Grandstream Networks, Inc.
This page intentionally left blank GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 Administration Guide
GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 Administration Guide Table of Content DOCUMENT PURPOSE ............................................................................... 4 GUI INTERFACE EXAMPLES ...................................................................... 5 GNU GPL INFORMATION ............................................................................ 6 CHANGE LOG .............................................................................................. 7 FIRMWARE VERSION 1.0.5.23 ......
CONFIGURATION VIA KEYPAD..................................................................................................... 23 CONFIGURATION VIA WEB BROWSER........................................................................................ 30 DEFINITIONS................................................................................................................................. 31 STATUS PAGE DEFINITIONS ..............................................................................................
Table of Tables GXP2130/GXP2140/GXP2160/GXP2170/GXP2135User Manual Table 1: GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 FEATURES IN A GLANCE........................ 13 Table 2: GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 COMPARISON GUIDE ............................. 14 Table 3: GXP2130 TECHNICAL SPECIFICATIONS ............................................................................... 15 Table 4: GXP2140 TECHNICAL SPECIFICATIONS ...............................................................................
DOCUMENT PURPOSE This document describes how to configure GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 features via phone‟s LCD menu and Web GUI menu. The intended audiencesof this document arephone administrators.To learn the basic functions of GXP2130/GXP2140/GXP2160/GXP2170/GXP2135, please visit http://www.grandstream.com/supportto download the latest “GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 End User Guide”.
GUI INTERFACE EXAMPLES http://www.grandstream.com/sites/default/files/Resources/gxp2130_2140_2160_web_gui.zip 1. Screenshot of Login Page 2. Screenshots of Status Pages 3. Screenshots of Accounts Pages 4. Screenshots of Settings Pages 5. Screenshots of Network Pages 6. Screenshots of Maintenance Pages 7.
GNU GPL INFORMATION GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 firmware contains third-party software licensed under the GNU General Public License (GPL). Grandstream uses software under the specific terms of the GPL. Please see the GNU General Public License (GPL) for the exact terms and conditions of the license. Grandstream GNU GPL related source code can be downloaded from Grandstream web site from: http://www.grandstream.com/sites/default/files/Resources/gxp_gpl_color.tar.
CHANGE LOG This section documents significant changes from previous versions of user manuals forGXP2130/GXP2140/GXP2160/GXP2170/GXP2135. Only major new features or major document updates are listed here. Minor updates for corrections or editing are not documented here. FIRMWARE VERSION 1.0.5.23 Updated logo for web UI FIRMWARE VERSION 1.0.5.18 Added more features descriptions for the MPKs mode – Monitored Call Park and Call Park sections.
Added option to download local call recordings. [SETTINGS PAGE DEFINITIONS] Added option to configure the color and pattern of the LED based on status updates. [SETTINGS PAGE DEFINITIONS] Added function to allow configuration of MPK or Line key to provide MWI for other extension. [SETTINGS PAGE DEFINITIONS] Added function to allow configuration of Call Log for other extension. [SETTINGS PAGE DEFINITIONS] Added MPK mode Monitored Call Park for other extension.
downloading. [PHONEBOOK PAGE DEFINITIONS] Added option to enable/disable the dial plan check while dialing through the call history and any phonebook directories. [SETTINGS PAGE DEFINITIONS] Added option to enable/disable the busy tone heard in the handset when call is disconnected remotely. [SETTINGS PAGE DEFINITIONS] Added XML Application support. [SETTINGS PAGE DEFINITIONS] Added Direct IP Call support on MPK and Phonebook.
Add Bluetooth handsfree mode.[BLUETOOTH] Added Configuration file upload support via Web UI. [MAINTENANCE PAGE DEFINITIONS] Add Screen saver support. [SETTINGS PAGE DEFINITIONS] Add Wallpaper support. [WALLPAPER] Addthe support of STAR key keypad lock feature. [MAINTENANCE PAGE DEFINITIONS] Add the support of Configuration via Keypad Menu.[MAINTENANCE PAGE DEFINITIONS] Add Keypad shortcut to reboot and provisioning.
GXP2135 FIRMWARE VERSION 1.0.6.6 This is the initial version.
WELCOME Thank you for purchasing Grandstream GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 Enterprise IP Phone. GXP2130/GXP2140/GXP2160/GXP2170/GXP2135is a state-of-the-art enterprise grade IP phone.GXP2170 features 12 dual-color line keys(can be digitally programmed as up to 48 provisionable BLF/fast-dial keys). GXP2135 features 8 dual-color line keys(can be programmed as up to 32 provisionable BLF/fast-dial keys). GXP2140/GXP2160/GXP2170 features 4.
PRODUCT OVERVIEW FEATURE HIGHLIGHTS Table 1: GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 FEATURES IN A GLANCE GXP2130 GXP2140 GXP2160 3lines 2.8 inch (320x240) TFT color LCD 4 programmable soft keys Bluetooth V2.1 (GXP2130v2 only) 8 programmable Multi-Purpose Keys 4-way conference 4lines 4.3 inch (480x272) TFT color LCD 5programmable soft keys Bluetooth V2.1 5-way conference Expansion board 6lines 4.
8 dual-color line keys that can be digitally programmed as up to 32 provisionable BLF/fast-dial keys GXP2135 2.8 inch (320x240) TFT color LCD 4 programmable soft keys Bluetooth V2.
GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 TECHNICAL SPECIFICATIONS Table 3: GXP2130 TECHNICAL SPECIFICATIONS Protocols/Standards SIP RFC3261, TCP/IP/UDP, RTP/RTCP, HTTP/HTTPS, ARP, ICMP, DNS (A record, SRV, NAPTR), DHCP, PPPoE, SSH, TFTP, NTP, STUN, SIMPLE, LLDP, LDAP, TR-069, 802.1x, TLS, SRTP, IPv6 Network Interfaces Dual switched auto-sensing 10/100/1000 Mbps Gigabit Ethernet ports with integrated PoE Graphic Display 2.8 inch (320x240) TFT color LCD Bluetooth Yes, Bluetooth V2.
Physical Dimension: 193mm (W) x 211mm (L) x 84.5 mm (H); Unit weight: 0.78kg ; Package weight: 1.
authentication, AES based secure configuration file, SRTP, TLS, 802.1x media access control Multi-language English, Arabic, Chinese, Croatian, Czech, Dutch, German, French, Hebrew, Hungarian, Italian, Japanese, Korean, Polish, Portuguese, Russian, Slovenia, Spanish, Turkish Upgrade/Provisioning Firmware upgrade via TFTP/HTTP/HTTPS, mass provisioning using TR-069 or encrypted XML configuration file Power & Green Energy Efficiency Universal power adapter included:Input:100-240VAC ; Output: +12VDC, 1.
flexible dial plan, hot desking, personalized music ringtones and music on hold, server redundancy and fail-over Sample Applications Weather, currency, GMI available for advanced custom application development HD audio Yes, both on handset and speakerphone Base Stand Yes, allow 2 angle positions Wall Mountable Yes QoS Layer 2 (808.1Q, 802.
Voice Codec Support for G.729A/B, G.711µ/a-law, G.726, G.
Table 7: GXP2135 TECHNICAL SPECIFICATIONS Protocols/Standards SIP RFC3261, TCP/IP/UDP, RTP/RTCP, HTTP/HTTPS, ARP, ICMP, DNS (A record, SRV, NAPTR), DHCP, PPPoE, SSH, TFTP, NTP, STUN, SIMPLE, LLDP, LDAP, TR-069, 802.1x, TLS, SRTP, IPv6 Network Interfaces Dual switched auto-sensing 10/100/1000 Mbps Gigabit Ethernet ports with integrated PoE Graphic Display 2.8 inch (320x240) TFT color LCD Bluetooth Yes, Bluetooth V2.
Unit weight: 0.98kg; Package weight: 1.
This page intentionally left blank GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 ADMINISTRATION GUIDE Page 22 of 85
CONFIGURATION GUIDE TheGXP2130/GXP2140/GXP2160/GXP2170/GXP2135can be configured via two ways: LCDConfiguration Menu using the phone's keypad; Web GUI embedded on the phone using PC's web browser. CONFIGURATION VIA KEYPAD To configure the LCD menu using phone's keypad, follow the instructions below: Enter MENU options. When the phone is in idle, press the round MENU button to enter the configuration menu; Navigate in the menu options.
(DHCP/Static IP/PPPoE), IPv4 address, IPv6 address, Subnet Mask, Gateway and DNS server. System Information Press to enter the sub menu for Hardware version, P/N number.Boot, Core, Base, Prog version and IP Geographic Information. Contacts Contacts sub menu includes the following options: Local Phonebook Local Group LDAP Directory Contacts sub menu is for Local Phonebook, Local Group, LDAP Directory and Broadsoft Phonebooks.
Adjusts active LCD brightness by pressing left/right arrow key o Idle LCD Brightness Adjusts idle LCD brightness by pressing left/right arrow key o Screensaver Enable/Disable Screensaver o Screensaver Timeout Configures the minutes of idle before the screensaver activates. Valid range is 3 to 6. Language and Input o Display Language Selects the language to be displayed on the phone's LCD. Users could select Automatic for local language based on IP location if available. By default, it is Auto.
Configures call forward features for Forward All, Forward Busy, Forward No Answer and No Answer Timeout. System System sub menu includes the following options: Network o IP Setting Selects IP mode (DHCP/Static IP/PPPoE);ConfiguresPPPoE account ID and password; Configures static IP address, Netmask, Gateway, DNS Server 1 and DNS Server 2. o 802.1X Enables/Disables 802.1X mode; Configures 802.1x identity and MD5 password. o Layer 2 QoS Configures802.1Q/VLAN Tag and priority value.
Configuresconfig server for provisioning the phone. o Upgrade Via Specifies upgrade/provisioning via TFTP/HTTP/HTTPS. o Start Provison Starts Provision immediately. Language Download o Auto Language Download o Language Download Factory Functions o Diagnostic Mode All LEDs will light up. All keys‟ name will display in red on LCD screen before diagnosing. Press any key on the keypad to diagnose the key‟s function.When done, the key‟s name will display in blue on LCD.
The following picture shows the keypad MENU configuration flow: GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 ADMINISTRATION GUIDE Page 28 of 85
MENU Call History Local CallLog Status Account Status Network Status System information Contacts Messages Preference Phone System Local Phonebook Local Group LDAP Directory Instant Messages Voice Mails Do Not Disturb Star Key Lock Sounds Appearance Language and Input Date Time Search Mode SIP Call Features Network Bluetooth(GXP2140/60 only) Upgrade Language Download Factory Functions UCM Detect Factory Reset Reboot Enable/Disable Password Ring Tone Ring Volume Active LCD Brightness Idle LCD
CONFIGURATION VIA WEB BROWSER The GXP2130/GXP2140/GXP2160/GXP2170/GXP2135embedded Web server responds to HTTP/HTTPS GET/POST requests. Embedded HTML pages allow a user to configure the IP phone through a Web browser such as Google Chrome, Mozilla Firefox andMicrosoft‟s IE. To access the Web GUI: 1. Connect the computer to the same network as the phone; 2. Make sure the phone is turned on andshows its IP address. You may check the IP address by pressing Up arrow button when phone is at idle state; 3.
DEFINITIONS This section describesthe options in the phone'sWeb GUI. As mentioned,youcanlog in as an administrator or an end user. Status: Displays the Account status,Network status, and System Info of the phone; Account: To configure the SIP account; Settings: To configure call features, ring tone, audio control, LCD display, date and time, Web services, XML applications, programmable keysand etc.
PPPoE Link Up PPPoE connection status. NAT Type The type of NAT connection used by the phone. NAT Traversal Display the status of NAT connection for each account on the phone. Status System Info Product Model Product model of the phone. Part Number Product part number. Software Version IP Geographic Information Boot: boot version number; Core: core version number; Base: base version number; Prog: program version number.
status on the SIP server. User account information, provided by your VoIP service provider (ITSP). It's SIP User ID usually in the form of digits similar to phone number or actually a phone number. SIP service subscriber's Authenticate ID used for authentication. It can be Authenticate ID identical to or different from the SIP User ID. The account password required for the phone to authenticate with the ITSP Authenticate Password (SIP) server before the account can be registered.
to the STUN server. If NAT type is Full Cone, Restricted Cone or Port-Restricted Cone, the phone will try to use public IP addresses and port number in all the SIP&SDP messages. The phone will send empty SDP packet to the SIP server periodically to keep the NAT port open if it is configured to be "Keep-alive". Configure this to be "No" if an outbound proxy is used. "STUN" cannot be used if the detected NAT is symmetric NAT. Set this to "VPN" if OpenVPN is used.
Determines the network protocol used for the SIP transport. Users can choose SIP Transport from TCP, UDP and TLS. The default setting is “UDP”. SIP URI Scheme when Specifies if "sip" or "sips" will be used when TLS/TCP is selected for SIP using TLS Transport. The default setting is "sips". Use Actual Ephemeral Port in Contact with This option is used to control the port information in the Via header and Contact header.
"Yes", the P-Preferred-Identity Header will always show in INVITE. If set to "No", the P-Preferred-Identity Header will not show in INVITE. Add Auth Header on To define whether authorization Header will be added on initial REGISTER Initial REGISTER from the first REGISTER. The default setting is “No”. This is used to perform afactory reset through SIP NOTIFY. When the phone Allow SIP Reset receive the NOTIFY with event: RESET, the phone should perform a factory reset after the authentication.
"Standard". Default setting is "No". When set to "Yes", a soft key “BSCCenter” is displayed on LCD. User can access different Broadsoft Call Center agent features via Broadsoft Call Center this softkey. Please note that “Feature Key Synchronization” will be enabled regardless of this setting. Broadsoft Hoteling event feature. Default setting is "No". With “HotelingEvent” Hoteling Event enabled, user can access the Hoteling feature option by pressing the “BSCCenter” sof tkey.
use the Callee or proxy server as the refresher. The default setting is "Omit". UAS Specify Refresher As a Callee, select UAC to use caller or proxy server as the refresher; or select UAS to use the phone as the refresher. The default setting is "UAC". The Session Timer can be refreshed using the INVITE method or the UPDATE Force INVITE method. Select "Yes" to use the INVITE method to refresh the session timer. The default setting is "No".
Multiple vocoder types are supported on the phone, the vocoders in the list is a Preferred Vocoder higher preference. Users can configure vocoders in a preference list that is included with the same preference order in SDP message. Use First Matching When it is set to "Yes", the device will use the first matching vocoder in the Vocoder in 200OK SDP received 200OK SDP as the codec. The default setting is "No".
Dial Plan Prefix Configures the prefix to be added to each dialed number. A dial plan establishes the expected number and pattern of digits for a telephone number. This parameter configures the allowed dial plan for the phone. Dial Plan Rules: 1. Accepted Digits: 1,2,3,4,5,6,7,8,9,0 , *, #, A,a,B,b,C,c,D,d; 2.
Note: In some cases where the user wishes to dial strings such as *123 to activate voice mail or other applications provided by their service provider, the * should be predefined inside the dial plan feature. An example dial plan will be: { *x+ } which allows the user to dial * followed by any length of numbers. Configures Call Log setting on the phone. You can log all calls, only log Call Log incoming/outgoing calls (missed calls will not be logged), or disable call log.
If set to "Yes", the phone will automatically turn on the speaker phone to Allow Auto Answer by answer incoming calls, based on the SIP info header sent from the Call-Info server/proxy. The default setting is "No". When it is enabled, the phone will put the current call on hold automatically and answer the incoming calls based on the SIP Call-Info header sent from the Allow Barging by server/proxy.
Call Forward Configures Call Forward All feature code to activate unconditional call Unconditionally (All)--On forwarding. Call Forward Configures Call Forward All feature code to deactivate unconditional call Unconditionally (All)--Off forwarding Call Forward Busy--On Configures Call Forward Busy feature code to activate busy call forwarding. Call Forward Busy--Off Configures Call Forward Busy feature code to deactivate busy call forwarding.
Settings Call Features Configures a User ID/extension to dial automatically when the phone is Off-hook Auto Dial offhook. The phone will use the first account to dial out. The default setting is "No". If configured, when the phone is onhook, it will go offhook after the Off-hook Timeout timeout (in seconds). The default value is 30 seconds. The valid range is from 10 to 60.
Auto-Attended Transfer If set to "Yes", the phone will use attended transfer by default. The default setting is "No". Do Not Escape # as %23 in Specifies whether to replace # by %23or not for some special situations. SIP URI The default setting is "No". Enables Click-To-Dial feature.If this feature is enabled, user could click the green dial button on left top corner of phone‟s Web GUI, then choose Click-To-Dial Feature the account and dial to the target number.The default setting is "Disabled".
Settings Ring Tone Configures ring or tone frequencies based on parameters from local Call Progresses Tones: telecom. The default value is North American standard.Frequencies System Ring Tone should be configured with known values to avoid uncomfortable high Dial Tone pitch sounds.
Configures to enable or disable the speaker to ring when headset is used on "Toggle Headset/Speaker" mode. If set to "Yes", when the phone is in Always Ring Speaker Headset "Toggle Headset/Speaker" mode, both headset and speaker will ring on incoming call. The default setting is "No". Configures the transmission gain of the headset. The default value is Headset TX gain 0dB. Headset RX gain Configures the receiving gain of the headset. The default value is 0dB.
the date and time from the server. The default setting is us.pool.ntp.org. Time interval for updating time from the NTP server. Valid time value is in NTP Update Interval between 5 to 1440 minutes. The default setting is “1440” minutes. Allow DHCP Option 42 Override NTP Server Defines whether DHCP Option 42 should override NTP server or not. When enabled, DHCP Option 42 will override the NTP server if it's set up on the LAN. The default setting is "Yes".
Configures weather city code for the phone to look up the weather information. The default setting is "Automatic" and the weather City Code information will be obtained based on the IP location of the phone if available. Otherwise, specify the self-defined city code. For example, USCA0638 is the city code for Los Angeles, CA, United States. Specifies the weather update interval (in minutes). The default value is Update Interval 15 minutes.
Presence Watcher This option has to be supported by a presence server and it is tied to the "Do Not Disturb" status of the phone's extension. Eventlist BLF This option is similar to the BLF option but in this case the PBX collects the information from the phones and sends it out in one single notify message.PBX server has to support this feature. Speed Dial via active account Similar to Speed Dial but it will dial based on the current active account.
blank. Enter the LDAP Name/Number filter in the Value field. For example: If users set MPK 1 as “LDAP Search” for “Account 1”, and set filters: Description -> ou=video,ou=SZ,dc=grandstream,dc=com Value -> sn=Li Since the Base for LDAP server configuration is “dc=grandstream,dc=com”, “ou=video,ou=SZ” is added to narrow the LDAP search scope. “sn=Li” is the example to filter the last name. Multicast Paging This option is for multicast sending.
Intercom Select Account, and enter the extension number in the Value field to do the intercom. LDAP Search This option is to narrow the LDAP search scope. Enter the LDAP search base in the Description field. It could be the same or different from the Base in LDAP configuration under Advanced Settings. The Base in LDAP configuration will be used if the Description field is left blank. Enter the LDAP Name/Number filter in the Value field.
it will call the configured Speed Dial number using account 2. Dial DTMF Enter a series of DTMF digits in the Value field to be dialed during the call. "Enable MPK Sending DTMF" has to be set to "Yes" first. Voice Mail Select Account and enter the Voice Mail access number in the Value field. Call Return The last answered calls can be dialed out by using Call Return. The Value field should be left blank.
Description filed and multicast sending address in Value field. Record This option is for Recording calls. Enter Line key description in Description filed and the recorded extension number in Value field. Please make sure whether your VOIP provider supports this feature before using it. Call Log Select Account and enter account number in the Value field to access to the Call Log of that selected account.
If users set MPK 1 as “LDAP Search” for “Account 1”, and set filters: Description -> ou=video,ou=SZ,dc=grandstream,dc=com Value -> sn=Li Since the Base for LDAP server configuration is “dc=grandstream,dc=com”, “ou=video,ou=SZ” is added to narrow the LDAP search scope. “sn=Li” is the example to filter the last name. Call Log Select Account and enter account number in the Value field to access to the Call Log of that selected account.
the call. "Enable MPK Sending DTMF"has to be set to "Yes" first. Voice Mail Select Account and enter the Voice Mail access number in the Value field. Call Return The last answered calls can be dialed out by using Call Return. The Value field should be left blank. Also, this option is not binding to the account and the call will be returned based on the account with the last answered call.
Description filed and the recorded extension number in Value field. Please make sure whether your VOIP provider supports this feature before using it. Call Log Select Account and enter account number in the Value field to allow configuration of call log for other extension. Menu This option is to take users to the main menu screen directly. Settings Broadsoft Broadsoft Directories Configures XSI Directory. Server Configure the BroadWorks Xsi server URI.
Common Directory features on the phone. If keep the Name box blank, the phone will use the default name “Enterprise Common” for it. Personal Directory Enable/Disable and rename the BroadWorks Xsi Personal Directory features on the phone. If keep the Name box blank, the phone will use the default name “Personal” for it. Missed Call Log Enable/Disable and rename the BroadWorks Xsi Missed Call Log features on the phone. If keep the Name box blank, the phone will use the default name “Missed” for it.
NETWORK PAGE DEFINITIONS Table 12: Network Page Definitions Network Basic Settings Selects Prefer IPv4 or Prefer IPv6. The default setting is “Prefer IPv4”. Internet Protocol Allows users to configure the appropriate network settings on the phone to IPv4 Address Type obtain IPv4 address. Users could select "DHCP", "Static IP" or "PPPoE". By default, it is set to "DHCP". DHCP Host name Specifies the name of the client.
EAP-MD5, users may also choose EAP-TLS, or EAP-PEAP. 802.1X Identity Enter the Identity information for the 802.1x mode. MD5 Password Enter the MD5 Password for the 802.1X mode. Upload 802.1X CA certificate to the phone; or delete existed 802.1X CA 802.1X CA Certificate certificate from the phone. 802.1X Client Certificate Upload 802.1X Client certificate to the phone; or delete existed 802.1X Client certificate from the phone. Specifies the HTTP proxy URL for the phone to send packets to.
Confirm Password Enter the new Admin password again to confirm. Maintenance Upgrade and Provisioning Specifies how firmware upgrading and provisioning request to be sent: Firmware Upgrade and Always Check for New Firmware, Check New Firmware only when F/W Provisioning pre/suffix changes, Always Skip the Firmware Check. The default setting is “Always Check for New Firmware”. The password for encrypting the XML configuration file using OpenSSL.
Allow DHCP Option 120 Enables DHCP Option 120 from local server to override the SIP Server on to override SIP Server the phone. The default setting is "No". Enables automatic provision feature on the phone when 3CX is used as the 3CX Auto Provision SIP server. The default setting is "Yes". Automatic Upgrade Enables automatic upgrade and provisioning. The default setting is "No".
Maintenance Language Selects display language on the phone. There are 21 languages can be set as display language, user could also choose “Auto” or “Downloaded Display Language Language” as display language. The default setting is “Auto”. Configure the default input selection. Default Input Selection Multi-Tap: multi-tap to switch character; Shiftable: select input from available characters. The default setting is “Multi-Tap”.
If set to "Yes", the keypad can be locked by pressing and holding the STAR * key for about 4 seconds. A lock icon will show indicating the keypad is Enable STAR key locked. The default setting is "Yes". Keypad Locking Note: When the keypad is locked, users would need press and hold the STAR * key for about 4 seconds again and then enter the password to unlock it. Password to Configures the password to lock/unlock the keypad.
Delete All Contacts Deletes all contacts from phonebook. PhonebookGroup Management Add Group Specifies Group‟s name to add new group. Edit Group Edits selected group. Phonebook Phonebook Management Enable Phonebook XML Download Configures to enable phonebook XML download. Users could select HTTP/HTTPS/TFTP to download the phonebook file. The default setting is "Disabled". HTTP/HTTPS User The user name for the HTTP/HTTPS server. Name HTTP/HTTPS Password The password for the HTTP/HTTPS server.
Example: dc=grandstream,dc=com ou=Boston, dc=grandstream,dc=com Configures the bind "Username" for querying LDAP servers. Some LDAP User Name servers allow anonymous binds in which case the setting can be left blank. Configures the bind "Password" for querying LDAP servers. The field can be Password left blank if the LDAP server allows anonymous binds. Configures the filter used for number lookups.
%cn %sn %telephoneNumber Specifies the maximum number of results to be returned by the LDAP server. If Max. Hits set to 0, server will return all search results. The default setting is 50. Specifies the interval (in seconds)for the server to process the request and Search Timeout client waits for server to return. The default setting is 30 seconds. Specifies whether the searching result is sorted or not. The default setting is Sort Results "No".
Pattern: Directional Mode: Inverse Call’s state Light Indication Call’s state Light Indication Offline Off Offline Off Idle Solid Green Idle Solid Red Trying Flashing Green Trying Solid Green Talking Solid Red Talking Solid Green Flashing Green Proceeding Flashing Green Flashing Red Incoming call Flashing Green Proceeding (Initiator) Proceeding (Receiver) Incoming call Flashing Red Mode: Reverved (Red) Call’s state Offline Idle Light Indication Off (Extension Board Icon: Off
NAT SETTINGS If the devices are kept within a private network behind a firewall, we recommend using STUN Server. Thefollowing settings are useful in the STUN Server scenario: STUN Server Under Settings->General Settings, enter a STUN Server IP (or FQDN) that you may have, or look up a free public STUN Server on theinternet and enter it on this field. If using Public IP, keep this field blank. Use Random Ports It is under Settings->General Settings.This setting depends on your network settings.
WEATHER UPDATE To customize GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 to display weather information for the preferred city, users could go to web GUI->Settings->Web Service page and enter the city code in the following options: Figure 2: Web Service By default the City Code is set to "Automatic", which allows the phone to obtain weather information based on the IP location detected.
EDITING CONTACTS AND CLICK-TO-DIAL From GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 Web GUI, users could view contacts, edit contacts, or dial out with Click-to-Dial feature onthe top of the Web GUI. In the following figure, the Contact page shows all the added contacts (manually or downloaded via XML phonebook). Here users could add new contact, edit selected contact, or dial the contact/number.
Click to dial from available lines. Add contacts. Click to call this Edit contact. contact from the phone.
WALLPAPER GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 support 3 approaches for wallpaper configurations: “Default”, “Download”, and “Upload”.GXP2140/GXP2160/GXP2170 also provide loading wallpaper file from USB drive. Default Mode Under Default mode, the phone will display the wallpaper supplied by firmware. Download Mode Under Download mode, the phone will download the wallpaper from the specifiedserver path under “Wallpaper Server Path”option.
Figure 6: Upload Selected Wallpaper to Phone SAVING THE CONFIGURATION CHANGES After users makes changes to the configuration, press the "Save" button will save but not apply the changes until the "Apply" button on the top of web GUI page is clicked. Or, users could directly press "Save and Apply" button.We recommend rebooting or powering cycle the phone after applying all the changes.
To connect to a Bluetooth device, turn on GXP2130v2/2140/GXP2160/GXP2170‟s Bluetooth radio first.The first time when using a new Bluetooth device with the GXP2130v2/2140/GXP2160/GXP2170, "pair" the device with the phone so that both devices know how to connect securely to each other.After that, users could simply connect to a paired device.Turn off Bluetooth if it's not used. Bluetooth related settings are under GXP2130v2/2140/GXP2160/GXP2170's LCD Menu->System->Bluetooth.
User can also define whether RTP packets will be captured or not from With RTP Packets option. Note: Only GXP2140/GXP2160/GXP2170 supports USB connection. Figure 8: Capture toUSB Drive Figure 9: Capture to Internal Storage When the capture configuration is set, press Start button to start packet capture. The Status will become RUNNING while capturing, as showed in Figure 8 and Figure 9.PressStop button to end capture.
MULTICAST PAGGING GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 supports multicast paging, including sending and listening. On the phone, users could send multicast page by setting the multicast address and port. Also, users can listen to at most 10 different multicast IP address. Multicast sender related settings are under Web UI, Settings ->Programmable keys. Select Multicast paging as the key mode for dial page call.Multicast paging listening related settings are under Web UISettings -> Multicast Paging.
This page intentionally left blank GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 ADMINISTRATION GUIDE Page 78 of 85
UPGRADING AND PROVISIONING The GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 can be upgraded via TFTP/HTTP/HTTPS by configuring the URL/IP Address for the TFTP/HTTP/HTTPS server and selecting a download method.Configure a valid URL for TFTP or HTTP/HTTPS; the server name can be FQDN or IP address. Examples of valid URLs: firmware.grandstream.com fw.ipvideotalk.com/gs There are two ways to setup a software upgrade server: The LCDKeypad Menu or the Web Configuration Interface.
UPGRAGE VIA WEB GUI Open a web browser on PC and enter the IP address of the phone. Then, login with the administrator username and password.Go to Maintenance->Upgrade and Provisioning page, enter the IP address orthe FQDN for the upgrade server in "Firmware Server Path" field and choose to upgrade via TFTP or HTTP/HTTPS. Update the change by clicking the "Save and Apply" button. Then "Reboot" or power cycle the phone to update the new firmware.
CONFIGURATION FILE DOWNLOAD Grandstream SIP Devices can be configured via the Web Interface as well as via a Configuration File (binary or XML) through TFTP or HTTP/HTTPS. The "Config Server Path" is the TFTP or HTTP/HTTPS server path for the configuration file. It needs to be set to a valid URL, either in FQDN or IP address format. The "Config Server Path" can be the same or different from the "Firmware Server Path".
This page intentionally left blank GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 ADMINISTRATION GUIDE Page 82 of 85
RESTORE FACTORY DEFAULT SETTINGS Warning: Restoring the Factory Default Settings will delete all configuration information on the phone.Please backup or print all the settings before you restore to the factory default settings. Grandstream is not responsible for restoring lost parameters and cannot connect your device to your VoIP service provider.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
EXPERIENCING THE GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 Please visit our website: http://www.grandstream.com to receive the most up- to-date updates on firmware releases, additional features, FAQs, documentation and news on new products. We encourage you to browse our product related documentation, FAQs and User and Developer Forum for answers to your general questions.
