) attached to the tops of the L08C-X. Note: Loosen nuts on only one side at a time, i.e. right front corner, right rear corner. See . Inside View Inside View LOOSEN ML01 With 2 people proceed to install 609’s in this order, note that 609 must be installed with groove side down see . Compare with 610 to make sure it will slide into 609 upon completion. L08C-X 601B 601A L08D OR L08B 609 1.
MIDDLE ASSEMBLY CONTINUED 4.11 Note orientation of the 609, see . . STEP FOUR 1. Attach the mid roof 609’s with S04/ML01 nut and bolt on both sides see 609 Profile View 602B Note the line on the 609 that shows the exact placement of UP the 602B’s and the 602A’s when installed correctly. Groove 609 602A 601B 1 2 601A Inside View FRONT 609 601B ML01/S04 Remove only one L08C-X at a time. If all L08C-X’s are removed, the structure will collapse and cause unwarrantable damage.
MIDDLE ASSEMBLY CONTINUED STEP FOUR 4.12 Before you attach the 602A’s to the sides of the greenhouse you will need to loosen the ML01 (nut) attached to the L08C-X and the base. See diagram . 609 601B 1. Once the bottom of one L08C-X is loosened set the 602A onto the bolt of the the L08C-X. Be sure that the 602A is sitting flush on top of the base kit. See for reference. 2. Hold the 602A in place and attach the top of the 602A to the 609 using S04/ML01 (nut and bolt). As shown in . 3. Repeat steps 1.
MIDDLE ASSEMBLY CONTINUED 4.13 Install plastic strip 606-WS before inserting polycarbonate sheet Y7’s, see . STEP FOUR 4.14 After Y7’s are installed on both sides, loosen bolts attached to L08C-X in all upper corners. Using a level, adjust 602A and tighten bolts. Repeat in every corner until the greenhouse is plumb. The top edges of Y7’s will align when greenhouse is level or plumb.
MIDDLE ASSEMBLY CONTINUED 4.15 Attach 602B’s to 609’s and 607’s as shown in STEP FOUR diagram on both sides of the upper roof section. Note the exact placement on the outside see . 607 609 Attach (1) 602B between the (2) 609’s, in the middle only on both sides of roof. Do not attach remaining 602B’s to lower roof section until roof vents are attached, see .
MIDDLE ASSEMBLY CONTINUED 4.16 Insert Y11 panels to upper roof section then slide the 630 into the groove of the upper 609 as shown to hold Y11’s in place. See and . Note that you may need to loosen the bottoms of some of the 602B’s to slide the 630 into place as the fit is very tight. Check that all nut and bolt combos are tightened again after installation of 630. 607 609 Y11 Y11 4.
MIDDLE ASSEMBLY CONTINUED 4.18 Assemble the roof window vents as shown below in STEP FOUR and , using the Z02 screws attach the 615, 616, and 618’s with the Y10 panel as shown, be careful not to strip the screw heads. Pay attention to the Y10 panel, stickers will face the sun. Y10 4.19 Insert assembled window into the end of ridge of 630 and slide Y10 into position. See .
MIDDLE ASSEMBLY CONTINUED 4.20 After roof vents are positioned, attach all remaining 602B’s and . Y10 602B Y10 602A 602A 602A Outside View 607 EXACT PLACEMENT 602B Profile View 602B 609 Groove 609 602A 602A Note the line on the 609 that shows the exact placement of UP the 602B’s and the 602A’s when installed correctly.
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED 4.21 To ensure there is no gap in roof vent 616 Inside view of 603C 603C position 603C as shown in . Connect 603C to middle of 602B’s using W04 bracket as shown in . 602B 4.22 Attach HQC01 to 616 with the Z04 screws see , close roof vent and attach the handle onto HQC02 middle pin (the first two holes of the handle to the second and third pins of HQC02). Then attach HQC02 into 603C’s track with S04/ML01 (nuts and bolts), see .
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED 4.23 Insert polycarbonate sheets Y8’s and Y9’s into the lower roof of your greenhouse. Panels may slide out before gutters are in place. You may want to place a piece of tape on the panel to prevent sliding as shown below once the panels are in place. 4.24 Slide 610 into 609’s groove as shown in diagram STEP FOUR tape after gutter is fully installed. . Repeat on both sides.
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED 4.25 Attach JG01, JG02A, JG02B, JG03A and JG03B end caps to the ridge, midroof JG02B JG01 Exterior view of mid roof cap JG01. JG03B Z03 Interior greenhouse view of mid roof cap, where Z06 screw goes through WG01 mid hole into the end cap. JG02A Z06 JG03A Z03 37 STEP FOUR and gutters on both front and back as shown below. Use Z03 screws to attach the JG03A and JG03B endcaps along with the silicone adhesive.
STEP FIVE DOOR ASSEMBLY DIAGRAM This image shows the inside view of Right Door Assembly. All parts for door assembly will be found in box GRA-ELI-8A and GRA-ELI-8P. Use the #2 head Phillips Screw Driver for installation. If you are using the Back Door Transformation kit you will repeat steps 5.1-5.11 to install the Back Door, these parts will be found in box GRA-ELI-BD.
We recommend you lay out all parts for both doors to make sure they match up correctly for hanging. Double check the orientation of what is inside verses outside and how the doors will hang on page 42-43. Make sure window panels face the right direction to the sun and note that the panels have predrilled holes for the handles to attach later and these need to be aligned with the lock mechanisms, if the holes are not present you will need to drill these out prior to installing the door handles.
STEP FIVE DOOR ASSEMBLY 5.4 Insert J08A into the bottom of the 622-R and 622-L, note the bottom has a groove see . 5.5 Attach the 622-R to the 623B, 623A and 620 using the Z01 screws as shown in . 5.6 Follow the same instructions for the other door making sure that the 622-L and 622-R with the double ball catch match up so doors will latch closed and slide properly . Z01 Side View Of Top Side View Of Top 622-L 622-R * Double Ball Catch on the 622-L * Note the orientation of the 622-L and 622-R.
5.7 Slide the (2) S02 bolts down the track of the L21, see . Align with the holes on the 603D door header. With one person inside the greenhouse line up hanging door track L21 with door header 603D, move bolts on L21 to line up with bolt holes on door header 603D. From the inside hand tighten the ML01 nut while the person outside is holding the L21 in position, you will now center on the front of the greenhouse and tighten the S02/ML01 combo.
STEP FIVE DOOR INSTALLATION 5.8 Separately slide the top of the doors in the left and right side of L21, see diagram , until they latch in the middle. 5.9 Attach the door handles 622-HNDL to both doors using the 622-HNDL-NUT/BOLT provided to both doors as shown below in , and . **We included some felt dots in your Grandio Welcome Kit, please apply to the inside bottom edge of the 623B as shown in these felt dots will make your doors fit snug and slide smoothly.
STEP FIVE DOOR INSTALLATION 5.10 Attach L28 to L21 with S04/ML01, and L28 to 601A with WASHERS and S02/ML01 as shown below in diagram and . Check that the L21 and L28’s are square. Attach (2) J07 to the ends of L21 see . The L28 should align square to the 601A. 5.11 Check that the door locks are snug, you may adjust them with screwdriver if needed as they may be tightened or loosened.
INTERIOR ROOF SUPPORT ASSEMBLY 6.1 Attach the L08E-X to the upper roof section as shown with S04/ML01 fasteners already in place where the 607 meets the 601B, and the 609 and the 602B meet see . 609 607 BZ-1 6.2 Attach the L08D-X to the rear lower roof 609 section where S04/ML01 fasteners are already in place where the 609 and the 602B meet, and the 609 and the 601B meet see . 6.3 Attach the BZ-1’s to the roof line as shown in diagram with the S04/ML01.
6.5 With two people attach the AZ-1 to the W17 to the base and the lower 602A, see . Then attach the upper end to the mid roof line touching the 609 see for exact placement. Install on both sides of the greenhouse in the middle using the S02/ML01 combo. 601B BZ-1 609 You may remove all stickers now with Goo Gone if needed. Double check all nut and bolt combos are tight and that there are no left over parts.
(GRA-ELI-8A) 8x8 GRANDIO ELITE ALUMINUM PACKING LIST GRAPHIC PART NAME GRAPHIC PART NAME SIZE/LOCATION QUANTITY SIZE/LOCATION QUANTITY 56 9/16 in / 1437 mm 2 604-R 70 3/4 in / 1797 mm FRONT RIGHT 1 FRONT LEFT CORNER 1 604-L 70 3/4 in / 1797 mm FRONT LEFT 1 601A-FR 56 9/16 in / 1437 mm 1 607 94 1/4 in / 2394 mm 1 601B 29 7/16 in / 748 mm 8 606-WS 21 3/4 in / 553 mm 14 602A 56 9/16 in / 1437 mm 6 609 94 1/4 in / 2394 mm 4 602B 29 7/16 in / 748 mm 12 610 94 3/8 in / 2397
(GRA-ELI-8A) 8x8 GRANDIO ELITE ALUMINUM PACKING LIST GRAPHIC PART NAME SIZE/LOCATION QUANTITY GRAPHIC PART NAME SIZE/LOCATION QUANTITY L08D 24 3/16 in / 614 mm 2 AZ-1 / W17 S02/ML01 86 1/4 in / 2190 mm EXTENSION SUPPORT 2 L08A-X 52 1/4 in / 1327 mm 2 S02/ML01 M6*25 6 L08B-X 51 3/16 in / 1300 mm 2 S04/ML01 M6*14 150 L08C-X 61 1/32 in / 1550 mm 4 S05 M6*10 45 L08D-X 37 13/16 in / 960 mm 4 Z04, S04/ML01 ROOF VENT HARDWARE 4 L08E-X 38 11/16 in / 957 mm 4 HQC01 ROOF VENT
(GRA-ELI-8A) 8’x8’ GRANDIO ELITE ALUMINUM PACKING LIST GRAPHIC PART NAME SIZE/LOCATION QUANTITY GRAPHIC PART NAME SIZE/LOCATION QUANTITY 622-HNDL DOOR HANDLES 4 JG01 RIDGE END CAP 2 622-HNDL NUT/BOLT DOOR HARDWARE 4 JG02 A/B MID ROOF END CAP 2/2 620 21 7/16 in / 545 mm 2 JG03 A/B GUTTER END CAP 2/2 L21 95 1/2 in / 2425 mm 1 Z03 M3*25 4 J07 L21 END CAP 2 Z06 M4*10 10 622 69 11/16 in / 1770 mm 2 622-R 69 11/16 in / 1770 mm 1 622-L 69 11/16 in / 1770 mm 1 623A 21
(GRA-ELI-8P) 8’x8’ ELITE PANEL BOX PACKING LIST GRAPHIC NAME SIZE/LOCATION WIDTH HEIGHT 1 HEIGHT 2 QTY Y1 FRONT & BACK PANEL 22 3/4 in / 578 mm 47 5/16 in / 1202 mm Y2-1 FRONT PANEL 22 3/4 in / 578 mm 9 1/16 in / 230 mm 23 in / 585 mm 1 Y2-2 FRONT PANEL 22 3/4 in / 578 mm 23 in / 585 mm 9 1/16 in / 230 mm 1 Y3-1 FRONT PANEL 35 1/2 in / 902 mm 9 15/16 in / 252 mm 19 1/8 in / 486 mm 1 Y3-2 FRONT PANEL 35 1/2 in / 902 mm 19 1/8 in / 486 mm 9 15/16 in / 252 mm 1 Y4-1 BACK PAN
(GRA-ELI-BD) GRANDIO ELITE BACKDOOR PACKING LIST GRAPHIC PART NAME SIZE/LOCATION QUANTITY 603D 72 3/16 in / 1833 mm SIZE/LOCATION QUANTITY 1 Z01 M4*30 SCREWS FOR DOORS 13 603E 18 1/4 in / 463 mm 1 S04/ML01 M6*10 35 70 3/4 in / 1797 mm 1 S02/ML01 M6*25 4 604L 70 3/4 in / 1797 mm 1 L21 95 1/2 in / 2425 mm 1 L08D 24 3/16 in / 614 mm 2 J07 L21 ENDCAP 2 619 619-BAR S19 Screw S10 / ML02 94 1/4 in / 2394 mm 44 1/2 in / 1130 mm M4*10 M6*16 / NUT 1 - 619 1 - 619 Bar 5 - S19 Screw
Grandio Greenhouse Limited Lifetime Warranty 1. Grandio Greenhouses are warranted to the original purchaser to be free from defects in material or workmanship for ten years from the date of original retail purchase on all plastic panels. Additionally the aluminium frame is warranted for life. The word “defects” is defined as imperfections that impair the use of the product. 2. Defects resulting from misuse, abuse or negligence will void this warranty.
NOTES NOTES
GRANDIO ® G R E E N H O U S E S Grandio Elite 8x8 GREENHOUSE USER MANUAL KEEP IN A SAFE PLACE FOR REFERENCE CONTACT US IF YOU NEED HELP OR HAVE MISSING OR DAMAGED PARTS GRANDIOGREENHOUSES.COM BACKYARD LIVING SOURCE, INC. 9543 W. EMERALD ST.