Grandstream Networks, Inc.
This page is intentionally left bank
HT802 USER MANUAL INDEX GNU GPL INFORMATION ........................................................................... 4 WELCOME .................................................................................................... 5 SAFETY COMPLIANCES ................................................................................................................. 5 WARRANTY .....................................................................................................................................
Preferred VOCODER (Codec) ................................................................................................. 23 SAVING THE CONFIGURATION CHANGES ................................................................................. 38 REBOOTING THE HT802 FROM REMOTE.................................................................................... 38 SOFTWARE UPGRADE ............................................................................. 39 FIRMWARE UPGRADE THROUGH TFTP/HTTP/HTTPS ........
T ABLE OF FIGURES HT802 USER MANUAL FIGURE 1: DIAGRAM OF HT802 ............................................................................................................... 8 T ABLE OF T ABLES HT802 USER MANUAL TABLE 1: DEFINISIONS OF THE HT802 CONNECTORS ................................................................................... 9 TABLE 2: BASIC DEFINITIONS OF THE HT802 LEDS PATTERN......................................................................... 9 TABLE 4: HT802 SOFTWARE FEATURES ....
GNU GPL INFORMATION HT802 firmware contains third-party software licensed under the GNU General Public License (GPL). Grandstream uses software under the specific terms of the GPL. Please see the GNU General Public License (GPL) for the exact terms and conditions of the license. Grandstream GNU GPL related source code can be downloaded from Grandstream web site from: http://www.grandstream.com/support/faq/gnu_gpl . FIRMWARE VERSION 1.0.0.
WELCOME Thank you for purchasing Grandstream‘s HT802, the affordable, feature rich Analog Telephone Adaptor. Grandstream HandyTone802 is a new addition to the popular HandyTone ATA product family. It features the rich audio quality, a broad range of voice codecs, and functionality including one independent SIP account per FXS port.
This page is intentionally left bank FIRMWARE VERSION 1.0.0.
CONNECT YOUR HT802 Connecting the HT802 is easy. Before you begin, please verify the contents of the HT802 package. EQUIPMENT PACKAGING The HT802 ATA package contains: One HT802 Main Case One Universal Power Adaptor One Ethernet Cable One Vertical Stand (Only on HT702 and HT704 Packages) CONNECTING THE HT802 The HT802 is designed for easy configuration and easy installation. Configure the HT802 following the directions in the Configuration section of this manual. 1.
FIGURE 1: DIAGRAM OF HT802 FIRMWARE VERSION 1.0.0.
TABLE 1: DEFINISIONS OF THE HT802 CONNECTORS Power Micro USB 5V 1A Internet Port (RJ-45) Connect to network. RESET Factory Reset button: Press for 7 seconds to reset factory default settings. Telephone Ports (RJ-11) Used to connect to analog phones / fax machines. There are four (4) LED buttons that help you manage the status of your HandyTone 802. TABLE 2: BASIC DEFINITIONS OF THE HT802 LEDS PATTERN POWER LED Indicates Power.
This page is intentionally left bank FIRMWARE VERSION 1.0.0.
HT802 FEATRUES The HT802 is a full feature voice and fax-over IP device that offers a high-level of integration including a 10M/100Mbps network port and one FXS telephone port, market-leading sound quality, rich functionalities, and a compact and lightweight design. The VoIP network signaling protocol supported is SIP. The HT802 is fully compatible with SIP industry standard and can interoperate with many other SIP compliant devices and software on the market.
DHCP Server/Client Yes, DHCP Client only Telnet Server Yes Fax over Ip T.38 compliant Group 3 Fax Relay up to 14.4kpbs and auto-switch to G.711 for Fax Passthrough, Fax Datapump V.17, V.19, V.27ter, V.29 for T.38 fax relay QoS Diffserve, TOS, 802.
BASIC OPERATIONS UNDERSTANDING HT802 VOICE PROMPT HT802 has a built-in voice prompt menu for simple device configuration. The IVR menu and the LED button work with any of the FXS port. Pick up the handset and dial ―***‖ to use the IVR menu.
Firmware Version Firmware version information. 17 Firmware Upgrade Firmware upgrade mode. Press ―9‖ to toggle among the following three options: - always check - check when pre/suffix changes - never upgrade 47 ―Direct IP Calling‖ Enter the target IP address to make a direct IP call, after dial tone. (See ―Make a Direct IP Call‖.
Examples: 1. Dial an extension directly on the same proxy, (e.g. 1008), and then press the # or wait for 4 seconds. 2. Dial an outside number (e.g. (626) 666-7890), first enter the prefix number (usually 1+ or international code) followed by the phone number. Press # or wait for 4 seconds. Check with your VoIP service provider for further details on prefix numbers.
b) If the target IP address/port is 192.168.1.20:5062, then the dialing convention would be: *47 or Voice Prompt with option 47, then 192*168*0*160*5062 followed by pressing the ―#‖ key if it is configured as a send key or wait for 4 seconds. NOTE: When completing direct IP call, the ―Use Random SIP/RTP Port‖ should set to ―NO‖. You cannot make direct IP calls between FXS1 to FXS2 since they are using same IP.
NOTE: When Attended Transfer fails and A hangs up, the HT802 will ring back user A to remind A that B is still on the call. A can pick up the phone to resume conversation with B. 3-WAY CONFERENCING The HT802 supports Bellcore style 3-way Conference. Instructions for 3-way conference: Assume that call party A and B are in conversation. Caller A(HT802) wants to bring third Caller C into conference: 1. A presses FLASH (on the analog phone, or Hook Flash for old model phones) to get a dial tone. 2.
This page is intentionally left bank FIRMWARE VERSION 1.0.0.
CALL FEATURES The HT802 supports all the traditional and advanced telephony features. TABLE 6: HT802 CALL FEATURES CALL FEATURES KEY *02 Forcing a Codec (per call) *027110 (PCMU), *027111 (PCMA), *02723 (G723), *02729 (G729), *0272616 (G726-r16), *0272624 (G724-r24), *0272632 (G726-r32), *0272640 (G726-r40), *027201 (iLBC) *03 Disable LEC (per call) Dial ―*03‖ + ‖ number ‖. No dial tone is played in the middle.
then hang up. Flash/Hook Toggles between active call and incoming call (call waiting tone). If not in conversation, flash/hook will switch to a new channel for a new call. # Pressing pound sign will serve as Re-Dial key. FIRMWARE VERSION 1.0.0.
CONFIGURATION GUIDE CONFIGURING THE HT802 THROUGH VOICE PROMPTS DHCP MODE Select voice menu option 01 to enable HT802 to use DHCP. STATIC IP MODE Select voice menu option 01 to enable HT802 to use STATIC IP mode, then use option 02, 03, 04, 05 to set up IP address, Subnet Mask, Gateway and DNS server respectively. FIRMWARE SERVER IP ADDRESS Select voice menu option 13 to configure the IP address of the firmware server.
2. Open a web browser, type the IP address. You will see the log in page of the device. Note: • The IVR announces 12 digits IP address, you need to strip out the leading ―0‖ in the IP address. For ex. IP address: 192.168.001.014, you need to type in http://192.168.1.14 in the web browser. Once the HTTP request is entered and sent from a web browser, the user will see a log-in screen.
Set this to Yes when gateway is behind firewall on a private network. DTMF METHODS DTMF Settings are in FXS portX/ProfileX page. DTMF in-audio DTMF via RTP (RFC2833) DTMF via SIP INFO Set priority of DTMF methods according to your preference. This setting should be based on your server DTMF setting. PREFERRED VOCODER (CODEC) The HT802 supports a broad range of voice codecs. Under Profile web pages, choose your preferred order of different codecs: PCMU/A (or G711µ/a) G729 A/B G723.
DHCP vendor class ID Default is HT7XX. Used by clients and servers to exchange vendor-specific information.. Time Zone Controls how the date/time is displayed according to the specified time zone. Self-Defined Time Zone The syntax is std offset dst [offset],start[/time],end[/time] Default is set to : MTZ+6MDT+5,M3.2.0,M11.1.0 MTZ+6MDT+5, Time zone with 6 hours offset with 1 hour ahead which is the US central time.
IP Address This field shows the IP address of the HT802. Product Model This field contains the product model info. Hardware Version This field shows the hardware revision of the unit and the part number. Software Version Program: This is the main software release. This number is always used for firmware upgrade. Current release is 1.0.3.1. Boot and Loader are seldom changed. Bootloader: current version is 1.0.0.7. Core: current version 1.0.3.1. Base: current version is 1.0.3.1.
Advanced User configuration includes the end user configuration and the advanced configurations including: a) SIP configuration, b) Codec selection, c) NAT Traversal Setting and d) other miscellaneous configuration. TABLE 9: ADVANCED SETTINGS Admin Password This contains the password to access the Advanced Web Configuration page. This field is case sensitive. Only the administrator can configure the ―Advanced Settings‖ page.
to 15 or 20 minutes. Via HTTP / HTTPS The URL for the HTTP/HTTPS server used for firmware upgrade and configuration via Server HTTP. For example, http://provisioning.mycompany.com:6688/Grandstream/1.0.0.67―:6688‖ is the specific TCP port where the HTTP or HTTPS server is listening; it can be omitted if using default port 80. Note: If Auto Upgrade is set to No, HT802 will only do HTTP/HTTPS download once at boot up. Firmware Server Path IP address or domain name of firmware server.
Authenticate Conf File If set to Yes, config file is authenticated before acceptance. This protects the configuration from an unauthorized change. SIP TLS Certificate The user specify SSL certificate used for SIP over TLS in X.509 format. SIP TLS Private Key The user specify SSL private key used for SIP over TLS in X.509 format. SIP TLS Private Key User specify password to protect the private key above.
(Note: freq: 0 - 4000Hz; vol: -30 - 0dBm) Feature Activation Blind Transfer Code: Custom the Blind Transfer Code (Default #90). Codes (* or # followed by 1-5 digits) Lock Keypad Update Default is No. If set to ―Yes‖, the configuration update via keypad is disabled. Disable Voice Prompt Default is No. Disables the voice prompt configuration. Disable Direct IP Call Default is No. Disables the Direct IP Call function. NTP server URI or IP address of the NTP (Network Time Protocol) server.
is up Default is No. If Enabled, the HT802 will send a replicate of the SIP packets on the Send SIP Log syslog. Download Device Allows user to download and save a text file containing all the P values of each setting as Configuration configured at that point on the unit. (Note: For Security Reasons, all Passwords won‘t be Downloaded) Upload Firmware Allows the user to upgrade the firmware with a single firmware file by browsing and loading the file from your computer (local directory).
Authenticate Password SIP service subscriber‘s account password. Name SIP service subscriber‘s name for Caller ID display. DNS Mode One from the 3 modes are available for ―DNS Mode‖ configuration: -A Record (for resolving IP Address of target according to domain name) -SRV (DNS SRV resource records indicates how to find services for various protocols) -NAPTR/SRV (Naming Authority Pointer according to RFC 2915) One mode can be chosen for the client to look up server.
NAT. Enable RTCP Default is Yes. Enable/Disable RTCP to provides out-of-band statistics and control information for RTP session. Refer-to Use Target Default is No. If set to YES, then for Attended Transfer, the ―Refer-To‖ header uses the Contact transferred target‘s Contact header information. Transfer on Conference Default is No. In which case if the conference originator hangs up the conference will Hang up be terminated.
Offhook Auto-Dial This parameter allows users to configure a User ID or extension number that is automatically dialed when off-hook. Only the user part of a SIP address needs to be entered here. The HT802 will automatically append the ―@‖ and the host portion of the corresponding SIP address. Offhook Auto-Dial The auto-dial delay after off hook. Delay Proxy-Require SIP Extension to notify SIP server that the unit is behind the NAT/Firewall. Use NAT IP NAT IP address used in SIP/SDP message.
phone connected to the FXS port. Ring Timeout Default value is 60 Sec. Incoming call will stop ringing when not picked up given a specific period of time. Delayed Call Forward Default value is 20 seconds. In case this feature activated using * codes (*92 code), Wait Time the call will be forwarded after this preconfigured amount of time. No Key Entry Timeout Default is 4 seconds. Dialing process is completed and outgoing call is initiated if no key entry occurs during this preconfigured interval.
1900 and add prefix 1617 for any dialed 7 digit numbers • Example 3: {1xxx[2-9]xxxxxx | <2=011>x+} –Allow any combinations of numbers with 11 digits which has a leading digit 1, but 5th digit cannot be 0 or 1. Or any length of numbers with a minimum of 2 digits beginning with 2, with the leading digit replaced with 011. 3. Default: Outgoing - {x+} Example of a simple dial plan used in a Home/Office in the US: { ^1900x. | <=1617>[2-9]xxxxxx | 1[2-9]xx[2-9]xxxxxx | 011[2-9]x.
Callee Request Timer Default is No. If selecting ―Yes‖ the phone will use session timer when it receives inbound calls with session timer request. Force Timer Default is No. If selecting ―Yes‖ the phone will use session timer even if the remote party does not support this feature. Selecting ―No‖ will allow the phone to enable session timer only when the remote party support this feature. To turn off Session Timer, select ―No‖ for Caller Request Timer, Callee Request Timer, and Force Timer.
Jitter Buffer Type Select either Fixed or Adaptive based on network conditions. Default is Adaptive. Jitter Buffer Length Select Low, Medium or High based on network conditions. Default is Medium. High (initial 200ms, min 40ms, max 600ms) Note: not all vocoders can meet the high requirement SRTP Mode Medium (initial 100ms, min 20ms, max 200ms) Low (initial 50ms, min 10ms, max 100ms) This option defines different implementation of support SRTP (squired RTP) transmission mode.
Ring Tones This function lets you configure ring tone cadence preferences. User has 10 choices. The configuration, completed in Distinctive Ring Tones block in the same page, applies to ring tones cadences configured here. SAVING THE CONFIGURATION CHANGES Click the ―Update‖ button in the Configuration page to save the changes to the HT802 configuration. The following screen confirms that the changes are saved. Reboot or power cycle the HT802 to make the changes take effect.
SOFTWARE UPGRADE Software upgrade can be done via either TFTP or HTTP. The corresponding configuration settings are in the ADVANCED SETTINGS configuration page. FIRMWARE UPGRADE THROUGH TFTP/HTTP/HTTPS To upgrade via TFTP or HTTP/HTTPS, the ―Firmware Upgrade and Provisioning upgrade via‖ field needs to be set to TFTP HTTP or HTTPS, respectively. ―Firmware Server Path‖ needs to be set to a valid URL of a TFTP or HTTP server, server name can be in either FQDN or IP address format.
Grandstream‘s latest firmware is available at http://www.grandstream.com/support/firmware . Oversea users are strongly recommended to download the binary files and upgrade firmware locally in a controlled LAN environment. Note: Alternatively, the user can upload the firmware single file from his/her computer using a local directory. For more instructions see below. Also the user can download a free TFTP or HTTP server and conduct local firmware upgrade.
file. It needs to be set to a valid URL, either in FQDN or IP address format. The ―Config Server Path‖ can be same or different from the ―Firmware Server Path‖. A configuration parameter is associated with each particular field in the web configuration page. A parameter consists of a Capital letter P and 1 to 3 (Could be extended to 4 in the future) digit numeric numbers. i.e., P2 is associated with ―Admin Password‖ in the ADVANCED SETTINGS page.
Automatic Upgrade: No Yes, every Yes, daily at hour FIRMWARE VERSION 1.0.0.5 minutes(60-5256000). (0-23). Yes, weekly on day HT802 USER MANUAL (0-6).
RESTORE FACTORY DEFAULT SETTING WARNING! Restoring the Factory Default Setting will DELETE all configuration information of the phone. Please BACKUP or PRINT out all the settings before you approach to following steps. Grandstream will not take any responsibility if you lose all the parameters of setting and cannot connect to your VoIP service provider. FACTORY RESET There are three (3) methods for resetting your unit: RESET BUTTON Reset default factory settings following these four (4) steps: 1.
C: 2222 D: 33 (press the ―3‖ key twice, ―D‖ will show on the LCD) E: 333 F: 3333 For example: if the MAC address is 000b8200e395, it should be keyed in as ―0002228200333395‖. RESET FROM WEB INTERFACE (RESET TYPE) 1.
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
