EZ Metal Roof Mount Attachments EZ Metal Roof Mount Attachments With L-Foot, Standoffs and Variants Pub.
EZ Metal Roof Mount Attachments Please read carefully before installing Patent # US8122648B SunModo’s EZ Metal Roof Mount Attachments can be used to mount PV panels on metal roofs. All installations shall be in accordance with NEC requirements in the USA. Table of Contents Installer Responsibility: .............................................................................................................. 3 Safety: .......................................................................................
EZ Metal Roof Mount Attachments Installer Responsibility: Before ordering and installing materials, all system layout dimensions should be confirmed by field measurements. SunModo reserves the right to alter, without notice, any details, proposals or plans. Any inquiries that you may have concerning installation of the PV system should be directed to your SunModo Sales representative. Consult SunModo Sales for any information not contained in this manual.
EZ Metal Roof Mount Attachments EZ Metal Roof Mount Series: EZ Metal Roof Mount Kit includes: L-Foot Metal Roof Shoe and Gasket 4” Lag Bolt AL Hex Cap 3/8” Flange Nut and Bolt K10082-001 EZ Metal Roof Mount with L-Foot (as shown) K20082-002 EZ Metal Roof Mount with L-Tall Foot Both are available in black (-BK1 or BK2) EZ Metal Roof Mount Standoff Kit: L-Foot Roof Shoe and Gasket 4” Lag Bolt AL Hex Cap 3/8” Flange Nut and Bolt Standoff: 2” shown K10064-XXX EZ Metal Roof Mount with
EZ Metal Roof Mount Attachments Primary Materials: Aluminum L-Foot are offered in clear, black and brown. A20027-001 AL L-Foot Two Screw Aluminum L-Foot are offered in clear and black. A20113-001 AL L-Foot Two Screw Aluminum T-Foot are offered in clear and black. A20027-004 AL T-Foot AL Hex Cap Available in clear and black A20066-001 and – BK1 AL Hex Cap Aluminum Shoe is provided with EPDM Sealing Washer installed. 5/16 Stainless Steel Lag Bolts are available lengths: 3.5”, 4”, 4.25” 4.
EZ Metal Roof Mount Attachments Aluminum L-Foot available in clear and black. K10066-XXX Standard L-Foot Kit K10096-XXX Tall L-Foot Kit Aluminum Standoff heights: 2”, 3”, 5” and 7” (part of EZ Metal Roof Kit K10064XXX) A20049-XXX Standoff (multiple lengths) Aluminum C-Bracket A22001-001 C-Bracket Conduit Clamp for 3/4” and 1” diameter conduit Conduit Mount L-Foot Helio Rails: Features both 1/4” and 3/8” side slots, and 1/4” top slot for clamping PV panels.
EZ Metal Roof Mount Attachments Helio Open Rail: Features wire management channel and both 1/4” and 3/8” side slots, and 1/4” top slot for clamping PV panels. Available in 84”, 124”, 164” and 206” lengths. Last 3 digits denote rail length. 4 stock sizes in clear and black. A20242-XXX (Clear) A20242-XXX-BK (Black) HR150 (Open Channel Rail) 1/4” Slot Open Rail Splice Kit with 4X 1/4-20 Bolts and Flange Nuts with integral grounding. May be repositioned until torqued to final value.
EZ Metal Roof Mount Attachments Tools Required for Installation: Electric Drill or impact driver. Note that the use of an impact driver is strongly discouraged for all stainless nut and bolt hardware. Metal Roofing Bar Drill Bit for lag bolts, pilot hole 7/32” diameter for 5/16” lag bolt 3/8” Socket Wrench Sockets for 3/8” drive sockets, 7/16”, 1/2”, 9/16” and 1-1/16” Torque Wrench 3/8” drive, 0 to 35 ft. lbs. Anti-seize compound (Permatex 80071 or equivalent).
EZ Metal Roof Mount Attachments Caulk gun and silicon sealant ChemLink M1 (or equivalent) for wood and composite roofs. ChemLink DuraLink (or equivalent) for metal roofs. Tape measure Saws for cutting aluminum posts and rails as necessary Other items that can be useful: Chalk or Roofer’s marker to layout Metal Roof. Adaptor for 3/8” socket to drill chuck. Torque Values: These values must be adhered to for mechanical strength.
EZ Metal Roof Mount Attachments Installation Instructions: EZ Metal Roof Mount Kit K20051-XXX 1. From the marked location drill the pilot hole for the Lag Bolt with a 7/32” drill bit. For maximum strength, the hole should not be more than 3” in depth, and a drill stop may be used to insure this. 1 2. To ensure a strong and water tight seal, wipe away excess grease or debris from the mounting location. Fill pilot hole with sealant, such as ChemLink DuraLink for metal roofs.
EZ Metal Roof Mount Attachments Installation Instructions EZ Metal Roof Mounting Standoff Kit K10064-XXX Mount the AL Shoe using steps 1 and 2 (shown above). A. Place AL Standoff on AL Shoe threads and tighten by hand, then by wrench. Use 15 ft.-lbs. nominal torque. A B. Using the 3/8” Flange Bolt (supplied with AL L-Foot) attach to the top of the Standoff. B C. Install AL Rail to L-Foot to the specific orientation. Then, tighten 3/8” Flange Nut to 15 ft-lbs. and Hex Cap to 15 ft-lbs. torque.
EZ Metal Roof Mount Attachments Warranty See www.sunmodo.com for current warranty documents and information.